Skip to content

FAN control OMV Auyfan 0.10.12: gitlab-ci-linux-build-184, Kernel 5.6

Linux
12 3 1.3k 1
  • Hey,

    I will do it in english, hope it is okay. Thanks, for very informative forum.

    My question is, is it possible to control the FAN in the newest OMV Auyfan 0.10.12: gitlab-ci-linux-build-184, Kernel 5.6?
    The install was very easy no problems at all, the only problem is i did try some different commands to reach the fan, but was not able to get it going. Do somebody know how? Thanks.

    Best Regards.
    Soeren

  • Hi Soeren,

    I have this succesfully running.

    Kind Regards
    Martin

  • Hi Soeren,

    I have this succesfully running.

    Kind Regards
    Martin

    @mabs sagte in FAN control OMV Auyfan 0.10.12: gitlab-ci-linux-build-184, Kernel 5.6:

    Hi Soeren,

    I have this succesfully running.

    Kind Regards
    Martin

    Thanks, i will try the fan tool again. I'm almost sure i did try without luck, have you edited something in the fan tool conf..?

  • Hi,

    I only played with two parameters.

    I have two rockpro64 boards, currently one has a small fan and the other one has a large fan.

    Therefore I changed PROFILE_NR accordingly.

    Also I have ALWAYS_ON on true on the one with the large fan, but don't see a difference. The fan goes on and off still, maybe I misinterpreted the parameter.

    Also I just noticed now that the CTL settings of the version on github changed slightly, but I think this only improved the detection depending of the kernel settings.

    M

  • @mabs

    With the new OMV kernel 5.6 image from Auyfan, i can't get the FAN to spin - If the fan spins it runs really slow, no sound from the fan.

    With the FAN tool the master installation "failed" and with the release installation it did report "active"..
    I have installed a 92mm FAN inside the NAS case, it runs on Armbian with kernel 5.4.32

    I will open op the case later today to be sure. Thanks.

  • Hi,

    Now i did find the fan, here it goes "nano /sys/devices/platform/pwm-fan/hwmon/hwmon3/pwm1" it is at "0" can be controlled to "255"

    Best Regards.

  • Yes that is basically the way ATS is doing the changing as well I think, as those /sys entries are in the _CTL variables.

    good that you got it working, or are you only half way?

    M

  • @mabs

    The tool works on all image under 5.4 or so for me. But yes i am at the finish line, just wanted the fan to be always on. Just wanted to share, if someone will run in the same problems. Thanks.

  • Helpful Thread!

    But, ATS don't work for me on kernel 5.6 with ayufan release. Only this command works.

    nano /sys/devices/platform/pwm-fan/hwmon/hwmon3/pwm1
    

    Thanks @soerenderfor for the hint.

  • Ok, problem in ATS is this?

    -- FAN Control[ String ]
    	PWM_CTL		= {
    			"/sys/class/hwmon/hwmon0/pwm1",
    			"/sys/devices/platform/pwm-fan/hwmon/hwmon0/pwm1",
    			"/sys/devices/platform/pwm-fan/hwmon/hwmon1/pwm1"
    	},
    
  • Ok, problem in ATS is this?

    -- FAN Control[ String ]
    	PWM_CTL		= {
    			"/sys/class/hwmon/hwmon0/pwm1",
    			"/sys/devices/platform/pwm-fan/hwmon/hwmon0/pwm1",
    			"/sys/devices/platform/pwm-fan/hwmon/hwmon1/pwm1"
    	},
    

    @FrankM - did you try fix the ATS tool, if yes. Will it Work?

    Best Regards.

  • Hi,

    since I'm currently change my rockpro64 setup I came across this.

    With the kernel from ayufan you need to set PWM_CTL to

    /sys/devices/platform/pwm-fan/hwmon/hwmon3/pwm1
    

    for my self compiled one I need

    /sys/devices/platform/pwm-fan/hwmon/hwmon0/pwm1
    

    But I got it only working with one entry for PWM_CTL e.g.

    PWM_CTL		= "/sys/devices/platform/pwm-fan/hwmon/hwmon0/pwm1",
    

    after that you need to start ats again

    sudo systemctl stop ats
    sudo systemctl start ats
    

    initially the fan should start immediately for a short period of time.

    In case it is even a different one on your kernel you can find the right one using this command.

    sudo find /sys -name pwm1 | grep hwmon
    

    So far I'm not sure which kernel parameter or modul changes this.

    Martin

  • Update 1.32.2 released

    Vaultwarden vaultwarden linux
    1
    0 Stimmen
    1 Beiträge
    162 Aufrufe
    Niemand hat geantwortet
  • KDE neon Unstable Edition

    Linux kde linux plasma
    6
    2
    0 Stimmen
    6 Beiträge
    471 Aufrufe
    FrankMF
    Heute Morgen beim mal die Testinstallation aktualisiert. 484 Pakete [image: 1700901047287-screenshot_20231125_092126.png] Nach dem Klicken auf Alle aktualisieren, startete der Rechner neu und installierte dann die Updates!? Holy Fuck, das erinnert mich an M$. Aber gut, KDE Neon soll ja auch nicht mein Hauptsystem werden.
  • Counter-Strike 2 unter Linux?

    Allgemeine Diskussionen counter-strike steam linux
    2
    5
    0 Stimmen
    2 Beiträge
    351 Aufrufe
    FrankMF
    Ergänzungen Ich hatte Steam auch auf meinem Haupt-PC installiert, da muss es aber wieder runter. Läuft da nicht vernünftig und am PC wird auch nichts geändert. Dafür habe ich ja den anderen eingerichtet. Also, ran ans Aufräumen Installation Steam gibt es auch als Flatpak, aber das habe ich nicht getestet. Wenn es läuft, würde ich das empfehlen. Dann bleibt das System sauber. Deinstallation Das .deb Paket mit der Software Verwaltung öffnen. Auf Deinstallation klicken. Danach waren leider alle Daten noch vorhanden, als Handarbeit rm -R /home/frank/.local/share/Steam
  • Restic v0.16.0 released

    Restic restic linux
    1
    0 Stimmen
    1 Beiträge
    153 Aufrufe
    Niemand hat geantwortet
  • Konsolentext in Englisch

    Linux linux
    1
    0 Stimmen
    1 Beiträge
    80 Aufrufe
    Niemand hat geantwortet
  • Kopia - Kopia-Server mit Kopia-UI

    Kopia kopia linux
    1
    2
    0 Stimmen
    1 Beiträge
    454 Aufrufe
    Niemand hat geantwortet
  • ROCKPro64 - Debian Bullseye Teil 2

    Verschoben ROCKPro64 debian linux rockpro64
    3
    0 Stimmen
    3 Beiträge
    525 Aufrufe
    FrankMF
    Gestern mal das Ganze mit einem Cinnamon Desktop ausprobiert. Eine verschlüsselte Installation auf eine PCIe NVMe SSD. So weit lief das alles reibungslos. Der Cinnamon Desktop hat dann leider keine 3D Unterstützung. Sieht so aus, als wenn keine vernünftigen Grafiktreiber genutzt würden. Da ich auf diesem Gebiet aber eine Null bin, lassen wir das mal so. Außerdem mag ich sowieso keine Desktops auf diesen kleinen SBC. Da fehlt mir einfach der Dampf Gut, was ist mir so aufgefallen? Unbedingt die Daten des Daily Images erneuern, keine alten Images nutzen. Ich hatte da jetzt ein paar Mal Schwierigkeiten mit. Da das ja nun keine Arbeit ist, vorher einfach neu runterladen und Image bauen. Warum zum Henker bootet eigentlich. außer meiner Samsung T5, nichts vom USB3 oder USB-C Port??
  • Let'sEncrypt auf Debian-Server einbauen

    Verschoben Let's Encrypt letsencrypt linux
    1
    0 Stimmen
    1 Beiträge
    836 Aufrufe
    Niemand hat geantwortet