Skip to content

ROCKPro64 (4GB) - Probleme mit der PCIe SATA-Karte??

ROCKPro64
  • Im ersten Teil haben wir die PCie SATA-Karte auf einem ROCKPro64 v2.1 mit 2GB RAM getestet, hier nun der Test mit einem ROCKPro64 v2.0 mit 4GB RAM.

    SATA_4.jpg

    AYUFAN Image

    Hardware

    • ROCKPro64 v2.0 4GB RAM
    • PCIe SATA-Karte
    • 1TB 2,5 Zoll HDD
    • 240GB SSD
    • Boot erfolgt von SD-Karte

    Software

    rock64@rockpro64:~$ uname -a
    Linux rockpro64 4.4.154-1124-rockchip-ayufan-ged3ce4d15ec1 #1 SMP Mon Oct 22 20:59:41 UTC 2018 aarch64 aarch64 aarch64 GNU/Linux
    

    So, gestartet. Mit lspci -vvv mal nach dem rechten sehen.

    rock64@rockpro64:~$ sudo lspci -vvv
    [sudo] password for rock64: 
    00:00.0 PCI bridge: Rockchip Inc. RK3399 PCI Express Root Port Device 0100 (prog-if 00 [Normal decode])
    	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort+ <MAbort+ >SERR+ <PERR+ INTx-
    	Latency: 0
    	Interrupt: pin A routed to IRQ 238
    	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    	I/O behind bridge: 00000000-00000fff
    	Memory behind bridge: fa000000-fa0fffff
    	Prefetchable memory behind bridge: 00000000-000fffff
    	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
    	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
    		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    	Capabilities: [80] Power Management version 3
    		Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
    		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME+
    	Capabilities: [90] MSI: Enable+ Count=1/1 Maskable+ 64bit+
    		Address: 00000000fee30040  Data: 0000
    		Masking: 00000000  Pending: 00000000
    	Capabilities: [b0] MSI-X: Enable- Count=1 Masked-
    		Vector table: BAR=0 offset=00000000
    		PBA: BAR=0 offset=00000008
    	Capabilities: [c0] Express (v2) Root Port (Slot+), MSI 00
    		DevCap:	MaxPayload 256 bytes, PhantFunc 0
    			ExtTag- RBE+
    		DevCtl:	Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
    			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
    			MaxPayload 128 bytes, MaxReadReq 512 bytes
    		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
    		LnkCap:	Port #0, Speed 5GT/s, Width x4, ASPM L1, Exit Latency L0s <256ns, L1 <8us
    			ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+
    		LnkCtl:	ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk-
    			ExtSynch- ClockPM- AutWidDis- BWInt+ AutBWInt+
    		LnkSta:	Speed 5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
    		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
    			Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
    		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
    			Control: AttnInd Off, PwrInd Off, Power+ Interlock-
    		SltSta:	Status: AttnBtn- PowerFlt- MRL+ CmdCplt- PresDet- Interlock-
    			Changed: MRL- PresDet- LinkState-
    		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
    		RootCap: CRSVisible-
    		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
    		DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR+, OBFF Via message ARIFwd+
    		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
    		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
    			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
    			 Compliance De-emphasis: -6dB
    		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
    			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
    	Capabilities: [100 v2] Advanced Error Reporting
    		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
    		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
    		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
    		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
    		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
    		AERCap:	First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
    	Capabilities: [274 v1] Transaction Processing Hints
    		Interrupt vector mode supported
    		Device specific mode supported
    		Steering table in TPH capability structure
    	Kernel driver in use: pcieport
    
    01:00.0 IDE interface: ASMedia Technology Inc. ASM1061 SATA IDE Controller (rev 02) (prog-if 85 [Master SecO PriO])
    	Subsystem: ASMedia Technology Inc. ASM1061 SATA IDE Controller
    	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    	Latency: 0
    	Interrupt: pin A routed to IRQ 239
    	Region 0: I/O ports at <unassigned> [disabled]
    	Region 1: I/O ports at <unassigned> [disabled]
    	Region 2: I/O ports at <unassigned> [disabled]
    	Region 3: I/O ports at <unassigned> [disabled]
    	Region 4: I/O ports at <unassigned> [disabled]
    	Region 5: Memory at fa000000 (32-bit, non-prefetchable) [size=512]
    	Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
    		Address: fee30040  Data: 0000
    	Capabilities: [78] Power Management version 3
    		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    	Capabilities: [80] Express (v2) Legacy Endpoint, MSI 00
    		DevCap:	MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us
    			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
    		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
    			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
    			MaxPayload 128 bytes, MaxReadReq 512 bytes
    		DevSta:	CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
    		LnkCap:	Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <2us
    			ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
    		LnkCtl:	ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk-
    			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
    		LnkSta:	Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
    		DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR-, OBFF Not Supported
    		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
    		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
    			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
    			 Compliance De-emphasis: -6dB
    		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
    			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
    	Capabilities: [100 v1] Virtual Channel
    		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
    		Arb:	Fixed- WRR32- WRR64- WRR128-
    		Ctrl:	ArbSelect=Fixed
    		Status:	InProgress-
    		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
    			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
    			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
    			Status:	NegoPending- InProgress-
    	Kernel driver in use: ahci
    

    Festplatte suchen mit fdisk -l

    Disk /dev/sda: 223.6 GiB, 240057409536 bytes, 468862128 sectors
    Units: sectors of 1 * 512 = 512 bytes
    Sector size (logical/physical): 512 bytes / 512 bytes
    I/O size (minimum/optimal): 512 bytes / 512 bytes
    Disklabel type: dos
    Disk identifier: 0xaa1a7c28
    
    Device     Boot Start       End   Sectors   Size Id Type
    /dev/sda1       32768 468860927 468828160 223.6G 83 Linux
    

    Die Platte mal eben mounten

    rock64@rockpro64:~$ sudo mount /dev/sda1 /mnt
    rock64@rockpro64:~$ ls -la /mnt
    total 88
    drwxr-xr-x 22 root root 4096 Dec 23 09:04 .
    drwxr-xr-x 21 root root 4096 Dec 25 08:05 ..
    drwxr-xr-x  2 root root 4096 Dec  2 00:05 bin
    drwxr-xr-x  3 root root 4096 Dec 23 09:21 boot
    drwxr-xr-x  2 root root 4096 Dec 23 09:19 dev
    drwxr-xr-x 86 root root 4096 Dec 23 09:21 etc
    drwx------  2 root root 4096 Dec 23 09:21 home
    drwx------  2 root root 4096 Dec 23 09:21 lib
    drwx------  2 root root 4096 Dec 23 09:21 lost+found
    drwx------  4 root root 4096 Dec 23 09:21 media
    drwx------  2 root root 4096 Dec 23 09:21 mnt
    drwx------  2 root root 4096 Dec 23 09:21 opt
    dr-x------  2 root root 4096 Dec 23 09:21 proc
    drwx------  2 root root 4096 Dec 23 09:21 root
    drwx------  2 root root 4096 Dec 23 09:21 run
    drwx------  2 root root 4096 Dec 23 09:21 sbin
    drwx------  2 root root 4096 Dec 23 09:21 selinux
    drwx------  2 root root 4096 Dec 23 09:21 srv
    dr-x------  2 root root 4096 Dec 23 09:21 sys
    drwx------  2 root root 4096 Dec 23 09:21 tmp
    drwx------  2 root root 4096 Dec 23 09:21 usr
    drwx------  2 root root 4096 Dec 23 09:21 var
    

    Keine Auffälligkeiten, so weit. Der dmesg sieht auch unauffällig aus.

    Armbian Image

    Hardware

    • ROCKPro64 v2.0 4GB RAM
    • PCIe SATA-Karte
    • 1TB 2,5 Zoll HDD
    • 240GB SSD
    • Boot erfolgt von SD-Karte

    Software

    Welcome to ARMBIAN 5.67.181217 nightly Debian GNU/Linux 9 (stretch) 4.4.167-rockchip64
    

    So, gestartet. Mit lspci -vvv mal nach dem rechten sehen.

    root@rockpro64:~# lspci -vvv
    00:00.0 PCI bridge: Device 1d87:0100 (prog-if 00 [Normal decode])
    	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort+ <MAbort+ >SERR+ <PERR+ INTx-
    	Latency: 0
    	Interrupt: pin A routed to IRQ 224
    	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    	I/O behind bridge: 00000000-00000fff
    	Memory behind bridge: fa000000-fa0fffff
    	Prefetchable memory behind bridge: 00000000-000fffff
    	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
    	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
    		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    	Capabilities: [80] Power Management version 3
    		Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
    		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME+
    	Capabilities: [90] MSI: Enable+ Count=1/1 Maskable+ 64bit+
    		Address: 00000000fee30040  Data: 0000
    		Masking: 00000000  Pending: 00000000
    	Capabilities: [b0] MSI-X: Enable- Count=1 Masked-
    		Vector table: BAR=0 offset=00000000
    		PBA: BAR=0 offset=00000008
    	Capabilities: [c0] Express (v2) Root Port (Slot+), MSI 00
    		DevCap:	MaxPayload 256 bytes, PhantFunc 0
    			ExtTag- RBE+
    		DevCtl:	Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
    			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
    			MaxPayload 128 bytes, MaxReadReq 512 bytes
    		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
    		LnkCap:	Port #0, Speed 5GT/s, Width x4, ASPM L1, Exit Latency L0s <256ns, L1 <8us
    			ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+
    		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk-
    			ExtSynch- ClockPM- AutWidDis- BWInt+ AutBWInt+
    		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
    		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
    			Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
    		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
    			Control: AttnInd Off, PwrInd Off, Power+ Interlock-
    		SltSta:	Status: AttnBtn- PowerFlt- MRL+ CmdCplt- PresDet- Interlock-
    			Changed: MRL- PresDet- LinkState-
    		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
    		RootCap: CRSVisible-
    		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
    		DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR+, OBFF Via message ARIFwd+
    		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
    		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
    			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
    			 Compliance De-emphasis: -6dB
    		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
    			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
    	Capabilities: [100 v2] Advanced Error Reporting
    		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
    		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
    		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
    		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
    		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
    		AERCap:	First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
    	Capabilities: [274 v1] Transaction Processing Hints
    		Interrupt vector mode supported
    		Device specific mode supported
    		Steering table in TPH capability structure
    	Kernel driver in use: pcieport
    
    01:00.0 SATA controller: ASMedia Technology Inc. ASM1062 Serial ATA Controller (rev 02) (prog-if 01 [AHCI 1.0])
    	Subsystem: ASMedia Technology Inc. ASM1062 Serial ATA Controller
    	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    	Latency: 0
    	Interrupt: pin A routed to IRQ 225
    	Region 0: I/O ports at <unassigned> [disabled]
    	Region 1: I/O ports at <unassigned> [disabled]
    	Region 2: I/O ports at <unassigned> [disabled]
    	Region 3: I/O ports at <unassigned> [disabled]
    	Region 4: I/O ports at <unassigned> [disabled]
    	Region 5: Memory at fa010000 (32-bit, non-prefetchable) [size=512]
    	[virtual] Expansion ROM at fa000000 [disabled] [size=64K]
    	Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
    		Address: fee30040  Data: 0000
    	Capabilities: [78] Power Management version 3
    		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    	Capabilities: [80] Express (v2) Legacy Endpoint, MSI 00
    		DevCap:	MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us
    			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
    		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
    			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
    			MaxPayload 128 bytes, MaxReadReq 512 bytes
    		DevSta:	CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
    		LnkCap:	Port #1, Speed 5GT/s, Width x1, ASPM not supported, Exit Latency L0s unlimited, L1 <2us
    			ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
    		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk-
    			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
    		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
    		DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR-, OBFF Not Supported
    		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
    		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
    			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
    			 Compliance De-emphasis: -6dB
    		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
    			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
    	Capabilities: [100 v1] Virtual Channel
    		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
    		Arb:	Fixed- WRR32- WRR64- WRR128-
    		Ctrl:	ArbSelect=Fixed
    		Status:	InProgress-
    		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
    			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
    			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
    			Status:	NegoPending- InProgress-
    	Kernel driver in use: ahci
    

    Festplatte suchen mit fdisk -l

    Disk /dev/sda: 223.6 GiB, 240057409536 bytes, 468862128 sectors
    Units: sectors of 1 * 512 = 512 bytes
    Sector size (logical/physical): 512 bytes / 512 bytes
    I/O size (minimum/optimal): 512 bytes / 512 bytes
    Disklabel type: dos
    Disk identifier: 0xaa1a7c28
    
    Device     Boot Start       End   Sectors   Size Id Type
    /dev/sda1       32768 468860927 468828160 223.6G 83 Linux
    

    Die Platte mal eben mounten

    root@rockpro64:~# mount /dev/sda1 /mnt
    root@rockpro64:~# ls -la /mnt
    total 88
    drwxr-xr-x 22 root root 4096 Dec 23 09:04 .
    drwxr-xr-x 22 root root 4096 Dec 23 09:04 ..
    drwxr-xr-x  2 root root 4096 Dec  2 00:05 bin
    drwxr-xr-x  3 root root 4096 Dec 23 09:21 boot
    drwxr-xr-x  2 root root 4096 Dec 23 09:19 dev
    drwxr-xr-x 86 root root 4096 Dec 23 09:21 etc
    drwx------  2 root root 4096 Dec 23 09:21 home
    drwx------  2 root root 4096 Dec 23 09:21 lib
    drwx------  2 root root 4096 Dec 23 09:21 lost+found
    drwx------  4 root root 4096 Dec 23 09:21 media
    drwx------  2 root root 4096 Dec 23 09:21 mnt
    drwx------  2 root root 4096 Dec 23 09:21 opt
    dr-x------  2 root root 4096 Dec 23 09:21 proc
    drwx------  2 root root 4096 Dec 23 09:21 root
    drwx------  2 root root 4096 Dec 23 09:21 run
    drwx------  2 root root 4096 Dec 23 09:21 sbin
    drwx------  2 root root 4096 Dec 23 09:21 selinux
    drwx------  2 root root 4096 Dec 23 09:21 srv
    dr-x------  2 root root 4096 Dec 23 09:21 sys
    drwx------  2 root root 4096 Dec 23 09:21 tmp
    drwx------  2 root root 4096 Dec 23 09:21 usr
    drwx------  2 root root 4096 Dec 23 09:21 var
    

    Fazit

    Auch hier kann ich berichten, das es mit beiden Images problemlos läuft. Auch hier nochmal die Vermutung, wenn ihr Probleme habt, dann schaut Euch mal die Stromversorgung an, vor allen Dingen wenn ihr 3,5 Zoll Festplatten einsetzt.

    Hat mal wieder Spaß gemacht zu testen, jetzt werde ich mein NAS mal umbauen (siehe ersten Teil).

  • Hmm, bei mir ist die Ausgabe von lspci komplett leer:

    uname -a
    Linux rockpro64 4.20.0-1083-ayufan-g686e1f1aa461 #ayufan SMP PREEMPT Sun Dec 30 13:42:26 UTC 2018 aarch64 GNU/Linux
    rock64@rockpro64:~$ sudo lspci -vvv
    

    Hast du eine Idee woran das liegen kann?

  • @wombat Welche PCIe-Karte probierst du aus?

    Ich habe viele Posts gelesen, das viele User Probleme haben PCIe Karten ans Laufen zu bekommen. Die zwei von Pine64 verkauften Karten, sollten mit Kamils Image laufen.

    Den 4.20er von Kamil habe ich nicht getestet, kann ich aber gerne mal machen.

  • @FrankM Ich versuche eine Telit LM960 LTE Karte mit einem mPCIe auf PCIe Adapter zum Laufen zu bekommen.

    Ich habe weder unter armbian, noch unter Debian Stretch sowohl mit rockchip als auch mainline 4.20 Kernel irgendwas am pcie bus gesehen.
    Der Delock Adapter hat auch eine Status LED - diese leuchtet aber nicht. Da ich die Karte vorher noch nie verwendet habe und aktuell auch nirgendwo anders testen kann, vermute ich einfach mal, dass die LED an sich leuten würde, wenn Strom auf dem Bus hängt, aber das kann ich beim Hersteller nochmal nachfragen.
    Laut Hersteller sind keine Treiber notwendig, da es ein passiver Adapter ist.

    Müsste ich nicht an sich auch ohne PCIe Karte das Rockchip device sehen? Wenn ich das im mainline Kernel richtig sehe, ist pcie0 per default deaktiviert?

  • Die dmesg Ausgabe mit 4.4 kernel ist hier: https://pastebin.com/FHMGRgVG
    Der mit 4.20 Kernel hier: https://pastebin.com/vZw0LhBN

  • Drei Fragen

    • Welchen RockPro64 hast du? Version und Speicher.
    • Du bootest von wo? spi, sdkarte....
    • Welche Erweiterungskarte nutzt du?
  • @FrankM

  • Die Verlinkung hatte ich überlesen, sorry.

    Es gibt nur eine Handvoll Karten, die im PCIe Port funktionieren. Warum, kann ich dir leider nicht beantworten. Es liegt aber mit Sicherheit an falschen Einstellungen im Kernel und an fehlenden Treibern. Ich habe hier auch eine andere Karte rumliegen, die erzeugt immer nur eine Kernel Panic 😞

    In diesem Thread steht einiges was geht und was nicht.
    https://forum.pine64.org/showthread.php?tid=6459

  • Mainline 6.0.x

    Images
    6
    0 Stimmen
    6 Beiträge
    240 Aufrufe
    FrankMF

    Und RC7 released

    Link Preview Image Release 6.7.0-rc7-1185-ayufan · ayufan-rock64/linux-mainline-kernel

    Linux kernel source tree. Contribute to ayufan-rock64/linux-mainline-kernel development by creating an account on GitHub.

    favicon

    GitHub (github.com)

  • ROCKPro WLan Modul

    Verschoben ROCKPro64
    1
    0 Stimmen
    1 Beiträge
    717 Aufrufe
    Niemand hat geantwortet
  • Image 0.7.8 - Latest release

    ROCKPro64
    1
    0 Stimmen
    1 Beiträge
    543 Aufrufe
    Niemand hat geantwortet
  • Bionic Minimal 0.7.8

    ROCKPro64
    2
    0 Stimmen
    2 Beiträge
    563 Aufrufe
    FrankMF

    Testin Testing

  • Mainline Kernel 4.18.0-rc3

    Linux
    1
    0 Stimmen
    1 Beiträge
    961 Aufrufe
    Niemand hat geantwortet
  • stretch-openmediavault-rockpro64

    Verschoben Linux
    1
    0 Stimmen
    1 Beiträge
    805 Aufrufe
    Niemand hat geantwortet
  • stretch-minimal-rockpro64

    Verschoben Linux
    3
    0 Stimmen
    3 Beiträge
    1k Aufrufe
    FrankMF

    Mal ein Test was der Speicher so kann.

    rock64@rockpro64:~/tinymembench$ ./tinymembench tinymembench v0.4.9 (simple benchmark for memory throughput and latency) ========================================================================== == Memory bandwidth tests == == == == Note 1: 1MB = 1000000 bytes == == Note 2: Results for 'copy' tests show how many bytes can be == == copied per second (adding together read and writen == == bytes would have provided twice higher numbers) == == Note 3: 2-pass copy means that we are using a small temporary buffer == == to first fetch data into it, and only then write it to the == == destination (source -> L1 cache, L1 cache -> destination) == == Note 4: If sample standard deviation exceeds 0.1%, it is shown in == == brackets == ========================================================================== C copy backwards : 2812.7 MB/s C copy backwards (32 byte blocks) : 2811.9 MB/s C copy backwards (64 byte blocks) : 2632.8 MB/s C copy : 2667.2 MB/s C copy prefetched (32 bytes step) : 2633.5 MB/s C copy prefetched (64 bytes step) : 2640.8 MB/s C 2-pass copy : 2509.8 MB/s C 2-pass copy prefetched (32 bytes step) : 2431.6 MB/s C 2-pass copy prefetched (64 bytes step) : 2424.1 MB/s C fill : 4887.7 MB/s (0.5%) C fill (shuffle within 16 byte blocks) : 4883.0 MB/s C fill (shuffle within 32 byte blocks) : 4889.3 MB/s C fill (shuffle within 64 byte blocks) : 4889.2 MB/s --- standard memcpy : 2807.3 MB/s standard memset : 4890.4 MB/s (0.3%) --- NEON LDP/STP copy : 2803.7 MB/s NEON LDP/STP copy pldl2strm (32 bytes step) : 2802.1 MB/s NEON LDP/STP copy pldl2strm (64 bytes step) : 2800.7 MB/s NEON LDP/STP copy pldl1keep (32 bytes step) : 2745.5 MB/s NEON LDP/STP copy pldl1keep (64 bytes step) : 2745.8 MB/s NEON LD1/ST1 copy : 2801.9 MB/s NEON STP fill : 4888.9 MB/s (0.3%) NEON STNP fill : 4850.1 MB/s ARM LDP/STP copy : 2803.8 MB/s ARM STP fill : 4893.0 MB/s (0.5%) ARM STNP fill : 4851.7 MB/s ========================================================================== == Framebuffer read tests. == == == == Many ARM devices use a part of the system memory as the framebuffer, == == typically mapped as uncached but with write-combining enabled. == == Writes to such framebuffers are quite fast, but reads are much == == slower and very sensitive to the alignment and the selection of == == CPU instructions which are used for accessing memory. == == == == Many x86 systems allocate the framebuffer in the GPU memory, == == accessible for the CPU via a relatively slow PCI-E bus. Moreover, == == PCI-E is asymmetric and handles reads a lot worse than writes. == == == == If uncached framebuffer reads are reasonably fast (at least 100 MB/s == == or preferably >300 MB/s), then using the shadow framebuffer layer == == is not necessary in Xorg DDX drivers, resulting in a nice overall == == performance improvement. For example, the xf86-video-fbturbo DDX == == uses this trick. == ========================================================================== NEON LDP/STP copy (from framebuffer) : 602.5 MB/s NEON LDP/STP 2-pass copy (from framebuffer) : 551.6 MB/s NEON LD1/ST1 copy (from framebuffer) : 667.1 MB/s NEON LD1/ST1 2-pass copy (from framebuffer) : 605.6 MB/s ARM LDP/STP copy (from framebuffer) : 445.3 MB/s ARM LDP/STP 2-pass copy (from framebuffer) : 428.8 MB/s ========================================================================== == Memory latency test == == == == Average time is measured for random memory accesses in the buffers == == of different sizes. The larger is the buffer, the more significant == == are relative contributions of TLB, L1/L2 cache misses and SDRAM == == accesses. For extremely large buffer sizes we are expecting to see == == page table walk with several requests to SDRAM for almost every == == memory access (though 64MiB is not nearly large enough to experience == == this effect to its fullest). == == == == Note 1: All the numbers are representing extra time, which needs to == == be added to L1 cache latency. The cycle timings for L1 cache == == latency can be usually found in the processor documentation. == == Note 2: Dual random read means that we are simultaneously performing == == two independent memory accesses at a time. In the case if == == the memory subsystem can't handle multiple outstanding == == requests, dual random read has the same timings as two == == single reads performed one after another. == ========================================================================== block size : single random read / dual random read 1024 : 0.0 ns / 0.0 ns 2048 : 0.0 ns / 0.0 ns 4096 : 0.0 ns / 0.0 ns 8192 : 0.0 ns / 0.0 ns 16384 : 0.0 ns / 0.0 ns 32768 : 0.0 ns / 0.0 ns 65536 : 4.5 ns / 7.2 ns 131072 : 6.8 ns / 9.7 ns 262144 : 9.8 ns / 12.8 ns 524288 : 11.4 ns / 14.7 ns 1048576 : 16.0 ns / 22.6 ns 2097152 : 114.0 ns / 175.3 ns 4194304 : 161.7 ns / 219.9 ns 8388608 : 190.7 ns / 241.5 ns 16777216 : 205.3 ns / 250.5 ns 33554432 : 212.9 ns / 255.5 ns 67108864 : 222.3 ns / 271.1 ns
  • ROCKPro64 - PCIe x4

    Verschoben Hardware
    13
    0 Stimmen
    13 Beiträge
    5k Aufrufe
    FrankMF

    @Northstar Hallo, laut meinen Info's nicht, hat irgendwas mit der Speicheradressierung zu tuen. Und Grafikkarten benötigen wohl zu viel. Das ist das, was ich bei den vielen Diskussionen im IRC so aufgeschnappt habe.

    Ich habe es auch schon mal genauso probiert - natürlich ohne Erfolg.