Skip to content
linux-nerds.org

linux-nerds.org
  1. Übersicht
  2. Pine64
  3. ROCKPro64
  4. ROCKPro64 (4GB) - Probleme mit der PCIe SATA-Karte??

ROCKPro64 (4GB) - Probleme mit der PCIe SATA-Karte??

ROCKPro64
  • FrankMF

    Im ersten Teil haben wir die PCie SATA-Karte auf einem ROCKPro64 v2.1 mit 2GB RAM getestet, hier nun der Test mit einem ROCKPro64 v2.0 mit 4GB RAM.

    SATA_4.jpg

    AYUFAN Image

    Hardware

    • ROCKPro64 v2.0 4GB RAM
    • PCIe SATA-Karte
    • 1TB 2,5 Zoll HDD
    • 240GB SSD
    • Boot erfolgt von SD-Karte

    Software

    rock64@rockpro64:~$ uname -a
Linux rockpro64 4.4.154-1124-rockchip-ayufan-ged3ce4d15ec1 #1 SMP Mon Oct 22 20:59:41 UTC 2018 aarch64 aarch64 aarch64 GNU/Linux

    So, gestartet. Mit lspci -vvv mal nach dem rechten sehen.

    rock64@rockpro64:~$ sudo lspci -vvv
[sudo] password for rock64: 
00:00.0 PCI bridge: Rockchip Inc. RK3399 PCI Express Root Port Device 0100 (prog-if 00 [Normal decode])
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort+ <MAbort+ >SERR+ <PERR+ INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 238
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 00000000-00000fff
	Memory behind bridge: fa000000-fa0fffff
	Prefetchable memory behind bridge: 00000000-000fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [80] Power Management version 3
		Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME+
	Capabilities: [90] MSI: Enable+ Count=1/1 Maskable+ 64bit+
		Address: 00000000fee30040  Data: 0000
		Masking: 00000000  Pending: 00000000
	Capabilities: [b0] MSI-X: Enable- Count=1 Masked-
		Vector table: BAR=0 offset=00000000
		PBA: BAR=0 offset=00000008
	Capabilities: [c0] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 256 bytes, PhantFunc 0
			ExtTag- RBE+
		DevCtl:	Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #0, Speed 5GT/s, Width x4, ASPM L1, Exit Latency L0s <256ns, L1 <8us
			ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+
		LnkCtl:	ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt+ AutBWInt+
		LnkSta:	Speed 5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
			Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
			Control: AttnInd Off, PwrInd Off, Power+ Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL+ CmdCplt- PresDet- Interlock-
			Changed: MRL- PresDet- LinkState-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
		DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR+, OBFF Via message ARIFwd+
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [100 v2] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		AERCap:	First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
	Capabilities: [274 v1] Transaction Processing Hints
		Interrupt vector mode supported
		Device specific mode supported
		Steering table in TPH capability structure
	Kernel driver in use: pcieport

01:00.0 IDE interface: ASMedia Technology Inc. ASM1061 SATA IDE Controller (rev 02) (prog-if 85 [Master SecO PriO])
	Subsystem: ASMedia Technology Inc. ASM1061 SATA IDE Controller
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 239
	Region 0: I/O ports at <unassigned> [disabled]
	Region 1: I/O ports at <unassigned> [disabled]
	Region 2: I/O ports at <unassigned> [disabled]
	Region 3: I/O ports at <unassigned> [disabled]
	Region 4: I/O ports at <unassigned> [disabled]
	Region 5: Memory at fa000000 (32-bit, non-prefetchable) [size=512]
	Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee30040  Data: 0000
	Capabilities: [78] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [80] Express (v2) Legacy Endpoint, MSI 00
		DevCap:	MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <2us
			ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
		LnkCtl:	ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR-, OBFF Not Supported
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [100 v1] Virtual Channel
		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
		Arb:	Fixed- WRR32- WRR64- WRR128-
		Ctrl:	ArbSelect=Fixed
		Status:	InProgress-
		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
			Status:	NegoPending- InProgress-
	Kernel driver in use: ahci

    Festplatte suchen mit fdisk -l

    Disk /dev/sda: 223.6 GiB, 240057409536 bytes, 468862128 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0xaa1a7c28

Device     Boot Start       End   Sectors   Size Id Type
/dev/sda1       32768 468860927 468828160 223.6G 83 Linux

    Die Platte mal eben mounten

    rock64@rockpro64:~$ sudo mount /dev/sda1 /mnt
rock64@rockpro64:~$ ls -la /mnt
total 88
drwxr-xr-x 22 root root 4096 Dec 23 09:04 .
drwxr-xr-x 21 root root 4096 Dec 25 08:05 ..
drwxr-xr-x  2 root root 4096 Dec  2 00:05 bin
drwxr-xr-x  3 root root 4096 Dec 23 09:21 boot
drwxr-xr-x  2 root root 4096 Dec 23 09:19 dev
drwxr-xr-x 86 root root 4096 Dec 23 09:21 etc
drwx------  2 root root 4096 Dec 23 09:21 home
drwx------  2 root root 4096 Dec 23 09:21 lib
drwx------  2 root root 4096 Dec 23 09:21 lost+found
drwx------  4 root root 4096 Dec 23 09:21 media
drwx------  2 root root 4096 Dec 23 09:21 mnt
drwx------  2 root root 4096 Dec 23 09:21 opt
dr-x------  2 root root 4096 Dec 23 09:21 proc
drwx------  2 root root 4096 Dec 23 09:21 root
drwx------  2 root root 4096 Dec 23 09:21 run
drwx------  2 root root 4096 Dec 23 09:21 sbin
drwx------  2 root root 4096 Dec 23 09:21 selinux
drwx------  2 root root 4096 Dec 23 09:21 srv
dr-x------  2 root root 4096 Dec 23 09:21 sys
drwx------  2 root root 4096 Dec 23 09:21 tmp
drwx------  2 root root 4096 Dec 23 09:21 usr
drwx------  2 root root 4096 Dec 23 09:21 var

    Keine Auffälligkeiten, so weit. Der dmesg sieht auch unauffällig aus.

    Armbian Image

    Hardware

    • ROCKPro64 v2.0 4GB RAM
    • PCIe SATA-Karte
    • 1TB 2,5 Zoll HDD
    • 240GB SSD
    • Boot erfolgt von SD-Karte

    Software

    Welcome to ARMBIAN 5.67.181217 nightly Debian GNU/Linux 9 (stretch) 4.4.167-rockchip64

    So, gestartet. Mit lspci -vvv mal nach dem rechten sehen.

    root@rockpro64:~# lspci -vvv
00:00.0 PCI bridge: Device 1d87:0100 (prog-if 00 [Normal decode])
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort+ <MAbort+ >SERR+ <PERR+ INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 224
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 00000000-00000fff
	Memory behind bridge: fa000000-fa0fffff
	Prefetchable memory behind bridge: 00000000-000fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [80] Power Management version 3
		Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME+
	Capabilities: [90] MSI: Enable+ Count=1/1 Maskable+ 64bit+
		Address: 00000000fee30040  Data: 0000
		Masking: 00000000  Pending: 00000000
	Capabilities: [b0] MSI-X: Enable- Count=1 Masked-
		Vector table: BAR=0 offset=00000000
		PBA: BAR=0 offset=00000008
	Capabilities: [c0] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 256 bytes, PhantFunc 0
			ExtTag- RBE+
		DevCtl:	Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #0, Speed 5GT/s, Width x4, ASPM L1, Exit Latency L0s <256ns, L1 <8us
			ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt+ AutBWInt+
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
			Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
			Control: AttnInd Off, PwrInd Off, Power+ Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL+ CmdCplt- PresDet- Interlock-
			Changed: MRL- PresDet- LinkState-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
		DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR+, OBFF Via message ARIFwd+
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [100 v2] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		AERCap:	First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
	Capabilities: [274 v1] Transaction Processing Hints
		Interrupt vector mode supported
		Device specific mode supported
		Steering table in TPH capability structure
	Kernel driver in use: pcieport

01:00.0 SATA controller: ASMedia Technology Inc. ASM1062 Serial ATA Controller (rev 02) (prog-if 01 [AHCI 1.0])
	Subsystem: ASMedia Technology Inc. ASM1062 Serial ATA Controller
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 225
	Region 0: I/O ports at <unassigned> [disabled]
	Region 1: I/O ports at <unassigned> [disabled]
	Region 2: I/O ports at <unassigned> [disabled]
	Region 3: I/O ports at <unassigned> [disabled]
	Region 4: I/O ports at <unassigned> [disabled]
	Region 5: Memory at fa010000 (32-bit, non-prefetchable) [size=512]
	[virtual] Expansion ROM at fa000000 [disabled] [size=64K]
	Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
		Address: fee30040  Data: 0000
	Capabilities: [78] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [80] Express (v2) Legacy Endpoint, MSI 00
		DevCap:	MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #1, Speed 5GT/s, Width x1, ASPM not supported, Exit Latency L0s unlimited, L1 <2us
			ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR-, OBFF Not Supported
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
	Capabilities: [100 v1] Virtual Channel
		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
		Arb:	Fixed- WRR32- WRR64- WRR128-
		Ctrl:	ArbSelect=Fixed
		Status:	InProgress-
		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
			Status:	NegoPending- InProgress-
	Kernel driver in use: ahci

    Festplatte suchen mit fdisk -l

    Disk /dev/sda: 223.6 GiB, 240057409536 bytes, 468862128 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0xaa1a7c28

Device     Boot Start       End   Sectors   Size Id Type
/dev/sda1       32768 468860927 468828160 223.6G 83 Linux

    Die Platte mal eben mounten

    root@rockpro64:~# mount /dev/sda1 /mnt
root@rockpro64:~# ls -la /mnt
total 88
drwxr-xr-x 22 root root 4096 Dec 23 09:04 .
drwxr-xr-x 22 root root 4096 Dec 23 09:04 ..
drwxr-xr-x  2 root root 4096 Dec  2 00:05 bin
drwxr-xr-x  3 root root 4096 Dec 23 09:21 boot
drwxr-xr-x  2 root root 4096 Dec 23 09:19 dev
drwxr-xr-x 86 root root 4096 Dec 23 09:21 etc
drwx------  2 root root 4096 Dec 23 09:21 home
drwx------  2 root root 4096 Dec 23 09:21 lib
drwx------  2 root root 4096 Dec 23 09:21 lost+found
drwx------  4 root root 4096 Dec 23 09:21 media
drwx------  2 root root 4096 Dec 23 09:21 mnt
drwx------  2 root root 4096 Dec 23 09:21 opt
dr-x------  2 root root 4096 Dec 23 09:21 proc
drwx------  2 root root 4096 Dec 23 09:21 root
drwx------  2 root root 4096 Dec 23 09:21 run
drwx------  2 root root 4096 Dec 23 09:21 sbin
drwx------  2 root root 4096 Dec 23 09:21 selinux
drwx------  2 root root 4096 Dec 23 09:21 srv
dr-x------  2 root root 4096 Dec 23 09:21 sys
drwx------  2 root root 4096 Dec 23 09:21 tmp
drwx------  2 root root 4096 Dec 23 09:21 usr
drwx------  2 root root 4096 Dec 23 09:21 var

    Fazit

    Auch hier kann ich berichten, das es mit beiden Images problemlos läuft. Auch hier nochmal die Vermutung, wenn ihr Probleme habt, dann schaut Euch mal die Stromversorgung an, vor allen Dingen wenn ihr 3,5 Zoll Festplatten einsetzt.

    Hat mal wieder Spaß gemacht zu testen, jetzt werde ich mein NAS mal umbauen (siehe ersten Teil).

    Im Fediverse -> @FrankM@nrw.social

    1. NanoPi R5S
    2. Quartz64 Model B, 4GB RAM
    3. Quartz64 Model A, 4GB RAM
    4. RockPro64 v2.1
    0
  • W

    Hmm, bei mir ist die Ausgabe von lspci komplett leer:

    uname -a
Linux rockpro64 4.20.0-1083-ayufan-g686e1f1aa461 #ayufan SMP PREEMPT Sun Dec 30 13:42:26 UTC 2018 aarch64 GNU/Linux
rock64@rockpro64:~$ sudo lspci -vvv

    Hast du eine Idee woran das liegen kann?

    0
  • FrankMF

    @wombat Welche PCIe-Karte probierst du aus?

    Ich habe viele Posts gelesen, das viele User Probleme haben PCIe Karten ans Laufen zu bekommen. Die zwei von Pine64 verkauften Karten, sollten mit Kamils Image laufen.

    Den 4.20er von Kamil habe ich nicht getestet, kann ich aber gerne mal machen.

    Im Fediverse -> @FrankM@nrw.social

    1. NanoPi R5S
    2. Quartz64 Model B, 4GB RAM
    3. Quartz64 Model A, 4GB RAM
    4. RockPro64 v2.1
    0
  • W

    @FrankM Ich versuche eine Telit LM960 LTE Karte mit einem mPCIe auf PCIe Adapter zum Laufen zu bekommen.

    Ich habe weder unter armbian, noch unter Debian Stretch sowohl mit rockchip als auch mainline 4.20 Kernel irgendwas am pcie bus gesehen.
    Der Delock Adapter hat auch eine Status LED - diese leuchtet aber nicht. Da ich die Karte vorher noch nie verwendet habe und aktuell auch nirgendwo anders testen kann, vermute ich einfach mal, dass die LED an sich leuten würde, wenn Strom auf dem Bus hängt, aber das kann ich beim Hersteller nochmal nachfragen.
    Laut Hersteller sind keine Treiber notwendig, da es ein passiver Adapter ist.

    Müsste ich nicht an sich auch ohne PCIe Karte das Rockchip device sehen? Wenn ich das im mainline Kernel richtig sehe, ist pcie0 per default deaktiviert?

    0
  • W

    Die dmesg Ausgabe mit 4.4 kernel ist hier: https://pastebin.com/FHMGRgVG
    Der mit 4.20 Kernel hier: https://pastebin.com/vZw0LhBN

    0
  • FrankMF

    Drei Fragen

    • Welchen RockPro64 hast du? Version und Speicher.
    • Du bootest von wo? spi, sdkarte....
    • Welche Erweiterungskarte nutzt du?

    Im Fediverse -> @FrankM@nrw.social

    1. NanoPi R5S
    2. Quartz64 Model B, 4GB RAM
    3. Quartz64 Model A, 4GB RAM
    4. RockPro64 v2.1
    0
  • W

    @FrankM

    0
  • FrankMF

    Die Verlinkung hatte ich überlesen, sorry.

    Es gibt nur eine Handvoll Karten, die im PCIe Port funktionieren. Warum, kann ich dir leider nicht beantworten. Es liegt aber mit Sicherheit an falschen Einstellungen im Kernel und an fehlenden Treibern. Ich habe hier auch eine andere Karte rumliegen, die erzeugt immer nur eine Kernel Panic 😞

    In diesem Thread steht einiges was geht und was nicht.
    https://forum.pine64.org/showthread.php?tid=6459

    Im Fediverse -> @FrankM@nrw.social

    1. NanoPi R5S
    2. Quartz64 Model B, 4GB RAM
    3. Quartz64 Model A, 4GB RAM
    4. RockPro64 v2.1
    0

  • FrankMF

    Mainline 5.4.x

    Images
    2
    0 Stimmen
    2 Beiträge
    346 Aufrufe
    FrankMF

    Bootet bei mir weder von USB3-SSD noch von SD-Karte.

    USB3-SSD -> https://pastebin.com/QAS92sme
    SD-Karte -> https://pastebin.com/Bsr3WLJ7

  • FrankMF

    Armbian für den ROCKPro64

    Angeheftet Armbian
    1
    0 Stimmen
    1 Beiträge
    529 Aufrufe
    Niemand hat geantwortet
  • FrankMF

    Benchmark

    ROCKPro64
    1
    0 Stimmen
    1 Beiträge
    446 Aufrufe
    Niemand hat geantwortet
  • FrankMF

    Freier Linux GPU Treiber

    ROCKPro64
    1
    0 Stimmen
    1 Beiträge
    500 Aufrufe
    Niemand hat geantwortet
  • FrankMF

    Ubuntu Bionic - Namen der Interfaces umstellen

    ROCKPro64
    1
    0 Stimmen
    1 Beiträge
    569 Aufrufe
    Niemand hat geantwortet
  • FrankMF

    Mainline Kernel 4.18.0-rc3

    Linux
    1
    0 Stimmen
    1 Beiträge
    961 Aufrufe
    Niemand hat geantwortet
  • FrankMF

    Benchmark Mainline 4.17.0-rc6

    Verschoben Archiv
    4
    0 Stimmen
    4 Beiträge
    992 Aufrufe
    FrankMF
    iozone 5GT/s x2 rock64@rockpro64:/mnt$ sudo iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Iozone: Performance Test of File I/O Version $Revision: 3.429 $ Compiled for 64 bit mode. Build: linux Contributors:William Norcott, Don Capps, Isom Crawford, Kirby Collins Al Slater, Scott Rhine, Mike Wisner, Ken Goss Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR, Randy Dunlap, Mark Montague, Dan Million, Gavin Brebner, Jean-Marc Zucconi, Jeff Blomberg, Benny Halevy, Dave Boone, Erik Habbinga, Kris Strecker, Walter Wong, Joshua Root, Fabrice Bacchella, Zhenghua Xue, Qin Li, Darren Sawyer, Vangel Bojaxhi, Ben England, Vikentsi Lapa. Run began: Sat Jun 16 06:34:43 2018 Include fsync in write timing O_DIRECT feature enabled Auto Mode File size set to 102400 kB Record Size 4 kB Record Size 16 kB Record Size 512 kB Record Size 1024 kB Record Size 16384 kB Command line used: iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Output is in kBytes/sec Time Resolution = 0.000001 seconds. Processor cache size set to 1024 kBytes. Processor cache line size set to 32 bytes. File stride size set to 17 * record size. random random bkwd record stride kB reclen write rewrite read reread read write read rewrite read fwrite frewrite fread freread 102400 4 48672 104754 115838 116803 47894 103606 102400 16 168084 276437 292660 295458 162550 273703 102400 512 566572 597648 580005 589209 534508 597007 102400 1024 585621 624443 590545 599177 569452 630098 102400 16384 504871 754710 765558 780592 777696 753426 iozone test complete. 2,5GT/s x2 rock64@rockpro64:/mnt$ sudo iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Iozone: Performance Test of File I/O Version $Revision: 3.429 $ Compiled for 64 bit mode. Build: linux Contributors:William Norcott, Don Capps, Isom Crawford, Kirby Collins Al Slater, Scott Rhine, Mike Wisner, Ken Goss Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR, Randy Dunlap, Mark Montague, Dan Million, Gavin Brebner, Jean-Marc Zucconi, Jeff Blomberg, Benny Halevy, Dave Boone, Erik Habbinga, Kris Strecker, Walter Wong, Joshua Root, Fabrice Bacchella, Zhenghua Xue, Qin Li, Darren Sawyer, Vangel Bojaxhi, Ben England, Vikentsi Lapa. Run began: Sun Jun 17 06:54:02 2018 Include fsync in write timing O_DIRECT feature enabled Auto Mode File size set to 102400 kB Record Size 4 kB Record Size 16 kB Record Size 512 kB Record Size 1024 kB Record Size 16384 kB Command line used: iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Output is in kBytes/sec Time Resolution = 0.000001 seconds. Processor cache size set to 1024 kBytes. Processor cache line size set to 32 bytes. File stride size set to 17 * record size. random random bkwd record stride kB reclen write rewrite read reread read write read rewrite read fwrite frewrite fread freread 102400 4 49420 91310 102658 103415 47023 90099 102400 16 138141 202088 224648 225918 141642 202457 102400 512 335055 347517 375096 378596 364668 350005 102400 1024 345508 354999 378947 382733 375315 354783 102400 16384 306262 383155 424403 429423 428670 377476 iozone test complete.
  • FrankMF

    ROCKPro64 - Platinenerkundung

    ROCKPro64
    1
    0 Stimmen
    1 Beiträge
    601 Aufrufe
    Niemand hat geantwortet