Skip to content

Kernel 4.4.x

Angeheftet Images

  • ROCKPro64 - Kernel 5.3.0-rc4-1117 angetestet!

    ROCKPro64
    1
    0 Stimmen
    1 Beiträge
    380 Aufrufe
    Niemand hat geantwortet
  • ROCKPro64 - WLan-Antennen

    Hardware
    1
    0 Stimmen
    1 Beiträge
    274 Aufrufe
    Niemand hat geantwortet
  • ROCKPro64 - Das erste Mal

    Angeheftet Verschoben Hardware
    5
    1 Stimmen
    5 Beiträge
    865 Aufrufe
    FrankMF

    Ich kann heute die Fragen aller Fragen beantworten 🙂

    Damit ist leider die Frage immer noch unbeantwortet ob WLan und PCIe zusammen nutzbar ist!! Es geht!!

    Ich habe von MrFixit ein Testimage der RecalBox, benutzt das selbe Debian wie oben. Die Tage konnte man im IRC verfolgen, wie man dem Grundproblem näher kam und wohl einen Fix gebastelt hat, damit beides zusammen funktioniert. Mr.Fixit hat das in RecalBox eingebaut und ich durfte testen.

    # ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue qlen 1 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP8000> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 62:03:b0:d6:dc:b3 brd ff:ff:ff:ff:ff:ff 3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP8000> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether ac:83:f3:e6:1f:b2 brd ff:ff:ff:ff:ff:ff inet 192.168.178.27/24 brd 192.168.178.255 scope global wlan0 valid_lft forever preferred_lft forever inet6 2a02:908:1262:4680:ae83:f3ff:fee6:1fb2/64 scope global dynamic valid_lft 7145sec preferred_lft 3545sec inet6 fe80::ae83:f3ff:fee6:1fb2/64 scope link valid_lft forever preferred_lft forever # ls /mnt bin etc media recalbox sd.img test2.img boot home mnt root selinux tmp crypthome lib opt run srv usr dev lost+found proc sbin sys var # fdisk BusyBox v1.27.2 (2019-02-01 22:43:19 EST) multi-call binary. Usage: fdisk [-ul] [-C CYLINDERS] [-H HEADS] [-S SECTORS] [-b SSZ] DISK Change partition table -u Start and End are in sectors (instead of cylinders) -l Show partition table for each DISK, then exit -b 2048 (for certain MO disks) use 2048-byte sectors -C CYLINDERS Set number of cylinders/heads/sectors -H HEADS Typically 255 -S SECTORS Typically 63 # fdisk -l Disk /dev/mmcblk0: 15 GB, 15931539456 bytes, 31116288 sectors 486192 cylinders, 4 heads, 16 sectors/track Units: cylinders of 64 * 512 = 32768 bytes Device Boot StartCHS EndCHS StartLBA EndLBA Sectors Size Id Type /dev/mmcblk0p1 * 2,10,9 10,50,40 32768 163839 131072 64.0M c Win95 FAT32 (LBA) Partition 1 does not end on cylinder boundary /dev/mmcblk0p2 * 16,81,2 277,102,17 262144 4456447 4194304 2048M 83 Linux Partition 2 does not end on cylinder boundary /dev/mmcblk0p3 277,102,18 1023,254,63 4456448 31115263 26658816 12.7G 83 Linux Partition 3 does not end on cylinder boundary Disk /dev/nvme0n1: 233 GB, 250059350016 bytes, 488397168 sectors 2543735 cylinders, 12 heads, 16 sectors/track Units: cylinders of 192 * 512 = 98304 bytes Device Boot StartCHS EndCHS StartLBA EndLBA Sectors Size Id Type /dev/nvme0n1p1 1,0,1 907,11,16 2048 488397167 488395120 232G 83 Linux #

    Oben sieht man eine funktionierende WLan-Verbindung, das LAN-Kabel war entfernt. Unten sieht man die PCIe NVMe SSD, gemountet nach /mnt und Inhaltsausgabe.

    Das sollte beweisen, das der Ansatz der Lösung funktioniert. Leider kann ich nicht sagen, das es zum jetzigen Zeitpunkt stabil läuft. Ich habe einfach so Reboots, kann den Fehler aktuell aber nicht fangen. Mal sehen ob ich noch was finde.

    Aber, es ist ein Anfang!

  • Kamil's 4.20.x

    ROCKPro64
    1
    0 Stimmen
    1 Beiträge
    647 Aufrufe
    Niemand hat geantwortet
  • ROCKPro64 - PCIe SATA-Karte macht immer mal Probleme

    ROCKPro64
    2
    0 Stimmen
    2 Beiträge
    494 Aufrufe
    FrankMF

    Das ist das Ergebnis des Stresstests 😞

    [ 2461.489468] ata2.00: exception Emask 0x10 SAct 0xffffffff SErr 0x400000 action 0x6 frozen [ 2461.490206] ata2.00: irq_stat 0x08000000, interface fatal error [ 2461.490732] ata2: SError: { Handshk } [ 2461.491062] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.491532] ata2.00: cmd 61/40:00:f8:a6:64/05:00:84:00:00/40 tag 0 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.492993] ata2.00: status: { DRDY } [ 2461.493327] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.493796] ata2.00: cmd 61/c0:08:38:ac:64/03:00:84:00:00/40 tag 1 ncq dma 491520 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.495181] ata2.00: status: { DRDY } [ 2461.495507] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.496276] ata2.00: cmd 61/c0:10:a0:f5:64/02:00:84:00:00/40 tag 2 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.497697] ata2.00: status: { DRDY } [ 2461.498029] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.498497] ata2.00: cmd 61/40:18:60:f8:64/05:00:84:00:00/40 tag 3 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.499886] ata2.00: status: { DRDY } [ 2461.500213] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.500681] ata2.00: cmd 61/c0:20:a0:fd:64/02:00:84:00:00/40 tag 4 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.502087] ata2.00: status: { DRDY } [ 2461.502416] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.502884] ata2.00: cmd 61/40:28:60:00:65/05:00:84:00:00/40 tag 5 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.505026] ata2.00: status: { DRDY } [ 2461.505378] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.505852] ata2.00: cmd 61/c0:30:a0:05:65/02:00:84:00:00/40 tag 6 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.507244] ata2.00: status: { DRDY } [ 2461.507572] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.508040] ata2.00: cmd 61/40:38:60:08:65/05:00:84:00:00/40 tag 7 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.509472] ata2.00: status: { DRDY } [ 2461.509808] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.510277] ata2.00: cmd 61/a0:40:a0:0d:65/02:00:84:00:00/40 tag 8 ncq dma 344064 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.511667] ata2.00: status: { DRDY } [ 2461.511994] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.512461] ata2.00: cmd 61/40:48:00:20:66/05:00:84:00:00/40 tag 9 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.514503] ata2.00: status: { DRDY } [ 2461.514850] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.515322] ata2.00: cmd 61/40:50:00:28:66/05:00:84:00:00/40 tag 10 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.516721] ata2.00: status: { DRDY } [ 2461.517084] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.517562] ata2.00: cmd 61/c0:58:40:2d:66/02:00:84:00:00/40 tag 11 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.519253] ata2.00: status: { DRDY } [ 2461.519595] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.520066] ata2.00: cmd 61/40:60:f8:9e:64/05:00:84:00:00/40 tag 12 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.521504] ata2.00: status: { DRDY } [ 2461.521840] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.522309] ata2.00: cmd 61/c0:68:38:a4:64/02:00:84:00:00/40 tag 13 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.523706] ata2.00: status: { DRDY } [ 2461.524033] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.524501] ata2.00: cmd 61/40:70:f8:af:64/05:00:84:00:00/40 tag 14 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.525925] ata2.00: status: { DRDY } [ 2461.526256] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.526725] ata2.00: cmd 61/c0:78:38:b5:64/02:00:84:00:00/40 tag 15 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.528122] ata2.00: status: { DRDY } [ 2461.528449] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.528939] ata2.00: cmd 61/40:80:f8:b7:64/05:00:84:00:00/40 tag 16 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.530339] ata2.00: status: { DRDY } [ 2461.530667] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.531136] ata2.00: cmd 61/c0:88:38:bd:64/02:00:84:00:00/40 tag 17 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.532532] ata2.00: status: { DRDY } [ 2461.532880] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.533357] ata2.00: cmd 61/40:90:f8:bf:64/05:00:84:00:00/40 tag 18 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.534754] ata2.00: status: { DRDY } [ 2461.535081] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.535549] ata2.00: cmd 61/c0:98:38:c5:64/02:00:84:00:00/40 tag 19 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.536970] ata2.00: status: { DRDY } [ 2461.537301] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.537769] ata2.00: cmd 61/40:a0:f8:c7:64/05:00:84:00:00/40 tag 20 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.539165] ata2.00: status: { DRDY } [ 2461.539491] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.539960] ata2.00: cmd 61/c0:a8:38:cd:64/02:00:84:00:00/40 tag 21 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.541381] ata2.00: status: { DRDY } [ 2461.541713] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.542182] ata2.00: cmd 61/40:b0:f8:cf:64/05:00:84:00:00/40 tag 22 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.543577] ata2.00: status: { DRDY } [ 2461.543905] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.544374] ata2.00: cmd 61/40:b8:f8:d7:64/05:00:84:00:00/40 tag 23 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.545790] ata2.00: status: { DRDY } [ 2461.546120] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.546589] ata2.00: cmd 61/c0:c0:38:dd:64/02:00:84:00:00/40 tag 24 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.547987] ata2.00: status: { DRDY } [ 2461.548314] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.548782] ata2.00: cmd 61/a8:c8:f8:df:64/05:00:84:00:00/40 tag 25 ncq dma 741376 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.550198] ata2.00: status: { DRDY } [ 2461.550530] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.550999] ata2.00: cmd 61/c0:d0:a0:e5:64/02:00:84:00:00/40 tag 26 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.552396] ata2.00: status: { DRDY } [ 2461.552723] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.553208] ata2.00: cmd 61/40:d8:60:e8:64/05:00:84:00:00/40 tag 27 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.554607] ata2.00: status: { DRDY } [ 2461.554935] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.555404] ata2.00: cmd 61/c0:e0:a0:ed:64/02:00:84:00:00/40 tag 28 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.556800] ata2.00: status: { DRDY } [ 2461.557145] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.557617] ata2.00: cmd 61/40:e8:60:f0:64/05:00:84:00:00/40 tag 29 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.559012] ata2.00: status: { DRDY } [ 2461.559340] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.559807] ata2.00: cmd 61/c0:f0:38:d5:64/02:00:84:00:00/40 tag 30 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.561221] ata2.00: status: { DRDY } [ 2461.561552] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.562021] ata2.00: cmd 61/c0:f8:40:25:66/02:00:84:00:00/40 tag 31 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.563416] ata2.00: status: { DRDY } [ 2461.563752] ata2: hard resetting link [ 2471.561504] ata2: softreset failed (1st FIS failed) [ 2471.561959] ata2: hard resetting link [ 2481.560785] ata2: softreset failed (1st FIS failed) [ 2481.561238] ata2: hard resetting link [ 2516.561654] ata2: softreset failed (1st FIS failed) [ 2516.562109] ata2: limiting SATA link speed to 3.0 Gbps [ 2516.562113] ata2: hard resetting link [ 2521.561261] ata2: softreset failed (1st FIS failed) [ 2521.561715] ata2: reset failed, giving up [ 2521.562074] ata2.00: disabled [ 2521.562575] ata2: EH complete [ 2521.562677] sd 1:0:0:0: [sdb] tag#18 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.562686] sd 1:0:0:0: [sdb] tag#18 CDB: opcode=0x35 35 00 00 00 00 00 00 00 00 00 [ 2521.562701] print_req_error: I/O error, dev sdb, sector 0 [ 2521.562791] sd 1:0:0:0: [sdb] tag#20 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.562802] sd 1:0:0:0: [sdb] tag#19 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.562873] sd 1:0:0:0: [sdb] tag#19 CDB: opcode=0x2a 2a 00 84 66 25 40 00 02 c0 00 [ 2521.562888] print_req_error: I/O error, dev sdb, sector 2221286720 [ 2521.563107] sd 1:0:0:0: [sdb] tag#21 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.563126] sd 1:0:0:0: [sdb] tag#21 CDB: opcode=0x2a 2a 00 84 64 f0 60 00 05 40 00 [ 2521.563138] print_req_error: I/O error, dev sdb, sector 2221207648 [ 2521.563422] sd 1:0:0:0: [sdb] tag#22 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.563772] sd 1:0:0:0: [sdb] tag#20 CDB: opcode=0x2a 2a 00 84 64 d5 38 00 02 c0 00 [ 2521.564326] print_req_error: I/O error, dev sdb, sector 2221200696 [ 2521.564337] sd 1:0:0:0: [sdb] tag#22 CDB: opcode=0x2a 2a 00 84 64 ed a0 00 02 c0 00 [ 2521.564896] print_req_error: I/O error, dev sdb, sector 2221206944 [ 2521.565088] sd 1:0:0:0: [sdb] tag#26 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.565469] sd 1:0:0:0: [sdb] tag#26 CDB: opcode=0x2a 2a 00 84 64 dd 38 00 02 c0 00 [ 2521.565483] print_req_error: I/O error, dev sdb, sector 2221202744 [ 2521.565610] sd 1:0:0:0: [sdb] tag#23 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.566056] sd 1:0:0:0: [sdb] tag#23 CDB: opcode=0x2a 2a 00 84 64 e8 60 00 05 40 00 [ 2521.566069] print_req_error: I/O error, dev sdb, sector 2221205600 [ 2521.566183] sd 1:0:0:0: [sdb] tag#29 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.566641] sd 1:0:0:0: [sdb] tag#29 CDB: opcode=0x2a 2a 00 84 64 cd 38 00 02 c0 00 [ 2521.566654] print_req_error: I/O error, dev sdb, sector 2221198648 [ 2521.566954] sd 1:0:0:0: [sdb] tag#24 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.567224] sd 1:0:0:0: [sdb] tag#24 CDB: opcode=0x2a 2a 00 84 64 e5 a0 00 02 c0 00 [ 2521.567237] print_req_error: I/O error, dev sdb, sector 2221204896 [ 2521.567459] sd 1:0:0:0: [sdb] tag#30 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.567809] sd 1:0:0:0: [sdb] tag#30 CDB: opcode=0x2a 2a 00 84 64 c7 f8 00 05 40 00 [ 2521.567821] print_req_error: I/O error, dev sdb, sector 2221197304 [ 2521.584903] md: super_written gets error=10 [ 2521.585306] md/raid1:md0: Disk failure on dm-1, disabling device. md/raid1:md0: Operation continuing on 1 devices. [ 2526.581450] scsi_io_completion_action: 41779 callbacks suppressed [ 2526.581461] sd 1:0:0:0: [sdb] tag#27 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.581467] sd 1:0:0:0: [sdb] tag#27 CDB: opcode=0x2a 2a 00 84 66 7d 50 00 00 01 00 [ 2526.581469] print_req_error: 41780 callbacks suppressed [ 2526.581471] print_req_error: I/O error, dev sdb, sector 2221309264 [ 2526.582524] sd 1:0:0:0: [sdb] tag#28 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.582530] sd 1:0:0:0: [sdb] tag#28 CDB: opcode=0x2a 2a 00 84 66 7d 51 00 00 01 00 [ 2526.582534] print_req_error: I/O error, dev sdb, sector 2221309265 [ 2526.583366] sd 1:0:0:0: [sdb] tag#29 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.583370] sd 1:0:0:0: [sdb] tag#29 CDB: opcode=0x2a 2a 00 84 66 7d 52 00 00 01 00 [ 2526.583373] print_req_error: I/O error, dev sdb, sector 2221309266 [ 2526.584113] sd 1:0:0:0: [sdb] tag#30 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.584117] sd 1:0:0:0: [sdb] tag#30 CDB: opcode=0x2a 2a 00 84 66 7d 53 00 00 01 00 [ 2526.584119] print_req_error: I/O error, dev sdb, sector 2221309267 [ 2526.584960] sd 1:0:0:0: [sdb] tag#0 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.584968] sd 1:0:0:0: [sdb] tag#0 CDB: opcode=0x2a 2a 00 84 66 7d 54 00 00 01 00 [ 2526.584971] print_req_error: I/O error, dev sdb, sector 2221309268 [ 2526.585765] sd 1:0:0:0: [sdb] tag#1 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.585769] sd 1:0:0:0: [sdb] tag#1 CDB: opcode=0x2a 2a 00 84 66 7d 55 00 00 01 00 [ 2526.585772] print_req_error: I/O error, dev sdb, sector 2221309269 [ 2526.586461] sd 1:0:0:0: [sdb] tag#2 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.586465] sd 1:0:0:0: [sdb] tag#2 CDB: opcode=0x2a 2a 00 84 66 7d 56 00 00 01 00 [ 2526.586468] print_req_error: I/O error, dev sdb, sector 2221309270 [ 2526.587144] sd 1:0:0:0: [sdb] tag#3 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.587148] sd 1:0:0:0: [sdb] tag#3 CDB: opcode=0x2a 2a 00 84 66 7d 57 00 00 01 00 [ 2526.587150] print_req_error: I/O error, dev sdb, sector 2221309271 [ 2526.587734] sd 1:0:0:0: [sdb] tag#4 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.587737] sd 1:0:0:0: [sdb] tag#4 CDB: opcode=0x2a 2a 00 84 66 7d 58 00 00 01 00 [ 2526.587739] print_req_error: I/O error, dev sdb, sector 2221309272 [ 2526.588320] sd 1:0:0:0: [sdb] tag#5 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.588323] sd 1:0:0:0: [sdb] tag#5 CDB: opcode=0x2a 2a 00 84 66 7d 59 00 00 01 00 [ 2526.588325] print_req_error: I/O error, dev sdb, sector 2221309273

    Und, wieder eine Platte im Raid1 verloren

    rock64@rockpro64v_2_1:~$ cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid1 dm-1[2](F) dm-0[1] 1953379392 blocks super 1.2 [2/1] [_U] bitmap: 5/15 pages [20KB], 65536KB chunk unused devices: <none>

    Leider habe ich nicht die Kenntnisse um zu erkennen, woran das liegt.

  • ROCKPro64 - RP64.GPIO

    Angeheftet Verschoben Hardware
    6
    0 Stimmen
    6 Beiträge
    6k Aufrufe
    FrankMF

    Hallo zusammen,

    da ich weiß das dieser Artikel recht beliebt ist, wollen wir den heute mal aktualisieren. Vieles aus den vorherigen Beiträgen passt noch. Es gibt aber kleine Anpassungen.

    Hardware ROCKPro64v21. 2GB RAM Software Kamils Release 0.10.9 Linux rockpro64 5.6.0-1132-ayufan-g81043e6e109a #ayufan SMP Tue Apr 7 10:07:35 UTC 2020 aarch64 GNU/Linux Installation apt install python

    Danach laden wir das Projekt

    git clone https://github.com/Leapo/Rock64-R64.GPIO

    PIN Nummern anpassen

    cd Rock64-R64.GPIO/R64 nano _GPIO.py

    Datei ergänzen

    # Define GPIO arrays #ROCK_valid_channels = [27, 32, 33, 34, 35, 36, 37, 38, 64, 65, 67, 68, 69, 76, 79, 80, 81, 82, 83, 84, 85, 86, 87, 88, 89, 96, 97, 98, 100, 101, 102, 103, 104] #BOARD_to_ROCK = [0, 0, 0, 89, 0, 88, 0, 0, 64, 0, 65, 0, 67, 0, 0, 100, 101, 0, 102, 97, 0, 98, 103, 96, 104, 0, 76, 68, 69, 0, 0, 0, 38, 32, 0, 33, 37, 34, 36, 0, 35, 0, 0, 81, 82, 87, 83, 0, 0, 80, 79, 85, 84, 27, 86, 0, 0, 0, 0, 0, 0, 89, 88] #BCM_to_ROCK = [68, 69, 89, 88, 81, 87, 83, 76, 104, 98, 97, 96, 38, 32, 64, 65, 37, 80, 67, 33, 36, 35, 100, 101, 102, 103, 34, 82] ROCK_valid_channels = [52,53,152,54,50,33,48,39,41,43,155,156,125,122,121,148,147,120,36,149,153,42,45,44,124,126,123,127] BOARD_to_ROCK = [0,0,0,52,0,53,0,152,148,0,147,54,120,50,0,33,36,0,149,48,0,39,153,41,42,0,45,43,44,155,0,156,124,125,0,122,126,121,123,0,127] BCM_to_ROCK = [43,44,52,53,152,155,156,45,42,39,48,41,124,125,148,147,124,54,120,122,123,127,33,36,149,153,121,50]

    Abspeichern.

    Datei test.py anlegen

    nano test.py

    Inhalt

    #!/usr/bin/env python # Frank Mankel, 2018, LGPLv3 License # Rock 64 GPIO Library for Python # Thanks Allison! Thanks smartdave! import R64.GPIO as GPIO from time import sleep print("Output Test R64.GPIO Module...") # Set Variables var_gpio_out = 156 var_gpio_in = 155 # GPIO Setup GPIO.setwarnings(True) GPIO.setmode(GPIO.ROCK) GPIO.setup(var_gpio_out, GPIO.OUT, initial=GPIO.HIGH) # Set up GPIO as an output, with an initial state of HIGH GPIO.setup(var_gpio_in, GPIO.IN, pull_up_down=GPIO.PUD_UP) # Set up GPIO as an input, pullup enabled # Test Output print("") print("Testing GPIO Input/Output:") while True: var_gpio_state_in = GPIO.input(var_gpio_in) var_gpio_state = GPIO.input(var_gpio_out) # Return State of GPIO if var_gpio_state == 0 and var_gpio_state_in == 1: GPIO.output(var_gpio_out,GPIO.HIGH) # Set GPIO to HIGH print("Input State: " + str(var_gpio_state_in)) # Print results print("Output State IF : " + str(var_gpio_state)) # Print results else: GPIO.output(var_gpio_out,GPIO.LOW) # Set GPIO to LOW print("Input State: " + str(var_gpio_state_in)) # Print results print("Output State ELSE: " + str(var_gpio_state)) # Print results sleep(0.5) exit() Beispiel

    Bild Text

    Wenn der Taster im Bild betätigt wird, soll die LED blinken.

    Wir benutzen folgende Ein- Augänge des ROCKPro64.

    # Set Variables var_gpio_out = 156 var_gpio_in = 155

    Das heißt:

    an Pin 1 (3,3V) kommt eine Strippe des Tasters an Pin 29 (Input) kommt eine Strippe des Tasters an Pin 31 (Output) kommt der Plus-Pol der LED an Pin 39 (GND) kommt der Minus-Pol der LED

    Somit wird auf den Eingang (Pin 29) bei Betätigung des Tasters 3,3 Volt angelegt. Damit wird dann der Eingang als High (1) erkannt. Die LED wird über den Ausgang (Pin 31) gesteuert.

    Starten kann man das Script mit

    python test.py

  • ROCKPro64 - kein WLan-Modul möglich?

    ROCKPro64
    4
    0 Stimmen
    4 Beiträge
    2k Aufrufe
    FrankMF

    Heute, 5 Monate später, kann ich bestätigen das WLan möglich ist 🙂 Getestet auf einem ROCKPro64 v2.1 mit 2GB RAM.

    Eine Vorabversion von Recalbox machte es das erste Mal für mich möglich das WLan zu benutzen. Bericht

    Und PCIe ist abgeschaltet im dts File.

    pcie-phy { compatible = "rockchip,rk3399-pcie-phy"; #phy-cells = <0x0>; rockchip,grf = <0x15>; clocks = <0x8 0x8a>; clock-names = "refclk"; resets = <0x8 0x87>; reset-names = "phy"; status = "disabled"; phandle = <0x8b>; }; pcie@f8000000 { compatible = "rockchip,rk3399-pcie"; #address-cells = <0x3>; #size-cells = <0x2>; aspm-no-l0s; clocks = <0x8 0xc5 0x8 0xc4 0x8 0x147 0x8 0xa0>; clock-names = "aclk", "aclk-perf", "hclk", "pm"; bus-range = <0x0 0x1f>; max-link-speed = <0x2>; linux,pci-domain = <0x0>; msi-map = <0x0 0x89 0x0 0x1000>; interrupts = <0x0 0x31 0x4 0x0 0x0 0x32 0x4 0x0 0x0 0x33 0x4 0x0>; interrupt-names = "sys", "legacy", "client"; #interrupt-cells = <0x1>; interrupt-map-mask = <0x0 0x0 0x0 0x7>; interrupt-map = <0x0 0x0 0x0 0x1 0x8a 0x0 0x0 0x0 0x0 0x2 0x8a 0x1 0x0 0x0 0x0 0x3 0x8a 0x2 0x0 0x0 0x0 0x4 0x8a 0x3>; phys = <0x8b>; phy-names = "pcie-phy"; ranges = <0x83000000 0x0 0xfa000000 0x0 0xfa000000 0x0 0x1e00000 0x81000000 0x0 0xfbe00000 0x0 0xfbe00000 0x0 0x100000>; reg = <0x0 0xf8000000 0x0 0x2000000 0x0 0xfd000000 0x0 0x1000000>; reg-names = "axi-base", "apb-base"; resets = <0x8 0x82 0x8 0x83 0x8 0x84 0x8 0x85 0x8 0x86 0x8 0x81 0x8 0x80>; reset-names = "core", "mgmt", "mgmt-sticky", "pipe", "pm", "pclk", "aclk"; status = "disabled";

    Also bleibt weiterhin ungeklärt, ob auch beides zusammen möglich ist. Also gleichzeitig das WLan-Modul und eine PCIe Karte.

  • Image 0.6.57 - NVMe paar Notizen

    Verschoben Archiv
    1
    0 Stimmen
    1 Beiträge
    651 Aufrufe
    Niemand hat geantwortet