Skip to content

ASRock N100M

Linux
9 2 2.2k
  • SATA Karte Marvell 88SE9230 Chipsatz

    Angeheftet Hardware hardware rockpro64
    19
    0 Stimmen
    19 Beiträge
    6k Aufrufe
    FrankMF
    Ok, es gibt noch eine andere Möglichkeit. Kamil hat mir noch ein wenig geholfen. Mit folgender Änderung werden die Platten gefunden. hmm, I had to add /etc/default/extlinux: libahci.skip_host_reset=1 Sieht dann so aus. # Configure timeout to choose the kernel # TIMEOUT="10" # Configure default kernel to boot: check all kernels in `/boot/extlinux/extlinux.conf` # DEFAULT="kernel-4.4.126-rockchip-ayufan-253" # Configure additional kernel configuration options APPEND="$APPEND root=LABEL=linux-root rootwait rootfstype=ext4 libahci.skip_host_reset=1" Danach waren die Platten zu sehen. root@rockpro64:/tmp/etc/default# blkid /dev/sda2: SEC_TYPE="msdos" LABEL_FATBOOT="boot-efi" LABEL="boot-efi" UUID="ABCD-FC7D" TYPE="vfat" PARTLABEL="boot_efi" PARTUUID="72e36967-4050-4bb3-8f8f-bf6755c38f28" /dev/sda3: LABEL="linux-boot" UUID="8e289a3e-0f9b-4da1-a147-51e03390637c" TYPE="ext4" PARTLABEL="linux_boot" PARTUUID="fe944fd2-3e42-4202-8a95-656e9bdb4be6" /dev/sda4: LABEL="linux-root" UUID="3e9513c6-dfd1-48c9-bee2-04bb5a153056" TYPE="ext4" PARTLABEL="linux_root" PARTUUID="d2d1dd88-030d-4f74-998f-7c9ce7d385d0" /dev/sdb2: SEC_TYPE="msdos" LABEL_FATBOOT="boot-efi" LABEL="boot-efi" UUID="56C9-F745" TYPE="vfat" PARTLABEL="boot_efi" PARTUUID="919c8f73-5f25-4a01-9072-3a5ed9a88ff2" /dev/sdb3: LABEL="linux-boot" UUID="23c19647-f4a1-4197-a877-f1bb03456bef" TYPE="ext4" PARTLABEL="linux_boot" PARTUUID="093d0cc0-d122-4dce-aeb5-4e266b4b7d9d" /dev/sdb4: LABEL="linux-root" UUID="f1c74331-8318-4ee8-a4f7-f0c169fb9944" TYPE="ext4" PARTLABEL="linux_root" PARTUUID="964ab457-58d5-40c4-bb02-dfd37bd2f0da" /dev/sda1: PARTLABEL="loader1" PARTUUID="37466429-e4a4-495c-b9a1-3f74625a3cae" /dev/sdb1: PARTLABEL="loader1" PARTUUID="33f692b3-54cb-4a37-b602-21a2baf32fa0" Aber auch hiermit ist ein Boot von der SATA Platte nicht möglich. Ich möchte hier noch was vom kamil zitieren. (11:44:09) ayufanWithPM: will look later, but this controller is tricky, also on x86 as well (11:44:16) ayufanWithPM: jms585 seems to be significantly more stable Evt. bekommt er das gefixt
  • Recover Button

    Hardware hardware rockpro64
    2
    2
    0 Stimmen
    2 Beiträge
    898 Aufrufe
    FrankMF
    Ich hab das mal ausprobiert. Den Recover Button so lange drücken, bis folgendes erscheint. In: serial@ff1a0000 Out: serial@ff1a0000 Err: serial@ff1a0000 Model: Pine64 RockPro64 rockchip_dnl_mode = 1 mode rockchip_dnl_mode = 2 mode rockchip_dnl_mode = 3 mode rockchip_dnl_mode = 4 mode entering maskrom mode... RKFlashTool clonen root@thinkpad:/home/frank/test# git clone https://github.com/rockchip-linux/rkflashtool Klone nach 'rkflashtool' ... remote: Counting objects: 663, done. remote: Total 663 (delta 0), reused 0 (delta 0), pack-reused 663 Empfange Objekte: 100% (663/663), 114.94 KiB | 0 bytes/s, Fertig. Löse Unterschiede auf: 100% (367/367), Fertig. In das Verzeichnis wechseln root@thinkpad:/home/frank/test# cd rkflashtool/ Inhalt root@thinkpad:/home/frank/test/rkflashtool# ls doc Makefile rkcrc.h rkflashtool.h rkparametersblock examples README rkflashall rkmisc rkunpack.c fixversion.sh release.sh rkflashloader rkpad rkunsign flashuboot rkcrc.c rkflashtool.c rkparameters version.h RKFlashtool bauen root@thinkpad:/home/frank/test/rkflashtool# make gcc -O2 -W -Wall -I/usr/include/libusb-1.0 rkflashtool.c -o rkflashtool -lusb-1.0 gcc -O2 -W -Wall -I/usr/include/libusb-1.0 rkcrc.c -o rkcrc -lusb-1.0 gcc -O2 -W -Wall -I/usr/include/libusb-1.0 rkunpack.c -o rkunpack -lusb-1.0 Ich habe ein USB-A to USB-A Kabel vom USB-C Port des ROCKPro64 zu meinem Notebook hergestellt. root@thinkpad:/home/frank/test/rkflashtool# sudo ./rkflashtool v rkflashtool: info: rkflashtool v5.2 rkflashtool: info: Detected RK3399... rkflashtool: info: interface claimed rkflashtool: info: MASK ROM MODE rkflashtool: info: chip version: -..- Ok, Verbindung steht. Eine Übersicht der Befehle root@thinkpad:/home/frank/test/rkflashtool# sudo ./rkflashtool rkflashtool: info: rkflashtool v5.2 rkflashtool: fatal: usage: rkflashtool b [flag] reboot device rkflashtool l <file load DDR init (MASK ROM MODE) rkflashtool L <file load USB loader (MASK ROM MODE) rkflashtool v read chip version rkflashtool n read NAND flash info rkflashtool i offset nsectors >outfile read IDBlocks rkflashtool j offset nsectors <infile write IDBlocks rkflashtool m offset nbytes >outfile read SDRAM rkflashtool M offset nbytes <infile write SDRAM rkflashtool B krnl_addr parm_addr exec SDRAM rkflashtool r partname >outfile read flash partition rkflashtool w partname <infile write flash partition rkflashtool r offset nsectors >outfile read flash rkflashtool w offset nsectors <infile write flash rkflashtool p >file fetch parameters rkflashtool P <file write parameters rkflashtool e partname erase flash (fill with 0xff) rkflashtool e offset nsectors erase flash (fill with 0xff)
  • ROCKPro64 - eMMC-Modul / SD-Karte auswählen

    Hardware hardware rockpro64
    3
    2
    0 Stimmen
    3 Beiträge
    2k Aufrufe
    FrankMF
    Echtes Problem gefunden. Wenn die eMMC-Karte verbaut ist, ich mit der SD-Karte starte (Jumper gesetzt), kann ich keinen Kernel updaten. Es ist alles ganz normal installiert, er startet aber immer den letzten vorhandenen. Jumper entfernt, eMMC-Modul entfernt! Bootvorgang mit unveränderter SD-Karte, neuer Kernel wird geladen. OK, das verstehe ich im Moment überhaupt nicht !?!?!?
  • Infrarot Empfänger

    Hardware hardware rockpro64
    1
    0 Stimmen
    1 Beiträge
    838 Aufrufe
    Niemand hat geantwortet
  • [HOWTO] SMD Widerstand Preproduction Board

    Verschoben Hardware howto hardware rockpro64
    2
    2
    0 Stimmen
    2 Beiträge
    865 Aufrufe
    FrankMF
    Offizielle Bestätigung -> http://files.pine64.org
  • ROCKPro64 - PCIe SATA Karte

    Verschoben Hardware hardware rockpro64
    13
    1
    0 Stimmen
    13 Beiträge
    4k Aufrufe
    FrankMF
    @elRadix : With pine64 sata-card you can use two hdd's. https://www.pine64.org/?product=rockpro64-pci-e-to-dual-sata-ii-interface-card For working cards please look into this thread before you buy anything.
  • [HOWTO] ROCKPro64 - Boot

    Verschoben Hardware howto hardware rockpro64
    5
    2
    0 Stimmen
    5 Beiträge
    4k Aufrufe
    FrankMF
    Das Problem sollte mit Kernel 4.19.0-rc4-1069-ayufan behoben sein.
  • Serielle Konsole UART2

    Angeheftet Verschoben Hardware hardware rockpro64
    8
    2
    0 Stimmen
    8 Beiträge
    3k Aufrufe
    FrankMF
    Ich verweise mal auf einen Artikel auf einer Webseite von mir, der Einsteiger Niveau hat. https://frank-mankel.de/wichtig/serielle-konsole Wenn es dann noch Probleme gibt, einfach fragen. Und beachte bitte, das wir hier nicht über PIs schreiben, sondern über ROCKPros. Da könnte es kleine Unterschiede geben. https://www.raspberrypi.org/documentation/configuration/uart.md