Skip to content

Nur mal so nebenbei: Ich finde schon länger die vielen YT-Distro-Videos ermüdend.

Uncategorized
2 2 0
  • Debian Bookworm 12.9 released

    Verschoben Linux debian linux bookworm
    1
    0 Stimmen
    1 Beiträge
    349 Aufrufe
    Niemand hat geantwortet
  • NodeBB - v3.6.0

    NodeBB nodebb linux
    1
    0 Stimmen
    1 Beiträge
    139 Aufrufe
    Niemand hat geantwortet
  • NodeBB - Update auf v1.18.6

    NodeBB nodebb nodejs linux
    1
    1
    0 Stimmen
    1 Beiträge
    177 Aufrufe
    Niemand hat geantwortet
  • Ubiquiti ER-X - iperf

    Verschoben OpenWRT & Ubiquiti ER-X openwrt linux er-x
    2
    1
    0 Stimmen
    2 Beiträge
    365 Aufrufe
    FrankMF
    Hier noch ein Test von DMZ / LAN und andersrum. frank@frank-MS-7C37:~$ iperf3 -c 192.168.5.15 Connecting to host 192.168.5.15, port 5201 [ 5] local 192.168.3.213 port 44052 connected to 192.168.5.15 port 5201 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 114 MBytes 952 Mbits/sec 314 153 KBytes [ 5] 1.00-2.00 sec 112 MBytes 937 Mbits/sec 259 205 KBytes [ 5] 2.00-3.00 sec 111 MBytes 929 Mbits/sec 210 212 KBytes [ 5] 3.00-4.00 sec 111 MBytes 934 Mbits/sec 235 202 KBytes [ 5] 4.00-5.00 sec 112 MBytes 936 Mbits/sec 263 153 KBytes [ 5] 5.00-6.00 sec 111 MBytes 935 Mbits/sec 255 209 KBytes [ 5] 6.00-7.00 sec 112 MBytes 937 Mbits/sec 313 129 KBytes [ 5] 7.00-8.00 sec 111 MBytes 932 Mbits/sec 296 209 KBytes [ 5] 8.00-9.00 sec 111 MBytes 934 Mbits/sec 258 208 KBytes [ 5] 9.00-10.00 sec 111 MBytes 934 Mbits/sec 292 201 KBytes - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-10.00 sec 1.09 GBytes 936 Mbits/sec 2695 sender [ 5] 0.00-10.00 sec 1.09 GBytes 935 Mbits/sec receiver iperf Done. frank@frank-MS-7C37:~$ iperf3 -R -c 192.168.5.15 Connecting to host 192.168.5.15, port 5201 Reverse mode, remote host 192.168.5.15 is sending [ 5] local 192.168.3.213 port 44058 connected to 192.168.5.15 port 5201 [ ID] Interval Transfer Bitrate [ 5] 0.00-1.00 sec 109 MBytes 911 Mbits/sec [ 5] 1.00-2.00 sec 109 MBytes 912 Mbits/sec [ 5] 2.00-3.00 sec 109 MBytes 912 Mbits/sec [ 5] 3.00-4.00 sec 109 MBytes 912 Mbits/sec [ 5] 4.00-5.00 sec 109 MBytes 912 Mbits/sec [ 5] 5.00-6.00 sec 108 MBytes 903 Mbits/sec [ 5] 6.00-7.00 sec 109 MBytes 912 Mbits/sec [ 5] 7.00-8.00 sec 109 MBytes 912 Mbits/sec [ 5] 8.00-9.00 sec 109 MBytes 912 Mbits/sec [ 5] 9.00-10.00 sec 109 MBytes 912 Mbits/sec - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-10.00 sec 1.06 GBytes 913 Mbits/sec 114 sender [ 5] 0.00-10.00 sec 1.06 GBytes 911 Mbits/sec receiver iperf Done.
  • Nach Kernel Update werden die Module nicht automatisch gebaut!?

    Linux linux
    1
    0 Stimmen
    1 Beiträge
    216 Aufrufe
    Niemand hat geantwortet
  • FAN control OMV Auyfan 0.10.12: gitlab-ci-linux-build-184, Kernel 5.6

    Linux linux
    12
    1 Stimmen
    12 Beiträge
    1k Aufrufe
    M
    Hi, since I'm currently change my rockpro64 setup I came across this. With the kernel from ayufan you need to set PWM_CTL to /sys/devices/platform/pwm-fan/hwmon/hwmon3/pwm1 for my self compiled one I need /sys/devices/platform/pwm-fan/hwmon/hwmon0/pwm1 But I got it only working with one entry for PWM_CTL e.g. PWM_CTL = "/sys/devices/platform/pwm-fan/hwmon/hwmon0/pwm1", after that you need to start ats again sudo systemctl stop ats sudo systemctl start ats initially the fan should start immediately for a short period of time. In case it is even a different one on your kernel you can find the right one using this command. sudo find /sys -name pwm1 | grep hwmon So far I'm not sure which kernel parameter or modul changes this. Martin
  • IPTables Logging

    Linux linux iptables
    1
    0 Stimmen
    1 Beiträge
    327 Aufrufe
    Niemand hat geantwortet
  • NodeBB - Upgrade auf v1.9.0

    NodeBB nodebb linux
    2
    1
    0 Stimmen
    2 Beiträge
    940 Aufrufe
    FrankMF
    Da oben fehlt ein Schritt. cd nodebb (or path to where nodebb is installed) ./nodebb stop git fetch git checkout v1.12.x git merge origin/v1.12.x ./nodebb upgrade Beim nächsten Upgrade testen.