Skip to content

Mainline Kernel 4.20.x

Verschoben Images
  • 4.19.0-rc4-1069-ayufan released

    • ayufan: rockpro64: fix emmc boot: Revert "mmc: sdhci-of-arasan: Add CQHCI…
  • 4.19.0-rc4-1071-ayufan released

    • rockchip: pcie: limit bus number to 31 inclusive
  • 4.19.0-1073-ayufan released

    Liste der Änderungen nicht gefunden. Es sind ein paar Dinge wohl geändert worden. Kann man hier nachlesen.

  • 4.20.0-rc6-1075-ayufan released

    Jede Menge Änderungen im dts File, die aber von Kamil noch nicht angepasst sind. Mein Testimage hier läuft mit PCIe NVMe SSD nicht. Also, noch abwarten!!

    (19:26:49) FrankM: ayufan5: 4.20 without pcie ? nvm card don't recognized. with 4.4 no problem.
    (19:31:02) ayufan5: FrankM: I did not yet fix dts 🙂

  • 4.20.0-1077-ayufan released

    Änderungen sind mir zur Zeit noch nicht bekannt. Test steht noch aus.

    PCIe NVMe Karte geht wieder.

    Kernel

    rock64@rockpro64:/mnt$ uname -a
    Linux rockpro64 4.20.0-1077-ayufan-gdeb16128b458 #ayufan SMP PREEMPT Sun Dec 30 12:00:17 UTC 2018 aarch64 aarch64 aarch64 GNU/Linux
    

    iozone

    rock64@rockpro64:/mnt$ sudo iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 
    	Iozone: Performance Test of File I/O
    	        Version $Revision: 3.429 $
    		Compiled for 64 bit mode.
    		Build: linux 
    
    	Contributors:William Norcott, Don Capps, Isom Crawford, Kirby Collins
    	             Al Slater, Scott Rhine, Mike Wisner, Ken Goss
    	             Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR,
    	             Randy Dunlap, Mark Montague, Dan Million, Gavin Brebner,
    	             Jean-Marc Zucconi, Jeff Blomberg, Benny Halevy, Dave Boone,
    	             Erik Habbinga, Kris Strecker, Walter Wong, Joshua Root,
    	             Fabrice Bacchella, Zhenghua Xue, Qin Li, Darren Sawyer,
    	             Vangel Bojaxhi, Ben England, Vikentsi Lapa.
    
    	Run began: Sun Dec 30 13:50:15 2018
    
    	Include fsync in write timing
    	O_DIRECT feature enabled
    	Auto Mode
    	File size set to 102400 kB
    	Record Size 4 kB
    	Record Size 16 kB
    	Record Size 512 kB
    	Record Size 1024 kB
    	Record Size 16384 kB
    	Command line used: iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2
    	Output is in kBytes/sec
    	Time Resolution = 0.000001 seconds.
    	Processor cache size set to 1024 kBytes.
    	Processor cache line size set to 32 bytes.
    	File stride size set to 17 * record size.
                                                                  random    random     bkwd    record    stride                                    
                  kB  reclen    write  rewrite    read    reread    read     write     read   rewrite      read   fwrite frewrite    fread  freread
              102400       4   105475   150901   165040   168152    55921   146649                                                          
              102400      16   323077   419261   446377   452714   199703   418553                                                          
              102400     512  1035241  1048622   962876   983026   776039  1044747                                                          
              102400    1024  1066733  1024204   922389   946779   863405  1042164                                                          
              102400   16384   942288  1384367  1395018  1457672  1446158  1372405                                                          
    
    iozone test complete.
    
  • 4.20.0-1081-ayufan & 4.20.0-1083-ayufan released

    1081 & 1083

    mmc: core: Add MMC Command Queue Support kernel parameter

    This parameter offers a workaround for cards that report command queue
    (CMDQ) support but don't work correctly when CMDQ is enabled. At least
    some ROCKPro64 + Foresee (32GB) eMMC card combinations have trouble
    working correctly. Setting mmc_cmdqueue=off in kernel command line
    disables CMDQ support and may help with troublesome hardware.

  • 4.20.0-1088-ayufan released ✌

    ayufan: defconfig: add rockchip_linux_defconfig

  • Läuft damit auch der delock Sata Controller?
    Ich befürchte du testest auf einem separatem RP64, oder?

  • Läuft damit auch der delock Sata Controller?
    Ich befürchte du testest auf einem separatem RP64, oder?

    @flockeee Aktuell teste ich auf einem anderen. Ich kann aber mal die SD-Karten tauschen 😉

  • @FrankM Vielen Dank, brauchst Du nicht. Habe es gerade getestet und es funktioniert alles.

  • @FrankM Vielen Dank, brauchst Du nicht. Habe es gerade getestet und es funktioniert alles.

    @flockeee Ok, dann kann ich ja updaten 😉

    Kleine Ergänzung. Heute nach dem Einschalten.

    Welcome to Ubuntu 18.04.1 LTS (GNU/Linux 4.20.0-1088-ayufan-gaac9b4fce0ab aarch64)
    

    Alles aktualisiert

    Welcome to Ubuntu 18.04.2 LTS (GNU/Linux 4.20.0-1088-ayufan-gaac9b4fce0ab aarch64)
    
  • WLan auf der Konsole einrichten

    Angeheftet Linux linux quartz64 rockpro64
    3
    0 Stimmen
    3 Beiträge
    684 Aufrufe
    FrankMF
    Ich kann im Manjaro keine WPA3 Sicherheit auswählen, dann bekomme ich keine Verbindung. Es geht nur WPA2 Personal. Gegenstelle ist eine FRITZ!Box 6591 Cable. [image: 1638114013848-2021-11-28_16-37.png] In der Fritzbox sieht das so aus [image: 1638114096062-50d23aa8-5f67-485e-a994-244ef4f6a270-image.png] Das kam als Fehlermeldung Nov 28 11:03:07 frank-pc wpa_supplicant[700]: wlan0: Trying to associate with SSID 'FRITZ!Box 6591 Cable AK' Nov 28 11:03:07 frank-pc wpa_supplicant[700]: wlan0: WPA: Failed to select authenticated key management type Nov 28 11:03:07 frank-pc wpa_supplicant[700]: wlan0: WPA: Failed to set WPA key management and encryption suites Ich denke, der Treiber unterstützt das nicht.
  • ROCKPro64 - Netflix?

    ROCKPro64 rockpro64
    2
    0 Stimmen
    2 Beiträge
    450 Aufrufe
    FrankMF
    Anleitung von Kamil # Netflix Starting with 0.8.0rc13 it is possible to use Netflix on all **Ubuntu/armf** desktop images using regular Chromium browser. Due to Google policies images do not ship Widevine CDM required by Netflix to decrypt videos. Currently, Widevine CDM is only available for **armhf** and **Ubuntu**. You have to install Widevine CDM with: ```bash install_widevine_drm.sh ``` This will take between 5 to 15 mins depending on the performance of SD-card, and your Internet connection.
  • ROCKPro64 - Das erste Mal

    Angeheftet Verschoben Hardware rockpro64
    5
    2
    1 Stimmen
    5 Beiträge
    954 Aufrufe
    FrankMF
    Ich kann heute die Fragen aller Fragen beantworten Damit ist leider die Frage immer noch unbeantwortet ob WLan und PCIe zusammen nutzbar ist!! Es geht!! Ich habe von MrFixit ein Testimage der RecalBox, benutzt das selbe Debian wie oben. Die Tage konnte man im IRC verfolgen, wie man dem Grundproblem näher kam und wohl einen Fix gebastelt hat, damit beides zusammen funktioniert. Mr.Fixit hat das in RecalBox eingebaut und ich durfte testen. # ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue qlen 1 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP8000> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 62:03:b0:d6:dc:b3 brd ff:ff:ff:ff:ff:ff 3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP8000> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether ac:83:f3:e6:1f:b2 brd ff:ff:ff:ff:ff:ff inet 192.168.178.27/24 brd 192.168.178.255 scope global wlan0 valid_lft forever preferred_lft forever inet6 2a02:908:1262:4680:ae83:f3ff:fee6:1fb2/64 scope global dynamic valid_lft 7145sec preferred_lft 3545sec inet6 fe80::ae83:f3ff:fee6:1fb2/64 scope link valid_lft forever preferred_lft forever # ls /mnt bin etc media recalbox sd.img test2.img boot home mnt root selinux tmp crypthome lib opt run srv usr dev lost+found proc sbin sys var # fdisk BusyBox v1.27.2 (2019-02-01 22:43:19 EST) multi-call binary. Usage: fdisk [-ul] [-C CYLINDERS] [-H HEADS] [-S SECTORS] [-b SSZ] DISK Change partition table -u Start and End are in sectors (instead of cylinders) -l Show partition table for each DISK, then exit -b 2048 (for certain MO disks) use 2048-byte sectors -C CYLINDERS Set number of cylinders/heads/sectors -H HEADS Typically 255 -S SECTORS Typically 63 # fdisk -l Disk /dev/mmcblk0: 15 GB, 15931539456 bytes, 31116288 sectors 486192 cylinders, 4 heads, 16 sectors/track Units: cylinders of 64 * 512 = 32768 bytes Device Boot StartCHS EndCHS StartLBA EndLBA Sectors Size Id Type /dev/mmcblk0p1 * 2,10,9 10,50,40 32768 163839 131072 64.0M c Win95 FAT32 (LBA) Partition 1 does not end on cylinder boundary /dev/mmcblk0p2 * 16,81,2 277,102,17 262144 4456447 4194304 2048M 83 Linux Partition 2 does not end on cylinder boundary /dev/mmcblk0p3 277,102,18 1023,254,63 4456448 31115263 26658816 12.7G 83 Linux Partition 3 does not end on cylinder boundary Disk /dev/nvme0n1: 233 GB, 250059350016 bytes, 488397168 sectors 2543735 cylinders, 12 heads, 16 sectors/track Units: cylinders of 192 * 512 = 98304 bytes Device Boot StartCHS EndCHS StartLBA EndLBA Sectors Size Id Type /dev/nvme0n1p1 1,0,1 907,11,16 2048 488397167 488395120 232G 83 Linux # Oben sieht man eine funktionierende WLan-Verbindung, das LAN-Kabel war entfernt. Unten sieht man die PCIe NVMe SSD, gemountet nach /mnt und Inhaltsausgabe. Das sollte beweisen, das der Ansatz der Lösung funktioniert. Leider kann ich nicht sagen, das es zum jetzigen Zeitpunkt stabil läuft. Ich habe einfach so Reboots, kann den Fehler aktuell aber nicht fangen. Mal sehen ob ich noch was finde. Aber, es ist ein Anfang!
  • Der 3. ROCKPro64

    ROCKPro64 rockpro64
    3
    0 Stimmen
    3 Beiträge
    1k Aufrufe
    FrankMF
    Nachdem ich jetzt mein NAS neu gemacht habe, schauen wir mal, was die Chinesen geliefert haben. Bestellt hatte ich ROCKPro64 v2.1 2GB RAM Kühlkörper Netzteil 3A USB-Adapter für eMMC-Modul Endlich habe ich mal an den USB-Adapter für das eMMC-Modul gedacht [image: 1540029625079-img_20181020_115348_ergebnis-resized.jpg] Was ist mir aufgefallen? Das Versionsdatum ist neu (siehe oben) Die PCIe NVMe Karte ist neu Bei der PCIe NVMe Karte liegt eine Abstandshülse aus Messing und eine winzig kleine Schraube bei. Damit bekomme ich aber nicht die NVMe-SSD befestigt. Ich habe dann gemurkst Da sollte Pine64 unbedingt nachbessern! So sieht das dann zusammengebaut aus. [image: 1540029757102-img_20181020_115425_ergebnis-resized.jpg] [image: 1540029767472-img_20181020_115438_ergebnis.jpg] Da ich ein paarmal gelesen hatte, das Leute Probleme mit dem PCIe NVMe Adapter hatten, direkt als erstes mal ein Test ob das reibungslos funktioniert. Sys rock64@rockpro64:/mnt$ uname -a Linux rockpro64 4.4.132-1075-rockchip-ayufan-ga83beded8524 #1 SMP Thu Jul 26 08:22:22 UTC 2018 aarch64 aarch64 aarch64 GNU/Linux lspci rock64@rockpro64:/mnt$ sudo lspci -vvv [sudo] password for rock64: 00:00.0 PCI bridge: Rockchip Inc. RK3399 PCI Express Root Port Device 0100 (prog-if 00 [Normal decode]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort+ <MAbort+ >SERR+ <PERR+ INTx- Latency: 0 Interrupt: pin A routed to IRQ 238 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00000000-00000fff Memory behind bridge: fa000000-fa0fffff Prefetchable memory behind bridge: 00000000-000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [80] Power Management version 3 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME+ Capabilities: [90] MSI: Enable+ Count=1/1 Maskable+ 64bit+ Address: 00000000fee30040 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [b0] MSI-X: Enable- Count=1 Masked- Vector table: BAR=0 offset=00000000 PBA: BAR=0 offset=00000008 Capabilities: [c0] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0 ExtTag- RBE+ DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L1, Exit Latency L0s <256ns, L1 <8us ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+ LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt+ AutBWInt+ LnkSta: Speed 5GT/s, Width x4, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #0, PowerLimit 0.000W; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Off, PwrInd Off, Power+ Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL+ CmdCplt- PresDet- Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR+, OBFF Via message ARIFwd+ DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [100 v2] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Capabilities: [274 v1] Transaction Processing Hints Interrupt vector mode supported Device specific mode supported Steering table in TPH capability structure Kernel driver in use: pcieport 01:00.0 Non-Volatile memory controller: Samsung Electronics Co Ltd NVMe SSD Controller SM961/PM961 (prog-if 02 [NVM Express]) Subsystem: Samsung Electronics Co Ltd NVMe SSD Controller SM961/PM961 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 237 Region 0: Memory at fa000000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/32 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [70] Express (v2) Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ SlotPowerLimit 0.000W DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 8GT/s, Width x4, ASPM L1, Exit Latency L0s unlimited, L1 <64us ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+ LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk- ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- LnkSta: Speed 5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR+, OBFF Not Supported DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [b0] MSI-X: Enable+ Count=8 Masked- Vector table: BAR=0 offset=00003000 PBA: BAR=0 offset=00002000 Capabilities: [100 v2] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Capabilities: [148 v1] Device Serial Number 00-00-00-00-00-00-00-00 Capabilities: [158 v1] Power Budgeting <?> Capabilities: [168 v1] #19 Capabilities: [188 v1] Latency Tolerance Reporting Max snoop latency: 0ns Max no snoop latency: 0ns Capabilities: [190 v1] L1 PM Substates L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+ PortCommonModeRestoreTime=10us PortTPowerOnTime=10us L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1- T_CommonMode=0us LTR1.2_Threshold=0ns L1SubCtl2: T_PwrOn=10us Kernel driver in use: nvme Da sieht alles gut aus. x4 alles Bestens! iozone rock64@rockpro64:/mnt$ sudo iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Iozone: Performance Test of File I/O Version $Revision: 3.429 $ Compiled for 64 bit mode. Build: linux Contributors:William Norcott, Don Capps, Isom Crawford, Kirby Collins Al Slater, Scott Rhine, Mike Wisner, Ken Goss Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR, Randy Dunlap, Mark Montague, Dan Million, Gavin Brebner, Jean-Marc Zucconi, Jeff Blomberg, Benny Halevy, Dave Boone, Erik Habbinga, Kris Strecker, Walter Wong, Joshua Root, Fabrice Bacchella, Zhenghua Xue, Qin Li, Darren Sawyer, Vangel Bojaxhi, Ben England, Vikentsi Lapa. Run began: Sat Oct 20 10:08:28 2018 Include fsync in write timing O_DIRECT feature enabled Auto Mode File size set to 102400 kB Record Size 4 kB Record Size 16 kB Record Size 512 kB Record Size 1024 kB Record Size 16384 kB Command line used: iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Output is in kBytes/sec Time Resolution = 0.000001 seconds. Processor cache size set to 1024 kBytes. Processor cache line size set to 32 bytes. File stride size set to 17 * record size. random random bkwd record stride kB reclen write rewrite read reread read write read rewrite read fwrite frewrite fread freread 102400 4 63896 108269 91858 95309 32845 73173 102400 16 123393 236653 273766 275807 118450 199130 102400 512 471775 570571 484612 496942 441345 575817 102400 1024 544229 642558 508895 511834 486506 647765 102400 16384 1044520 1100322 1069825 1092146 1089301 1086757 iozone test complete. Das sieht nicht optimal aus, schau ich mir später an. Das hier soll nur ein kurzer Test sein ob das Board rennt Nachdem ich mittlerweile zwei ROCKPro64 im "produktiven" Einsatz habe, war es immer sehr mühsam mal eben was zu testen. Man will die anderen ja nicht immer ausmachen, dran rumhantieren usw. Deswegen jetzt der dritte, der im Moment dann die Rolle des Testkandidaten einnimmt. Ab sofort kann ich wieder nach Lust und Laune, neue Images testen usw.
  • USB 3.0 - SATA Adapter

    Hardware hardware rockpro64
    2
    3
    0 Stimmen
    2 Beiträge
    811 Aufrufe
    FrankMF
    Heute das Ganze mal mit einer Samsung 860 Pro mit 256GB. Eingesetztes Filesystem ext4 rock64@rockpro64v2_1:/mnt$ uname -a Linux rockpro64v2_1 4.4.132-1077-rockchip-ayufan-gbaf35a9343cb #1 SMP Mon Jul 30 14:06:57 UTC 2018 aarch64 aarch64 aarch64 GNU/Linux Speedtest rock64@rockpro64v2_1:/mnt$ sudo iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Iozone: Performance Test of File I/O Version $Revision: 3.429 $ Compiled for 64 bit mode. Build: linux Contributors:William Norcott, Don Capps, Isom Crawford, Kirby Collins Al Slater, Scott Rhine, Mike Wisner, Ken Goss Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR, Randy Dunlap, Mark Montague, Dan Million, Gavin Brebner, Jean-Marc Zucconi, Jeff Blomberg, Benny Halevy, Dave Boone, Erik Habbinga, Kris Strecker, Walter Wong, Joshua Root, Fabrice Bacchella, Zhenghua Xue, Qin Li, Darren Sawyer, Vangel Bojaxhi, Ben England, Vikentsi Lapa. Run began: Tue Jul 31 14:27:17 2018 Include fsync in write timing O_DIRECT feature enabled Auto Mode File size set to 102400 kB Record Size 4 kB Record Size 16 kB Record Size 512 kB Record Size 1024 kB Record Size 16384 kB Command line used: iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Output is in kBytes/sec Time Resolution = 0.000001 seconds. Processor cache size set to 1024 kBytes. Processor cache line size set to 32 bytes. File stride size set to 17 * record size. random random bkwd record stride kB reclen write rewrite read reread read write read rewrite read fwrite frewrite fread freread 102400 4 17896 23350 30390 31362 21611 14611 102400 16 56756 59180 86296 93819 51778 57327 102400 512 201347 221961 220840 222338 210887 230781 102400 1024 253752 273695 263884 266256 250153 273528 102400 16384 351112 356007 366417 372264 368721 356177 iozone test complete. DD Schreiben rock64@rockpro64v2_1:/mnt$ sudo dd if=/dev/zero of=sd.img bs=1M count=4096 conv=fdatasync 4096+0 records in 4096+0 records out 4294967296 bytes (4.3 GB, 4.0 GiB) copied, 12.8358 s, 335 MB/s Lesen rock64@rockpro64v2_1:/mnt$ sudo dd if=sd.img of=/dev/null bs=1M count=4096 4096+0 records in 4096+0 records out 4294967296 bytes (4.3 GB, 4.0 GiB) copied, 11.4787 s, 374 MB/s Fazit Damit scheint der Adapter ganz gut am USB3.0 zu funktionieren. Die Schreibgeschwindigkeit ist ca. dreimal höher als mit der anderen SSD.
  • OMV Images

    ROCKPro64 rockpro64
    3
    0 Stimmen
    3 Beiträge
    971 Aufrufe
    FrankMF
    Kurzes Update https://github.com/ayufan-rock64/linux-build/releases/download/0.8.0rc10/stretch-openmediavault-rockpro64-0.8.0rc10-1125-armhf.img.xz Startet Incl. WiFi & PCIe NVMe SSD War aber nur ein ganz kurzer Test!!
  • ROCKPro64 - PCIe SATA Karte

    Verschoben Hardware hardware rockpro64
    13
    1
    0 Stimmen
    13 Beiträge
    4k Aufrufe
    FrankMF
    @elRadix : With pine64 sata-card you can use two hdd's. https://www.pine64.org/?product=rockpro64-pci-e-to-dual-sata-ii-interface-card For working cards please look into this thread before you buy anything.
  • Armbianmonitor

    ROCKPro64 rockpro64
    1
    1
    0 Stimmen
    1 Beiträge
    1k Aufrufe
    Niemand hat geantwortet