Skip to content

ROCKPro64 - PCIe SATA Karte

Verschoben Hardware
  • 0_1530285585857_IMG_20180517_091459_ergebnis.jpg

    Pine64 liefert diese SATA-Karte aus. Amazon-Link

    Technische Spezifikationen mal da geklaut

    • Zwei SATA-Ports und zwei eSATA-Ports - Vier unabhängige Ports werden für Ihren PCI-Computer hinzugefügt sodass gibt es die Vorteile der optionalen Festplatte. Eine superschnelle und leistungsstarke Datentransferlösung. Stabiler und zuverlässiger Chipsatz ASMEDIA ASM1061.
    • Kompatibel mit Serial ATA Revision 3.0 Spezifikation. Kompatibel mit Single-Lane (x1) PCI Express Spezifikation Revision 1.0.
    • Datenübertragungsrate bis zu 750 MB / s (6,0 Gbps). Unterstützt 2,5 Gbps PCI-E-Bus mit Vollduplex-Kanal. Unterstützt zwei unabhängige SATA 3.0-Kanäle (Unterstützt 2 SATA-Geräte gleichzeitig.) Verwenden Sie Jumpers, um zwischen SATA zu wählen oder eSATA-Schnittstelle.
    • Unterstützt ATAPI-Geräte: CD-ROM, DVD-ROM usw. Keine externe Stromversorgung für die Karte erforderlich. Unterstützt Hot-Swapping und Boot-Funktion.
    • Kommt mit einer Treiber-CD, kompatibel mit dem Betriebssystem Windows XP / Vista / 7/8/10. Enthält eine Halterung mit voller Höhe und einer halben Höhe für ein kleines Gehäuse.

    Ich kann nichts für den Text 🙂

    Mein eingesetztes Linux

    rock64@rockpro64:~$ uname -a
    Linux rockpro64 4.4.126-rockchip-ayufan-257 #1 SMP Sun Jun 10 18:30:43 UTC 2018 aarch64 aarch64 aarch64 GNU/Linux
    

    Ein lspci zeigt den Adapter an.

    rock64@rockpro64:~$ lspci
    00:00.0 PCI bridge: Rockchip Inc. RK3399 PCI Express Root Port Device 0100
    01:00.0 SATA controller: ASMedia Technology Inc. ASM1062 Serial ATA Controller (rev 02)
    

    Das Ganze was ausführlicher mit sudo lspci -vvv

    rock64@rockpro64:~$ sudo lspci -vvv
    [sudo] password for rock64: 
    00:00.0 PCI bridge: Rockchip Inc. RK3399 PCI Express Root Port Device 0100 (prog-if 00 [Normal decode])
    	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort+ <MAbort+ >SERR+ <PERR+ INTx-
    	Latency: 0
    	Interrupt: pin A routed to IRQ 238
    	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    	I/O behind bridge: 00000000-00000fff
    	Memory behind bridge: fa000000-fa0fffff
    	Prefetchable memory behind bridge: 00000000-000fffff
    	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
    	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
    		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    	Capabilities: [80] Power Management version 3
    		Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
    		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME+
    	Capabilities: [90] MSI: Enable+ Count=1/1 Maskable+ 64bit+
    		Address: 00000000fee30040  Data: 0000
    		Masking: 00000000  Pending: 00000000
    	Capabilities: [b0] MSI-X: Enable- Count=1 Masked-
    		Vector table: BAR=0 offset=00000000
    		PBA: BAR=0 offset=00000008
    	Capabilities: [c0] Express (v2) Root Port (Slot+), MSI 00
    		DevCap:	MaxPayload 256 bytes, PhantFunc 0
    			ExtTag- RBE+
    		DevCtl:	Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
    			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
    			MaxPayload 128 bytes, MaxReadReq 512 bytes
    		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
    		LnkCap:	Port #0, Speed 5GT/s, Width x4, ASPM L1, Exit Latency L0s <256ns, L1 <8us
    			ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+
    		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk-
    			ExtSynch- ClockPM- AutWidDis- BWInt+ AutBWInt+
    		LnkSta:	Speed 5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
    		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
    			Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
    		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
    			Control: AttnInd Off, PwrInd Off, Power+ Interlock-
    		SltSta:	Status: AttnBtn- PowerFlt- MRL+ CmdCplt- PresDet- Interlock-
    			Changed: MRL- PresDet- LinkState-
    		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
    		RootCap: CRSVisible-
    		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
    		DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR+, OBFF Via message ARIFwd+
    		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
    		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
    			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
    			 Compliance De-emphasis: -6dB
    		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
    			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
    	Capabilities: [100 v2] Advanced Error Reporting
    		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
    		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
    		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
    		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
    		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
    		AERCap:	First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
    	Capabilities: [274 v1] Transaction Processing Hints
    		Interrupt vector mode supported
    		Device specific mode supported
    		Steering table in TPH capability structure
    	Kernel driver in use: pcieport
    
    01:00.0 SATA controller: ASMedia Technology Inc. ASM1062 Serial ATA Controller (rev 02) (prog-if 01 [AHCI 1.0])
    	Subsystem: ASMedia Technology Inc. ASM1062 Serial ATA Controller
    	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    	Interrupt: pin A routed to IRQ 237
    	Region 0: I/O ports at <unassigned> [disabled]
    	Region 1: I/O ports at <unassigned> [disabled]
    	Region 2: I/O ports at <unassigned> [disabled]
    	Region 3: I/O ports at <unassigned> [disabled]
    	Region 4: I/O ports at <unassigned> [disabled]
    	Region 5: Memory at fa010000 (32-bit, non-prefetchable) [disabled] [size=512]
    	[virtual] Expansion ROM at fa000000 [disabled] [size=64K]
    	Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit-
    		Address: 00000000  Data: 0000
    	Capabilities: [78] Power Management version 3
    		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    	Capabilities: [80] Express (v2) Legacy Endpoint, MSI 00
    		DevCap:	MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us
    			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
    		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
    			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
    			MaxPayload 128 bytes, MaxReadReq 512 bytes
    		DevSta:	CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
    		LnkCap:	Port #1, Speed 5GT/s, Width x1, ASPM not supported, Exit Latency L0s unlimited, L1 <2us
    			ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
    		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk-
    			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
    		LnkSta:	Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
    		DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR-, OBFF Not Supported
    		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
    		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
    			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
    			 Compliance De-emphasis: -6dB
    		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
    			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
    	Capabilities: [100 v1] Virtual Channel
    		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
    		Arb:	Fixed- WRR32- WRR64- WRR128-
    		Ctrl:	ArbSelect=Fixed
    		Status:	InProgress-
    		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
    			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
    			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
    			Status:	NegoPending- InProgress-
    

    Das hier

    LnkSta:	Speed 5GT/s, Width x1,
    

    würde der Spezifikation (sieh oben) entsprechen.

    Ausgabe dmesg | grep -E "pcie"

    rock64@rockpro64:~$ sudo dmesg | grep -E "pcie"
    [    0.501600] of_get_named_gpiod_flags: parsed 'gpio' property of node '/vcc3v3-pcie-regulator[0]' - status (0)
    [    0.501653] reg-fixed-voltage vcc3v3-pcie-regulator: Looking up vin-supply from device tree
    [    0.501694] vcc3v3_pcie: supplied by dc_12v
    [    0.501762] vcc3v3_pcie: 3300 mV 
    [    0.501918] reg-fixed-voltage vcc3v3-pcie-regulator: vcc3v3_pcie supplying 3300000uV
    [    2.856112] vcc3v3_pcie: disabling
    [    3.254877] phy phy-pcie-phy.9: Looking up phy-supply from device tree
    [    3.254887] phy phy-pcie-phy.9: Looking up phy-supply property in node /pcie-phy failed
    [    3.256549] rockchip-pcie f8000000.pcie: GPIO lookup for consumer ep
    [    3.256573] rockchip-pcie f8000000.pcie: using device tree for GPIO lookup
    [    3.256651] of_get_named_gpiod_flags: parsed 'ep-gpios' property of node '/pcie@f8000000[0]' - status (0)
    [    3.257162] rockchip-pcie f8000000.pcie: Looking up vpcie3v3-supply from device tree
    [    3.257437] rockchip-pcie f8000000.pcie: Looking up vpcie1v8-supply from device tree
    [    3.257459] rockchip-pcie f8000000.pcie: Looking up vpcie1v8-supply property in node /pcie@f8000000 failed
    [    3.257511] rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found
    [    3.495350] rockchip-pcie f8000000.pcie: Looking up vpcie0v9-supply from device tree
    [    3.495390] rockchip-pcie f8000000.pcie: Looking up vpcie0v9-supply property in node /pcie@f8000000 failed
    [    3.495444] rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found
    [    3.503758] rockchip-pcie f8000000.pcie: invalid power supply
    [    3.552104] PCI host bridge /pcie@f8000000 ranges:
    [    3.567421] rockchip-pcie f8000000.pcie: PCI host bridge to bus 0000:00
    [    3.714885] pcieport 0000:00:00.0: enabling device (0000 -> 0002)
    [    3.719417] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt
    [    3.728397] pcie_pme 0000:00:00.0:pcie01: service driver pcie_pme loaded
    [    3.729619] aer 0000:00:00.0:pcie02: service driver aer loaded
    [    6.872320] Modules linked in: ip_tables x_tables autofs4 phy_rockchip_pcie midgard_kbase
    

    Das Ding ist ja hotplug fähig, also schließe ich jetzt mal eine SSD an den e-SATA Anschluss an. Und hier wird es blöd, weil egal was ich mache es wird keine SSD/HDD erkannt. 😞

    Update1:

    Mir kam die Idee, die SSD mal extern mit Strom zu versorgen. Ausprobiert und festgestellt, geht immer noch nichts. Außer das die LED auf der SATA-Karte (blau) kurz aufblitzt. Abgestürzt. Ok, auch keine Lösung. Ich hab da aber noch was im Kopf....

    Update2:

    Ein neue PCIe SATA Karte ist hier. Eingebaut und x-mal gestartet - funktioniert nicht. System stürzt beim Booten ab.

    https://pastebin.com/h2XmJeGy
    wird fortgesetzt...

  • Mal ein Update in der Geschichte PCIe SATA-Karte

    Sie funktioniert!

    0_1530717883830_IMG_20180704_170602_ergebnis.jpg

    System

     rock64@rockpro64:/mnt$ uname -a
     Linux rockpro64 4.18.0-rc3-1037-ayufan-gb95494bd8d0f #1 SMP PREEMPT Tue Jul 3 20:00:21 UTC 2018 aarch64 aarch64 aarch64 GNU/Linux
    

    Musste ein wenig tricksen um eine SSD ans Laufen zu bekommen 🙂

    0_1530717938249_IMG_20180704_170811_ergebnis.jpg

    lspci

    rock64@rockpro64:/mnt$ sudo lspci -vvv
    00:00.0 PCI bridge: Rockchip Inc. RK3399 PCI Express Root Port Device 0100 (prog-if 00 [Normal decode])
    	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    	Latency: 0
    	Interrupt: pin A routed to IRQ 255
    	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    	I/O behind bridge: 00000000-00000fff
    	Memory behind bridge: fa000000-fa0fffff
    	Prefetchable memory behind bridge: 00000000-000fffff
    	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
    	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
    		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    	Capabilities: [80] Power Management version 3
    		Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
    		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
    	Capabilities: [90] MSI: Enable- Count=1/1 Maskable+ 64bit+
    		Address: 0000000000000000  Data: 0000
    		Masking: 00000000  Pending: 00000000
    	Capabilities: [b0] MSI-X: Enable- Count=1 Masked-
    		Vector table: BAR=0 offset=00000000
    		PBA: BAR=0 offset=00000008
    	Capabilities: [c0] Express (v2) Root Port (Slot+), MSI 00
    		DevCap:	MaxPayload 256 bytes, PhantFunc 0
    			ExtTag- RBE+
    		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
    			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
    			MaxPayload 256 bytes, MaxReadReq 512 bytes
    		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
    		LnkCap:	Port #0, Speed 5GT/s, Width x4, ASPM L1, Exit Latency L0s <256ns, L1 <8us
    			ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+
    		LnkCtl:	ASPM Disabled; RCB 128 bytes Disabled- CommClk-
    			ExtSynch- ClockPM- AutWidDis- BWInt+ AutBWInt+
    		LnkSta:	Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
    		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
    			Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
    		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
    			Control: AttnInd Off, PwrInd Off, Power+ Interlock-
    		SltSta:	Status: AttnBtn- PowerFlt- MRL+ CmdCplt- PresDet- Interlock-
    			Changed: MRL- PresDet- LinkState-
    		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
    		RootCap: CRSVisible-
    		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
    		DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR+, OBFF Via message ARIFwd+
    		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
    		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
    			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
    			 Compliance De-emphasis: -6dB
    		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
    			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
    	Capabilities: [100 v2] Advanced Error Reporting
    		UESta:	DLP- SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
    		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
    		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
    		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
    		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
    		AERCap:	First Error Pointer: 0d, GenCap+ CGenEn- ChkCap+ ChkEn-
    	Capabilities: [274 v1] Transaction Processing Hints
    		Interrupt vector mode supported
    		Device specific mode supported
    		Steering table in TPH capability structure
    
    01:00.0 SATA controller: ASMedia Technology Inc. ASM1062 Serial ATA Controller (rev 02) (prog-if 01 [AHCI 1.0])
    	Subsystem: ASMedia Technology Inc. ASM1062 Serial ATA Controller
    	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    	Latency: 0
    	Interrupt: pin A routed to IRQ 231
    	Region 0: I/O ports at <unassigned> [disabled]
    	Region 1: I/O ports at <unassigned> [disabled]
    	Region 2: I/O ports at <unassigned> [disabled]
    	Region 3: I/O ports at <unassigned> [disabled]
    	Region 4: I/O ports at <unassigned> [disabled]
    	Region 5: Memory at fa010000 (32-bit, non-prefetchable) [size=512]
    	[virtual] Expansion ROM at fa000000 [disabled] [size=64K]
    	Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
    		Address: fee30040  Data: 0000
    	Capabilities: [78] Power Management version 3
    		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    	Capabilities: [80] Express (v2) Legacy Endpoint, MSI 00
    		DevCap:	MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us
    			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
    		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
    			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
    			MaxPayload 256 bytes, MaxReadReq 512 bytes
    		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
    		LnkCap:	Port #1, Speed 5GT/s, Width x1, ASPM not supported, Exit Latency L0s unlimited, L1 <2us
    			ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
    		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk-
    			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
    		LnkSta:	Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
    		DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR-, OBFF Not Supported
    		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
    		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
    			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
    			 Compliance De-emphasis: -6dB
    		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
    			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
    	Capabilities: [100 v1] Virtual Channel
    		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
    		Arb:	Fixed- WRR32- WRR64- WRR128-
    		Ctrl:	ArbSelect=Fixed
    		Status:	InProgress-
    		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
    			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
    			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
    			Status:	NegoPending- InProgress-
    	Kernel driver in use: ahci
    

    Laut Kamil ist das dann auf 380MB/s begrenzt.

    iozone

    rock64@rockpro64:/mnt$ sudo iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 
    	Iozone: Performance Test of File I/O
    	        Version $Revision: 3.429 $
    		Compiled for 64 bit mode.
    		Build: linux 
    
    	Contributors:William Norcott, Don Capps, Isom Crawford, Kirby Collins
    	             Al Slater, Scott Rhine, Mike Wisner, Ken Goss
    	             Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR,
    	             Randy Dunlap, Mark Montague, Dan Million, Gavin Brebner,
    	             Jean-Marc Zucconi, Jeff Blomberg, Benny Halevy, Dave Boone,
    	             Erik Habbinga, Kris Strecker, Walter Wong, Joshua Root,
    	             Fabrice Bacchella, Zhenghua Xue, Qin Li, Darren Sawyer,
    	             Vangel Bojaxhi, Ben England, Vikentsi Lapa.
    
    	Run began: Wed Jul  4 15:05:37 2018
    
    	Include fsync in write timing
    	O_DIRECT feature enabled
    	Auto Mode
    	File size set to 102400 kB
    	Record Size 4 kB
    	Record Size 16 kB
    	Record Size 512 kB
    	Record Size 1024 kB
    	Record Size 16384 kB
    	Command line used: iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2
    	Output is in kBytes/sec
    	Time Resolution = 0.000001 seconds.
    	Processor cache size set to 1024 kBytes.
    	Processor cache line size set to 32 bytes.
    	File stride size set to 17 * record size.
                                                                  random    random     bkwd    record    stride                                    
                  kB  reclen    write  rewrite    read    reread    read     write     read   rewrite      read   fwrite frewrite    fread  freread
              102400       4    40073    65587    76408    76546    23702    13602                                                          
              102400      16   113539   157707   181745   182323    47126    51496                                                          
              102400     512   328802   326047   277146   278351   270958   336556                                                          
              102400    1024   331734   358670   313116   314032   313441   334537                                                          
              102400   16384   189982   225176   234192   346836   381690   370403                                                          
    
    iozone test complete.
    

    Ich such dann mal eine zweite Platte.......

  • Mit 0.7.8 noch mal die PCIe SATA Karte testen.

    Hardware

    • SSD Festplatte 220GB
    • HDD Festplatte irgendwas mit um die 110GB -uralt-

    Software

    rock64@rockpro64:/media$ uname -a
    Linux rockpro64 4.4.132-1072-rockchip-ayufan-ga1d27dba5a2e #1 SMP Sat Jul 21 20:18:03 UTC 2018 aarch64 aarch64 aarch64 GNU/Linux
    

    0_1532255867307_SATA.jpg

    Adpater

    rock64@rockpro64:/media$ sudo lspci -vvv
    00:00.0 PCI bridge: Rockchip Inc. RK3399 PCI Express Root Port Device 0100 (prog-if 00 [Normal decode])
    	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort+ <MAbort+ >SERR+ <PERR+ INTx-
    	Latency: 0
    	Interrupt: pin A routed to IRQ 238
    	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    	I/O behind bridge: 00000000-00000fff
    	Memory behind bridge: fa000000-fa0fffff
    	Prefetchable memory behind bridge: 00000000-000fffff
    	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
    	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
    		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    	Capabilities: [80] Power Management version 3
    		Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
    		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME+
    	Capabilities: [90] MSI: Enable+ Count=1/1 Maskable+ 64bit+
    		Address: 00000000fee30040  Data: 0000
    		Masking: 00000000  Pending: 00000000
    	Capabilities: [b0] MSI-X: Enable- Count=1 Masked-
    		Vector table: BAR=0 offset=00000000
    		PBA: BAR=0 offset=00000008
    	Capabilities: [c0] Express (v2) Root Port (Slot+), MSI 00
    		DevCap:	MaxPayload 256 bytes, PhantFunc 0
    			ExtTag- RBE+
    		DevCtl:	Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
    			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
    			MaxPayload 128 bytes, MaxReadReq 512 bytes
    		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
    		LnkCap:	Port #0, Speed 5GT/s, Width x4, ASPM L1, Exit Latency L0s <256ns, L1 <8us
    			ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+
    		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk-
    			ExtSynch- ClockPM- AutWidDis- BWInt+ AutBWInt+
    		LnkSta:	Speed 5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
    		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
    			Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
    		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
    			Control: AttnInd Off, PwrInd Off, Power+ Interlock-
    		SltSta:	Status: AttnBtn- PowerFlt- MRL+ CmdCplt- PresDet- Interlock-
    			Changed: MRL- PresDet- LinkState-
    		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
    		RootCap: CRSVisible-
    		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
    		DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR+, OBFF Via message ARIFwd+
    		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
    		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
    			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
    			 Compliance De-emphasis: -6dB
    		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
    			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
    	Capabilities: [100 v2] Advanced Error Reporting
    		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
    		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
    		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
    		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
    		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
    		AERCap:	First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
    	Capabilities: [274 v1] Transaction Processing Hints
    		Interrupt vector mode supported
    		Device specific mode supported
    		Steering table in TPH capability structure
    	Kernel driver in use: pcieport
    
    01:00.0 SATA controller: ASMedia Technology Inc. ASM1062 Serial ATA Controller (rev 02) (prog-if 01 [AHCI 1.0])
    	Subsystem: ASMedia Technology Inc. ASM1062 Serial ATA Controller
    	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    	Latency: 0
    	Interrupt: pin A routed to IRQ 239
    	Region 0: I/O ports at <unassigned> [disabled]
    	Region 1: I/O ports at <unassigned> [disabled]
    	Region 2: I/O ports at <unassigned> [disabled]
    	Region 3: I/O ports at <unassigned> [disabled]
    	Region 4: I/O ports at <unassigned> [disabled]
    	Region 5: Memory at fa010000 (32-bit, non-prefetchable) [size=512]
    	[virtual] Expansion ROM at fa000000 [disabled] [size=64K]
    	Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
    		Address: fee30040  Data: 0000
    	Capabilities: [78] Power Management version 3
    		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    	Capabilities: [80] Express (v2) Legacy Endpoint, MSI 00
    		DevCap:	MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us
    			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
    		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
    			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
    			MaxPayload 128 bytes, MaxReadReq 512 bytes
    		DevSta:	CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
    		LnkCap:	Port #1, Speed 5GT/s, Width x1, ASPM not supported, Exit Latency L0s unlimited, L1 <2us
    			ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
    		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk-
    			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
    		LnkSta:	Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
    		DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR-, OBFF Not Supported
    		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
    		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
    			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
    			 Compliance De-emphasis: -6dB
    		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
    			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
    	Capabilities: [100 v1] Virtual Channel
    		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
    		Arb:	Fixed- WRR32- WRR64- WRR128-
    		Ctrl:	ArbSelect=Fixed
    		Status:	InProgress-
    		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
    			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
    			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
    			Status:	NegoPending- InProgress-
    	Kernel driver in use: ahci
    

    Einmal der PCIe Adapter und die SATA Karte. So weit alles gut.

    Speedtest

    SSD

    rock64@rockpro64:/mnt$ sudo dd if=/dev/zero of=sd77.img bs=1M count=4096 conv=fdatasync
    4096+0 records in
    4096+0 records out
    4294967296 bytes (4.3 GB, 4.0 GiB) copied, 38.4839 s, 112 MB/s
    

    iozone

    rock64@rockpro64:/mnt$ sudo iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 
    	Iozone: Performance Test of File I/O
    	        Version $Revision: 3.429 $
    		Compiled for 64 bit mode.
    		Build: linux 
    
    	Contributors:William Norcott, Don Capps, Isom Crawford, Kirby Collins
    	             Al Slater, Scott Rhine, Mike Wisner, Ken Goss
    	             Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR,
    	             Randy Dunlap, Mark Montague, Dan Million, Gavin Brebner,
    	             Jean-Marc Zucconi, Jeff Blomberg, Benny Halevy, Dave Boone,
    	             Erik Habbinga, Kris Strecker, Walter Wong, Joshua Root,
    	             Fabrice Bacchella, Zhenghua Xue, Qin Li, Darren Sawyer,
    	             Vangel Bojaxhi, Ben England, Vikentsi Lapa.
    
    	Run began: Sun Jul 22 10:42:12 2018
    
    	Include fsync in write timing
    	O_DIRECT feature enabled
    	Auto Mode
    	File size set to 102400 kB
    	Record Size 4 kB
    	Record Size 16 kB
    	Record Size 512 kB
    	Record Size 1024 kB
    	Record Size 16384 kB
    	Command line used: iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2
    	Output is in kBytes/sec
    	Time Resolution = 0.000001 seconds.
    	Processor cache size set to 1024 kBytes.
    	Processor cache line size set to 32 bytes.
    	File stride size set to 17 * record size.
                                                                  random    random     bkwd    record    stride                                    
                  kB  reclen    write  rewrite    read    reread    read     write     read   rewrite      read   fwrite frewrite    fread  freread
              102400       4    28792    39366    52678    58495    13219    12889                                                          
              102400      16    61995    61928    88041   104969    38578    35227                                                          
              102400     512   159905    71439   214899   217569   214569   260194                                                          
              102400    1024   128472    85136   245539   246448   242433   178743                                                          
              102400   16384   329869   354069   323670   324324   324528   339370                                                          
    
    iozone test complete.
    

    HDD

    rock64@rockpro64:/media$ sudo dd if=/dev/zero of=sd.img bs=1M count=4096 conv=fdatasync
    4096+0 records in
    4096+0 records out
    4294967296 bytes (4.3 GB, 4.0 GiB) copied, 76.8208 s, 55.9 MB/s
    

    iozone

    rock64@rockpro64:/media$ sudo iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 
    	Iozone: Performance Test of File I/O
    	        Version $Revision: 3.429 $
    		Compiled for 64 bit mode.
    		Build: linux 
    
    	Contributors:William Norcott, Don Capps, Isom Crawford, Kirby Collins
    	             Al Slater, Scott Rhine, Mike Wisner, Ken Goss
    	             Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR,
    	             Randy Dunlap, Mark Montague, Dan Million, Gavin Brebner,
    	             Jean-Marc Zucconi, Jeff Blomberg, Benny Halevy, Dave Boone,
    	             Erik Habbinga, Kris Strecker, Walter Wong, Joshua Root,
    	             Fabrice Bacchella, Zhenghua Xue, Qin Li, Darren Sawyer,
    	             Vangel Bojaxhi, Ben England, Vikentsi Lapa.
    
    	Run began: Sun Jul 22 10:33:22 2018
    
    	Include fsync in write timing
    	O_DIRECT feature enabled
    	Auto Mode
    	File size set to 102400 kB
    	Record Size 4 kB
    	Record Size 16 kB
    	Record Size 512 kB
    	Record Size 1024 kB
    	Record Size 16384 kB
    	Command line used: iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2
    	Output is in kBytes/sec
    	Time Resolution = 0.000001 seconds.
    	Processor cache size set to 1024 kBytes.
    	Processor cache line size set to 32 bytes.
    	File stride size set to 17 * record size.
                                                                  random    random     bkwd    record    stride                                    
                  kB  reclen    write  rewrite    read    reread    read     write     read   rewrite      read   fwrite frewrite    fread  freread
              102400       4    11683    21724    16840    16994      607     1219                                                          
              102400      16    29607    43380    44428    44267     2412     5658                                                          
              102400     512    54547    55261    50275    58474    31425    38247                                                          
              102400    1024    53838    52901    51727    54370    41678    45017                                                          
              102400   16384    54735    53438    51128    53344    50381    55148                                                          
    
    iozone test complete.
    

    Der HDD Test ist nicht aussagekräftig, das ist eine uralte 3,5 Zoll HDD!! Die dient hier nur zum Testen ob das auch mit zwei Platten funktioniert!!!

    Kopieren

    Ich kann mich daran erinnern, das ichbeim letzten Test Probleme hatte ein File von der einen auf die andere Festplatte zu kopieren. Da ist beim letzten Mal das ganze System gecrasht.

    Das ging dieses mal einwandfrei!

    LED

    Auf der SATA Karte ist eine blaue LED, diese leuchtet bei Zugriff auf die angeschlossenen Festplatten.

    0_1532256524293_IMG_20180722_124611.jpg

    Fazit

    Viel Spaß beim NAS bauen 🙂

    Eine andere Karte eines anderen Herstellers funktioniert nicht und löst eine Kernel Panic aus.

  • Hi,

    wie gibst du den angeschlossenen Platten an der PCIe Sata Karte Strom?
    Extra Netzteil oder über das Board?

    Grüße Alex

  • @schwabe93

    Hallo, ich benutze das folgende Kabel. https://www.pine64.org/?product=rockpro64-power-cable-for-dual-sata-drives

    Das kann man sich zur Not auch selber basteln. Ich habe am Anfang auch mal mit einem handelsüblichen PC-Netzteil experimentiert, obwohl ich da immer ein ungutes Gefühl hatte.

  • Hmm, ok ich habe mir gestern bei Amazon das hier bestellt https://www.amazon.de/dp/B072JLHGQT
    funktioniert leider nicht, bzw, vllt bin auch falsch dran wo ich den 4 Pin Stecker reinstecken muss auf dem Board. Laut meinem Verständnis Direkt hinter dem DC IN Anschluss? Dort wo GND steht.

    Danke für deine Hilfe

  • Das war keine so gute Idee. Schau mal ...

    0_1533330087484_IMG_20180803_225536_ergebnis.jpg

    Auf dem Board ist der weiße Steckplatz (Con15) neben DC IN. Dieser stellt zweimal 12VDC zur Verfügung.

    Pin 1&2 = 12VDC
    Pin3&4 = GND

    siehe Seite 11 -> http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf

    0_1533330093810_IMG_20180803_225546_ergebnis.jpg

    Wenn ich jetzt keinen Denkfehler habe, ist immer noch zu heiß zum Denken, dann ist aber nichts kaputt gegangen. Es funktioniert nur nicht. Glück gehabt 😉

    Mit dem jetzt vorhandenen Adapter könntest du dir aber mit den Informationen, den richtigen Adapter eben zusammen basteln. Ich habe aber keine Ahnung ob das für dich ein Problem ist. Ich als Elektriker sehe das nicht als großes Problem an.

    Wenn du dir unsicher bist, dann lass es lieber!! Bevor noch das schöne Board abbrennt 🙂

  • @frankm

    Dann werde ich mir wohl die offizielen kabel bestellen, weil rumbasteln werde ich da nicht an irgendeiner Elektronik.
    Der Rock läuft ja gottseidank noch, solange bis das teil da ist werde ich halt mit USB arbeiten.

  • @schwabe93 Lass es mich wissen, wenn du das Kabel hast, wie es so bei dir funktioniert.

  • @frankm So habe das Kabel erhalten, gleichmal angesteckt und mit 2 3.5 Zoll Festplatten getestet läuft wunderbar, jetzt kann ich anfangen mein NAS zu bauen.

  • Freut mich, das es jetzt klappt. Viel Spaß beim Bauen eines NAS.

    Ich bin auch immer an netten Bildern interessiert, was andere so mit ihren ROCKPros machen 😉

  • @FrankM

    Re: ROCKPro64 - PCIe SATA Karte

    how may HDD can you attach to the RockPro with this addon card? is 4 HDD possible?

  • @elRadix : With pine64 sata-card you can use two hdd's. https://www.pine64.org/?product=rockpro64-pci-e-to-dual-sata-ii-interface-card

    For working cards please look into this thread before you buy anything.

  • 0 Stimmen
    13 Beiträge
    795 Aufrufe
    N

    @frankm Alles Klar!
    Wie schon erwähnt, für meine Zwecke rechts! Die Jahre über hat gute Dienste geleistet (PCI-e und HDD) und wird hoffentlich auch noch ein paar Jahre bis zum nächsten Umbau tun!
    Vielen Dank!

  • SATA Adapter - SSD kopieren

    Hardware
    1
    0 Stimmen
    1 Beiträge
    179 Aufrufe
    Niemand hat geantwortet
  • SATA Karte Marvell 88SE9230 Chipsatz mit 0.9.16

    Hardware
    8
    0 Stimmen
    8 Beiträge
    599 Aufrufe
    FrankMF

    Gestern hat Kamil einen neuen Kernel released, so das ich das heute mal auf dem NAS probiert habe. Durch den Boot von der USB-SSD sollten die Pfade ja alle passen und man problemlos den Kernel updaten können.

    root@rockpro64:/usr/local/sbin# df -h Dateisystem Größe Benutzt Verf. Verw% Eingehängt auf udev 992M 0 992M 0% /dev tmpfs 199M 5,5M 194M 3% /run /dev/sdc7 459G 3,3G 437G 1% / tmpfs 995M 0 995M 0% /dev/shm tmpfs 5,0M 4,0K 5,0M 1% /run/lock tmpfs 995M 0 995M 0% /sys/fs/cgroup /dev/sdc6 112M 4,0K 112M 1% /boot/efi /dev/md0 3,6T 485G 3,0T 14% /mnt/nas tmpfs 199M 0 199M 0% /run/user/1000

    Gut, /boot liegt auf der USB-SSD. Also, wie bekannt, den Kernel heruntergeladen und installiert. Nach dem Neustart geht nix 😞 Mittels HDMI Monitor angeschlossen um den Fehler sehen zu können, da macht es auch schon Klick. Der Parameter

    pci=nomsi

    ist durch das Kernel-Update überschrieben worden. Ich hatte dann die USB-SSD ausgebaut und das Problem am lokalen Rechner gelöst. Aber, man ist ja faul.....;)

    Da es überschrieben wird, müssen auch irgendwo die Informationen dazu liegen.......

    /usr/local/sbin/update-extlinux.sh

    Da ist das File, was Kamil dafür angelegt hat.

    #!/bin/bash TIMEOUT="" DEFAULT="" APPEND="rw" APPEND="$APPEND panic=10" APPEND="$APPEND init=/sbin/init" APPEND="$APPEND coherent_pool=1M" APPEND="$APPEND ethaddr=\${ethaddr} eth1addr=\${eth1addr} serial=\${serial#}" APPEND="$APPEND cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1 pci=nomsi" [..........gekürzt.........]

    Hier seht ihr das File schon mit meiner Änderung, in der Hoffnung das es dann beim nächsten Mal ohne Probleme funktioniert. Bleibt nur noch das Problem, wann ändert Kamil das File, weil dann ist die Änderung wieder weg!?!?

  • ROCKPro64 - Armbian - NAS umgezogen

    Armbian
    2
    0 Stimmen
    2 Beiträge
    566 Aufrufe
    FrankMF

    Das NAS mit den drei 2,5 Zoll HDD Platten läuft an einem 3A Netzteil - ohne Probleme. Hat heute Nacht die Jobs einwandfrei erledigt 😉

    Link Preview Image PINE64 Community

    PINE64 is a large, vibrant and diverse community and creates software, documentation and projects.

    favicon

    (www.pine64.org)

  • Unterstützung Lüfter

    ROCKPro64
    5
    0 Stimmen
    5 Beiträge
    2k Aufrufe
    FrankMF

    Mit dem neuen Release hatte jemand das mal ausprobiert -> https://forum.frank-mankel.org/topic/795/fan-control-omv-auyfan-0-10-12-gitlab-ci-linux-build-184-kernel-5-6/6

    Dieser Kernel kam zur Anwendung

    Linux rockpro64 5.6.0-1137-ayufan-ge57f05e7bf8f #ayufan SMP Wed Apr 15 10:16:02 UTC 2020 aarch64 GNU/Linux

    Dort stellt man dann fest, das sich eine Kleinigkeit geändert hat. Der Pfad und der Dateiname hat sich geändert.

    Kontrollieren kann man das mit

    nano /sys/devices/platform/pwm-fan/hwmon/hwmon3/pwm1

    Der Wert geht von 0 - 255, wie gehabt.

  • 0 Stimmen
    3 Beiträge
    2k Aufrufe
    FrankMF

    Echtes Problem gefunden.

    Wenn die eMMC-Karte verbaut ist, ich mit der SD-Karte starte (Jumper gesetzt), kann ich keinen Kernel updaten. Es ist alles ganz normal installiert, er startet aber immer den letzten vorhandenen.

    Jumper entfernt, eMMC-Modul entfernt!

    Bootvorgang mit unveränderter SD-Karte, neuer Kernel wird geladen.

    OK, das verstehe ich im Moment überhaupt nicht !?!?!?

  • 0 Stimmen
    2 Beiträge
    2k Aufrufe
    FrankMF
    Ergänzung

    Eine andere SATA-Karte und eine Riser-Karte mit angeschlossener GPU startet nicht.

    rock64@rockpro64v2_1:~$ uname -a Linux rockpro64v2_1 4.4.132-1075-rockchip-ayufan-ga83beded8524 #1 SMP Thu Jul 26 08:22:22 UTC 2018 aarch64 aarch64 aarch64 GNU/Linux
  • u-boot-erase-spi-rockpro64.img.xz

    Verschoben Tools
    1
    0 Stimmen
    1 Beiträge
    877 Aufrufe
    Niemand hat geantwortet