Skip to content

Vorserienmodell

ROCKPro64
  • Dran denken, wir haben hier ein sehr frühes Modell auf dem Tisch. Hier ein paar Info's, die ich nicht vergessen möchte, deswegen schreibe ich das hier auf. 🙂

    Probleme

    • (16:02:35) tllim: 1. Lacking POWER LED. This is miscommunication between engineers and layout engineer drop this LED. This will put back on netx batch
    • (16:03:54) tllim: 2. There is a small yellow tape near LCD DSI connector. This prevent the LCD flat ribbon cable touch the surronding resistor and caught short circuit. This will improve on nex batch.
    • (16:04:24) tllim: 3. There is no RECOVERY button staff. Not sure whetehr we will staff on next batch
    • (16:08:32) tllim: the othe rtwo LED also a bit bright, we will dim down on next batch

    Boot

    Zur Zeit unklar, testen!!

    • (16:22:52) lukasz: tllim: but wont the SD boot Android image just work from eMMC with dd ?
    • (16:24:30) tllim: @lukasz, for Allwinner yes, for ROCKChip no

    Recovery-Button nötig?

    • (16:47:26) frankm: From forum "When used properly, it puts the board into Loader Mode, which is a special mode in the bootloader which allows data to be written/read directly from the eMMC chip, over a USB cable to a computer." I think i don't need this. Will see...
    • (16:50:48) tllim: the ROCKPro64 and ROCK64 using same method

    .... wird ständig erweitert

    Quelle: IRC-Chat

  • RockPro64 - Mainline Kernel 5.9.x vom Kamil

    Images
    5
    0 Stimmen
    5 Beiträge
    402 Aufrufe
    FrankMF

    Hoppla, nach langer Zeit mal was Neues vom Kamil.

    5.9.0-1146-ayufan released

    WIP: cdn_dp hdmi audio switch
  • ROCKPro64 - Anpassen resize_rootfs.sh

    Angeheftet ROCKPro64
    3
    0 Stimmen
    3 Beiträge
    421 Aufrufe
    FrankMF

    Seit Release 0.10.10 ist das automatische Vergrößern der Root Partition mit drin 🙂

    0.10.10: Support automated resize when booting from nvme

    Einfach das Image auf die NVMe SSD schreiben, ab in den ROCKPro64 und fertig! Nach dem Booten wird die Partition dann automatisch auf die maximal mögliche Größe erweitert.

    Kamil hat das Script auch ein wenig angepasst.

    case $dev in /dev/mmcblk?p?) DISK=${dev:0:12} PART=${dev:13} NAME="sd/emmc" ;; /dev/sd??) DISK=${dev:0:8} PART=${dev:8} NAME="hdd/ssd" ;; /dev/nvme?n?p?) DISK=${dev:0:12} PART=${dev:13} NAME="pcie/nvme" ;;

    Das Resultat bei einer Samsung 979 EVO mit 500GB Speicher

    rock64@rockpro64:~$ df -h Filesystem Size Used Avail Use% Mounted on udev 918M 0 918M 0% /dev tmpfs 192M 5.2M 187M 3% /run /dev/nvme0n1p4 459G 1.2G 439G 1% / tmpfs 957M 0 957M 0% /dev/shm tmpfs 5.0M 4.0K 5.0M 1% /run/lock tmpfs 957M 0 957M 0% /sys/fs/cgroup /dev/nvme0n1p3 229M 44M 169M 21% /boot /dev/nvme0n1p2 12M 0 12M 0% /boot/efi tmpfs 192M 0 192M 0% /run/user/1000

    Perfekt. Danke Kamil!

  • NVMe - Booten jetzt möglich

    Angeheftet ROCKPro64
    7
    0 Stimmen
    7 Beiträge
    681 Aufrufe
    FrankMF

    Hallo @mabs,

    ja. Der uboot wird in den SPI Speicher geladen. Der sucht dann beim Starten nach einem bootfähigem Device. So wie auf einem ganz normalen PC. Eine richtig coole Sache, wo ich mich freue, das das langsam mal funktioniert.

    Die Performance wird ja dann sicherlich von dem Device bestimmt. Dazu gibt es ja genug Messungen. Ich würde eine NVMe SSD immer einer SATA Platte vorziehen. Es kommt aber auf den Anwendungsfall an.

    Für ein NAS dann eher zwei oder mehr SATA Platten, und von USB3 HDD booten 🙂 So wie ich das schon lange betreibe.

    Aber, da hat auch jeder andere Vorstellungen und Vorlieben für.

  • ROCKPro64 - Armbian - NAS umgezogen

    Armbian
    2
    0 Stimmen
    2 Beiträge
    566 Aufrufe
    FrankMF

    Das NAS mit den drei 2,5 Zoll HDD Platten läuft an einem 3A Netzteil - ohne Probleme. Hat heute Nacht die Jobs einwandfrei erledigt 😉

    Link Preview Image PINE64 Community

    PINE64 is a large, vibrant and diverse community and creates software, documentation and projects.

    favicon

    (www.pine64.org)

  • 0 Stimmen
    2 Beiträge
    1k Aufrufe
    FrankMF

    This repo contains the tn40xx Linux driver for 10Gbit NICs based on the TN4010 MAC from Tehuti Networks.

    This driver enables the following 10Gb SFP+ NICs:

    D-Link DXE-810S
    Edimax EN-9320SFP+
    StarTech PEX10000SFP
    Synology E10G15-F1
    ... as well as the following 10GBase-T/NBASE-T NICs:

    D-Link DXE-810T
    Edimax EN-9320TX-E
    EXSYS EX-6061-2
    Intellinet 507950
    StarTech ST10GSPEXNB

    Quelle: https://github.com/ayufan-rock64/tn40xx-driver/tree/master

  • Infrarot Empfänger

    Hardware
    1
    0 Stimmen
    1 Beiträge
    779 Aufrufe
    Niemand hat geantwortet
  • 0 Stimmen
    1 Beiträge
    843 Aufrufe
    Niemand hat geantwortet
  • Benchmarks

    Angeheftet Verschoben Archiv
    10
    0 Stimmen
    10 Beiträge
    2k Aufrufe
    FrankMF
    iozone Test (0.6.52) Hardware

    Hardware ist eine Samsung EVO 960 m.2 mit 250GB

    Eingabe sudo iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Ausgabe Run began: Thu Jun 14 12:04:01 2018 Include fsync in write timing O_DIRECT feature enabled Auto Mode File size set to 102400 kB Record Size 4 kB Record Size 16 kB Record Size 512 kB Record Size 1024 kB Record Size 16384 kB Command line used: iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Output is in kBytes/sec Time Resolution = 0.000001 seconds. Processor cache size set to 1024 kBytes. Processor cache line size set to 32 bytes. File stride size set to 17 * record size. random random bkwd record stride kB reclen write rewrite read reread read write read rewrite read fwrite frewrite fread freread 102400 4 40859 79542 101334 101666 31721 60459 102400 16 113215 202566 234307 233091 108334 154750 102400 512 362864 412548 359279 362810 340235 412626 102400 1024 400478 453205 381115 385746 372378 453548 102400 16384 583762 598047 595752 596251 590950 604690

    Zum direkten Vergleich hier heute mal mit 4.17.0-rc6-1019

    rock64@rockpro64:/mnt$ uname -a Linux rockpro64 4.17.0-rc6-1019-ayufan-gfafc3e1c913f #1 SMP PREEMPT Tue Jun 12 19:06:59 UTC 2018 aarch64 aarch64 aarch64 GNU/Linux iozone Test rock64@rockpro64:/mnt$ sudo iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Iozone: Performance Test of File I/O Version $Revision: 3.429 $ Compiled for 64 bit mode. Build: linux Contributors:William Norcott, Don Capps, Isom Crawford, Kirby Collins Al Slater, Scott Rhine, Mike Wisner, Ken Goss Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR, Randy Dunlap, Mark Montague, Dan Million, Gavin Brebner, Jean-Marc Zucconi, Jeff Blomberg, Benny Halevy, Dave Boone, Erik Habbinga, Kris Strecker, Walter Wong, Joshua Root, Fabrice Bacchella, Zhenghua Xue, Qin Li, Darren Sawyer, Vangel Bojaxhi, Ben England, Vikentsi Lapa. Run began: Sat Jun 16 06:34:43 2018 Include fsync in write timing O_DIRECT feature enabled Auto Mode File size set to 102400 kB Record Size 4 kB Record Size 16 kB Record Size 512 kB Record Size 1024 kB Record Size 16384 kB Command line used: iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Output is in kBytes/sec Time Resolution = 0.000001 seconds. Processor cache size set to 1024 kBytes. Processor cache line size set to 32 bytes. File stride size set to 17 * record size. random random bkwd record stride kB reclen write rewrite read reread read write read rewrite read fwrite frewrite fread freread 102400 4 48672 104754 115838 116803 47894 103606 102400 16 168084 276437 292660 295458 162550 273703 102400 512 566572 597648 580005 589209 534508 597007 102400 1024 585621 624443 590545 599177 569452 630098 102400 16384 504871 754710 765558 780592 777696 753426 iozone test complete.