• Hallo!
    Nach vielen Jahren problemlosem Betrieb (auch nach Stromausfällen) hakt es nach dem letzten Stromausfall (verursacht durch einen eifrigen Monteur des Stromanbieters) massiv.

    Vielleicht kann mir jemand Schritt für Schritt helfen.

    Nach dem Reboot läuft zwar das System (nextcloudPi) rund (kann mich einloggen, etc.), aber der eingerichtete Software Raid ist verschwunden:

    cat /proc/mdstat
    Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] 
    unused devices: <none>
    

    Eigentlich sind zwei SATA disks im Raid1 eingebaut, und dort drauf liegen / lagen die Daten für Nexcloud.

    Ich habe nun keine Ahnung, wie ich das angehe. Ich hoffe inständig, dass auf den Platten noch alles da ist.. und da möchte ich schon gerne versuchen, ob ich das System wieder an den Start bekomme.

    Leider kann ich nicht auf dieser Ebene nicht gut "Terminal". Die Hilfe müsste daher sehr "noob", eben step by step, sein.

    LG
    Chris


  • @rockverynew sagte in RockPro64: Raid fehlt nach Absturz:

    ata6: COMRESET failed (errno=-16)

    Ich muss ganz ehrlich gestehen, das ich nicht weiß was da bei Dir falsch läuft. Da du von einem Stromausfall sprachst, würde ich vermuten, das eine der Platten evt. einen Filesystem Schaden hat.

    Wenn man nach dem Fehler von oben googelt, kommt das hier

    https://forums.unraid.net/topic/47934-solved-comreset-failed-errno-16-received/
    

    Darüber hinaus, sieht der Kernel auch ziemlich wüst aus. Was man machen könnte.

    • Ein anderes Image ausprobieren um auszuschließen, das es daran liegt.
    • Die HDDs in einem richtigen PC mal auf Funktion und Filesystem Errors testen.

    Das würde ich zu mindestens so machen.

    Was Du auch noch machen kannst, ist nur eine Platte anzuschließen um zu testen, ob es dann läuft. Dein Raid1 ist ja nur eine Spiegelung. Das mal wechselweise machen. Vielleicht hat nur eine Platte einen weg!?

    Dann meckert das Raid zwar, aber funktionieren sollte es.


  • Z.B. wäre es super, wenn ich mal checken könnte, ob der SATA HardwareController kaputt gegangen ist. Dann würde ich schauen, ob die HDDs einen Fehler haben.
    Erst dann macht es ja Sinn, zu versuchen das raid wieder herzustellen.

    Ich habe kleider keine Ahnung, wie man das am jetzt konkret angeht.


  • Nächste Schritt: Mit

    hwinfo
    

    kriege ich

    10: PCI 100.0: 0106 SATA controller (AHCI 1.0)
      [Created at pci.386]
      Unique ID: VCu0.TTpyRDzu1K2
      Parent ID: qLht.1JvK5jWGUsF
      SysFS ID: /devices/platform/f8000000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0
      SysFS BusID: 0000:01:00.0
      Hardware Class: storage
      Model: "Marvell 88SE9230 PCIe SATA 6Gb/s Controller"
      Vendor: pci 0x1b4b "Marvell Technology Group Ltd."
      Device: pci 0x9230 "88SE9230 PCIe SATA 6Gb/s Controller"
      SubVendor: pci 0x1b4b "Marvell Technology Group Ltd."
      SubDevice: pci 0x9230 
      Revision: 0x11
      Driver: "ahci"
      Driver Modules: "ahci"
      Memory Range: 0xfa040000-0xfa0407ff (rw,non-prefetchable)
      Memory Range: 0xfa000000-0xfa03ffff (ro,non-prefetchable)
      IRQ: 231 (no events)
      Module Alias: "pci:v00001B4Bd00009230sv00001B4Bsd00009230bc01sc06i01"
      Config Status: cfg=new, avail=yes, need=no, active=unknown
      Attached to: #9 (PCI bridge)
    

    Die Hardware wird also erkannt, richtig? Allerdings irritiert mich das "active=unknown".
    Als nächstes baue ich die HDDs aus und schließe sie mal lesend an einen anderen PC. Mal sehen, vielleicht gibt's so einen Durchbruch.


  • Das hab ich auch noch gesehen:

    ----- /proc/modules -----
      midgard_kbase 643072 0 - Live 0xffffff8000d98000
      rockchip_saradc 16384 0 - Live 0xffffff8000d8f000
      ip_tables 24576 0 - Live 0xffffff8000d84000
      x_tables 32768 1 ip_tables, Live 0xffffff8000d75000
      autofs4 40960 2 - Live 0xffffff8000d63000
      raid10 45056 0 - Live 0xffffff8000d52000
      raid456 98304 0 - Live 0xffffff8000d2f000
      async_raid6_recov 16384 1 raid456, Live 0xffffff8000d28000
      async_memcpy 16384 1 raid456, Live 0xffffff8000d21000
      async_pq 16384 1 raid456, Live 0xffffff8000d19000
      async_xor 16384 2 raid456,async_pq, Live 0xffffff8000d12000
      async_tx 16384 5 raid456,async_raid6_recov,async_memcpy,async_pq,async_xor, Live 0xffffff8000d0a000
      raid1 40960 0 - Live 0xffffff8000cfa000
      raid0 20480 0 - Live 0xffffff8000cf0000
      multipath 16384 0 - Live 0xffffff8000ce7000
      linear 16384 0 - Live 0xffffff8000cdf000
      md_mod 131072 6 raid10,raid456,raid1,raid0,multipath,linear, Live 0xffffff8000cb0000
    ----- /proc/modules end -----
    

    Das heißt doch, dass die Module im Kernel geladen wurden?
    Alles immer mit Fragezeichen, weil ich tatsächlich keine Ahnung habe, wie ich diese Zeilen interpretieren soll.

    Freu mich über jede Hilfe & jeden Hinweis.


  • Hallo und Willkommen 😎

    Was sagt denn

    fdisk -l
    

  • @FrankM

    Disk /dev/ram0: 4 MiB, 4194304 bytes, 8192 sectors
    Units: sectors of 1 * 512 = 512 bytes
    Sector size (logical/physical): 512 bytes / 4096 bytes
    I/O size (minimum/optimal): 4096 bytes / 4096 bytes
    
    
    Disk /dev/mtdblock0: 4 MiB, 4161536 bytes, 8128 sectors
    Units: sectors of 1 * 512 = 512 bytes
    Sector size (logical/physical): 512 bytes / 512 bytes
    I/O size (minimum/optimal): 512 bytes / 512 bytes
    
    
    Disk /dev/mtdblock1: 32 KiB, 32768 bytes, 64 sectors
    Units: sectors of 1 * 512 = 512 bytes
    Sector size (logical/physical): 512 bytes / 512 bytes
    I/O size (minimum/optimal): 512 bytes / 512 bytes
    
    
    Disk /dev/mtdblock2: 256 KiB, 262144 bytes, 512 sectors
    Units: sectors of 1 * 512 = 512 bytes
    Sector size (logical/physical): 512 bytes / 512 bytes
    I/O size (minimum/optimal): 512 bytes / 512 bytes
    
    
    Disk /dev/mmcblk0: 59.5 GiB, 63864569856 bytes, 124735488 sectors
    Units: sectors of 1 * 512 = 512 bytes
    Sector size (logical/physical): 512 bytes / 512 bytes
    I/O size (minimum/optimal): 512 bytes / 512 bytes
    Disklabel type: gpt
    Disk identifier: 0A5B9081-9F09-4B66-A3E6-87B85C9893B1
    
    Device          Start       End   Sectors  Size Type
    /dev/mmcblk0p1     64      8063      8000  3.9M Linux filesystem
    /dev/mmcblk0p2   8064      8191       128   64K Linux filesystem
    /dev/mmcblk0p3   8192     16383      8192    4M Linux filesystem
    /dev/mmcblk0p4  16384     24575      8192    4M Linux filesystem
    /dev/mmcblk0p5  24576     32767      8192    4M Linux filesystem
    /dev/mmcblk0p6  32768    262143    229376  112M Microsoft basic data
    /dev/mmcblk0p7 262144 124735454 124473311 59.4G Linux filesystem
    
    

    Keine Spur von den zwei HDDs


  • Ist schon ein paar Tage her, wo ich noch Raids auf einem RockPro64 gebaut habe.....

    /etc/mdadm/mdadm.conf
    

    Ist die Konfiguration noch vorhanden?


  • @FrankM
    Ich hab das System grade runtergefahren, weil ich die Platten testweise mal hier extern dranhängen will.
    Wir ein bisserl dauern, bis ich da nachsehen kann.
    Danke schon mal für deine Hilfe..


  • @rockverynew Ja, ja.. eine Platte lässt sich problemlos einhängen und meldet sich als Teil eines Raidverbundes an. Die zweite ist erscheint erst nach gehöriger Zeit, und verschickt die Warnung, dass sie bald den Geist aufgibt ("likely to fail soon")
    Ich bau das jetzt wieder rein, und hoffe, dass ich das retten kann, bevor die erste Platte das Zeitliche segnet.


  • @FrankM sagte in RockPro64: Raid fehlt nach Absturz:

    Ist schon ein paar Tage her, wo ich noch Raids auf einem RockPro64 gebaut habe.....

    /etc/mdadm/mdadm.conf
    

    Ist die Konfiguration noch vorhanden?

    yes:

    # mdadm.conf
    #
    # !NB! Run update-initramfs -u after updating this file.
    # !NB! This will ensure that initramfs has an uptodate copy.
    #
    # Please refer to mdadm.conf(5) for information about this file.
    #
    
    # by default (built-in), scan all partitions (/proc/partitions) and all
    # containers for MD superblocks. alternatively, specify devices to scan, using
    # wildcards if desired.
    #DEVICE partitions containers
    
    # automatically tag new arrays as belonging to the local system
    HOMEHOST <system>
    
    # instruct the monitoring daemon where to send mail alerts
    MAILADDR root
    
    # definitions of existing MD arrays
    
    # This configuration was auto-generated on Sun, 29 Mar 2020 19:46:34 +0000 by mkconf
    ARRAY /dev/md0 metadata=1.2 name=rockpro64:0 UUID=1eb53b0b:1f053805:259388d3:1bd4fb1a
    

  • Mir gehen aktuell die Ideen aus. Welches System wird von WO gestartet? SD-Karte?

    Ist vor dem Stromausfall ein neuer Kernel installiert worden, der jetzt nach dem Neustart rum zickt?

    Ich habe ansonsten keine Einfälle mehr, für mehr müsste man das System sehen.


  • @FrankM
    Das System startet von der SD Karte
    Auf dem RAID waren eigentlich nur die Daten von nextcloud.
    Ich habe vor dem Stromausfall keine Updates gemacht.
    Aber.. jetzt wo du das erwähnst .. fällt mir ein, dass ich nach dem Stromausfall und, nachdem ich festgestellt habe, dass nix geht, ein Update gemacht haben könnte. Das nextcloudPi System bringt ein paar Skripte mit, die das Updaten leicht möglich machen. Ich habe das aaber auch deswegen nicht ernst genommen, weil das Skript nicht zu laufen schien. War in Bruchteilen von Sekunden "fertig".


  • @FrankM sagte in RockPro64: Raid fehlt nach Absturz:

    Ich habe ansonsten keine Einfälle mehr, für mehr müsste man das System sehen.

    Was für Infos genau darf ich dir wie aus dem System rausziehen?


  • sudo blkid
    /dev/mmcblk0p6: SEC_TYPE="msdos" LABEL="boot" UUID="C633-139A" TYPE="vfat" PARTLABEL="boot" PARTUUID="19fac854-9b68-4b2d-8438-e29a7b08acc7"
    /dev/mmcblk0p7: LABEL="linux-root" UUID="608e0dfa-a3af-4451-bc88-eee2234d7fb4" TYPE="ext4" PARTLABEL="root" PARTUUID="aa061210-0de9-465b-a17a-b610b564d9af"
    /dev/mmcblk0: PTUUID="0a5b9081-9f09-4b66-a3e6-87b85c9893b1" PTTYPE="gpt"
    /dev/mmcblk0p1: PARTLABEL="loader1" PARTUUID="e450cf06-4a56-4fa8-a051-0b169ede53f9"
    /dev/mmcblk0p2: PARTLABEL="reserved1" PARTUUID="26d64f56-609a-4837-b9f0-b21d80825653"
    /dev/mmcblk0p3: PARTLABEL="reserved2" PARTUUID="e215f23c-6ae9-4b09-b9aa-cc428fc673a7"
    /dev/mmcblk0p4: PARTLABEL="loader2" PARTUUID="6577edc5-8ca2-43ba-a54d-852da20268b1"
    /dev/mmcblk0p5: PARTLABEL="atf" PARTUUID="222cf45d-87a0-473b-b5ca-e94005af85cb"
    

    Es ist sehr merkwürdig, dass es auf der SD Karte auch so viele Partitionen gibt. Könnte es sein, dass die Partitionstabellen beim Absturz kaputt gegangen sind?
    hab mal sowas gelesen


  • Sorry, dass ich hier so viel poste.. Ich habe die Hoffnung noch nicht aufgegeben 😉

    sudo cat /etc/fstab
    LABEL=boot /boot/efi vfat defaults,sync 0 0
    /dev/md0 /mnt/md0 ext4 defaults,nofail,discard 0 0
    # a swapfile is not a swap partition, no line here
    #   use  dphys-swapfile swap[on|off]  for that
    

    in der fstab ist der RAID noch drinnen.
    Nur sda und sdb werden gar nicht gefunden / angezeigt.
    Wie kann ich meinem System sagen, dass es die Festplatten neu suchen soll?
    Oder kann man davon ausgehen, dass der SATA controller kaputtgegangen ist?


  • Zur Beruhigung, die Daten auf den HDDs sollten noch da sein, da würde ich mir aktuell keine Sorgen machen. Was mich stutzig macht ist, das der Controller keine HDD erkennt!?

    lspci -vvv
    

    gibt was aus?

    Und mal bitte die Ausgabe von

    dmesg
    

  • @FrankM

    lspci -vvv                                                                                 
    00:00.0 PCI bridge: Fuzhou Rockchip Electronics Co., Ltd RK3399 PCI Express Root Port (prog-if 00 [Normal decode])
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin A routed to IRQ 231
    Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    I/O behind bridge: 00000000-00000fff
    Memory behind bridge: fa000000-fa0fffff
    Prefetchable memory behind bridge: 00000000-000fffff
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
    BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
    PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    Capabilities: <access denied>
    Kernel driver in use: pcieport
    
    01:00.0 SATA controller: Marvell Technology Group Ltd. 88SE9230 PCIe SATA 6Gb/s Controller (rev 11) (prog-if 01 [AHCI 1.0])
    Subsystem: Marvell Technology Group Ltd. 88SE9230 PCIe SATA 6Gb/s Controller
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin A routed to IRQ 231
    Region 0: I/O ports at 0000
    Region 1: I/O ports at 0000
    Region 2: I/O ports at 0000
    Region 3: I/O ports at 0000
    Region 4: I/O ports at 0000
    Region 5: Memory at fa040000 (32-bit, non-prefetchable) [size=2K]
    Expansion ROM at fa000000 [size=256K]
    Capabilities: <access denied>
    Kernel driver in use: ahci
    

    Die errors in dmesg brauchen ein neues Post, vielleicht kann ich das sogar nur auf mehrere Posts aufteilen..


  • dmesg
    [    0.000000] Booting Linux on physical CPU 0x0
    [    0.000000] Initializing cgroup subsys cpuset
    [    0.000000] Initializing cgroup subsys cpu
    [    0.000000] Initializing cgroup subsys cpuacct
    [    0.000000] Linux version 4.4.202-1237-rockchip-ayufan-gfd4492386213 (root@runner-f725ff63-project-5943294-concurrent-0) (gcc version 7.4.0 (Ubuntu/Linaro 7.4.0-1ubuntu1~18.04.1) ) #1 SMP Sat Nov 23 13:55:47 UTC 2019
    [    0.000000] Boot CPU: AArch64 Processor [410fd034]
    [    0.000000] earlycon: Early serial console at MMIO32 0xff1a0000 (options '')
    [    0.000000] bootconsole [uart0] enabled
    [    0.000000] Reserved memory: failed to reserve memory for node 'drm-logo@00000000': base 0x0000000000000000, size 0 MiB
    [    0.000000] On node 0 totalpages: 1015296
    [    0.000000]   DMA zone: 15864 pages used for memmap
    [    0.000000]   DMA zone: 0 pages reserved
    [    0.000000]   DMA zone: 1015296 pages, LIFO batch:31
    [    0.000000] psci: probing for conduit method from DT.
    [    0.000000] psci: PSCIv1.0 detected in firmware.
    [    0.000000] psci: Using standard PSCI v0.2 function IDs
    [    0.000000] psci: MIGRATE_INFO_TYPE not supported.
    [    0.000000] psci: SMC Calling Convention v1.0
    [    0.000000] PERCPU: Embedded 20 pages/cpu @ffffffc0f7eda000 s42152 r8192 d31576 u81920
    [    0.000000] pcpu-alloc: s42152 r8192 d31576 u81920 alloc=20*4096
    [    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 
    [    0.000000] Detected VIPT I-cache on CPU0
    [    0.000000] CPU features: enabling workaround for ARM erratum 845719
    [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 999432
    [    0.000000] Kernel command line: earlycon=uart8250,mmio32,0xff1a0000 swiotlb=1 no_console_suspend=1 usbcore.autosuspend=-1 rw panic=10 init=/sbin/init coherent_pool=1M ethaddr=7e:40:50:9c:3d:8a eth1addr= serial=9428f9b9d9bbb3c cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1 pci=nomsi root=LABEL=linux-root rootwait rootfstype=ext4
    [    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
    [    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
    [    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
    [    0.000000] software IO TLB: mapped [mem 0xf7e92000-0xf7ed2000] (0MB)
    [    0.000000] Memory: 3959404K/4061184K available (12478K kernel code, 1760K rwdata, 4552K rodata, 1216K init, 1962K bss, 101780K reserved, 0K cma-reserved)
    [    0.000000] Virtual kernel memory layout:
                       modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
                       vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000   (   246 GB)
                         .init : 0xffffff8009130000 - 0xffffff8009260000   (  1216 KB)
                         .text : 0xffffff8008080000 - 0xffffff8008cb0000   ( 12480 KB)
                       .rodata : 0xffffff8008cb0000 - 0xffffff8009130000   (  4608 KB)
                         .data : 0xffffff8009260000 - 0xffffff8009418008   (  1761 KB)
                       vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000   (     8 GB maximum)
                                 0xffffffbdc0008000 - 0xffffffbdc3e00000   (    61 MB actual)
                       fixed   : 0xffffffbffe7fb000 - 0xffffffbffec00000   (  4116 KB)
                       PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000   (    16 MB)
                       memory  : 0xffffffc000200000 - 0xffffffc0f8000000   (  3966 MB)
    [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
    [    0.000000] Hierarchical RCU implementation.
    [    0.000000] 	Build-time adjustment of leaf fanout to 64.
    [    0.000000] 	RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
    [    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6
    [    0.000000] NR_IRQS:64 nr_irqs:64 0
    [    0.000000] GIC: Using split EOI/Deactivate mode
    [    0.000000] ITS: /interrupt-controller@fee00000/interrupt-controller@fee20000
    [    0.000000] ITS: allocated 65536 Devices @f2900000 (psz 64K, shr 0)
    [    0.000000] ITS: using cache flushing for cmd queue
    [    0.000000] GIC: using LPI property table @0x00000000f2890000
    [    0.000000] ITS: Allocated 1792 chunks for LPIs
    [    0.000000] CPU0: found redistributor 0 region 0:0x00000000fef00000
    [    0.000000] CPU0: using LPI pending table @0x00000000f28a0000
    [    0.000000] GIC: using cache flushing for LPI property table
    [    0.000000] GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
    [    0.000000] GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
    [    0.000000] rockchip_mmc_get_phase: invalid clk rate
    [    0.000000] rockchip_mmc_get_phase: invalid clk rate
    [    0.000000] rockchip_mmc_get_phase: invalid clk rate
    [    0.000000] rockchip_mmc_get_phase: invalid clk rate
    [    0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop0_frac as parent of dclk_vop0, rate changes may not work
    [    0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop1_frac as parent of dclk_vop1, rate changes may not work
    [    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
    [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
    [    0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
    [    0.002174] Console: colour dummy device 80x25
    [    0.002605] console [tty0] enabled
    [    0.002940] bootconsole [uart0] disabled
    [    0.003336] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
    [    0.003364] pid_max: default: 32768 minimum: 301
    [    0.003490] Security Framework initialized
    [    0.003508] Yama: becoming mindful.
    [    0.003541] AppArmor: AppArmor disabled by boot time parameter
    [    0.003603] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
    [    0.003625] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
    [    0.004430] Initializing cgroup subsys io
    [    0.004456] Initializing cgroup subsys memory
    [    0.004496] Initializing cgroup subsys devices
    [    0.004517] Initializing cgroup subsys freezer
    [    0.004538] Initializing cgroup subsys net_cls
    [    0.004557] Initializing cgroup subsys perf_event
    [    0.004577] Initializing cgroup subsys net_prio
    [    0.004602] Initializing cgroup subsys hugetlb
    [    0.004619] Initializing cgroup subsys pids
    [    0.004668] ftrace: allocating 46093 entries in 181 pages
    [    0.130540] sched-energy: Sched-energy-costs installed from DT
    [    0.130572] CPU0: update cpu_capacity 401
    [    0.130641] ASID allocator initialised with 32768 entries
    [    0.133981] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
    [    0.134547] Platform MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
    [    0.135965] Detected VIPT I-cache on CPU1
    [    0.135997] CPU1: found redistributor 1 region 0:0x00000000fef20000
    [    0.136027] CPU1: using LPI pending table @0x00000000f2b40000
    [    0.136075] CPU1: update cpu_capacity 401
    [    0.136079] CPU1: Booted secondary processor [410fd034]
    [    0.136655] Detected VIPT I-cache on CPU2
    [    0.136676] CPU2: found redistributor 2 region 0:0x00000000fef40000
    [    0.136703] CPU2: using LPI pending table @0x00000000f2b90000
    [    0.136731] CPU2: update cpu_capacity 401
    [    0.136735] CPU2: Booted secondary processor [410fd034]
    [    0.137270] Detected VIPT I-cache on CPU3
    [    0.137290] CPU3: found redistributor 3 region 0:0x00000000fef60000
    [    0.137317] CPU3: using LPI pending table @0x00000000f2bd0000
    [    0.137342] CPU3: update cpu_capacity 401
    [    0.137346] CPU3: Booted secondary processor [410fd034]
    [    0.137943] Detected PIPT I-cache on CPU4
    [    0.137969] CPU4: found redistributor 100 region 0:0x00000000fef80000
    [    0.138012] CPU4: using LPI pending table @0x00000000f2000000
    [    0.138050] CPU4: update cpu_capacity 1024
    [    0.138053] CPU4: Booted secondary processor [410fd082]
    [    0.138621] Detected PIPT I-cache on CPU5
    [    0.138639] CPU5: found redistributor 101 region 0:0x00000000fefa0000
    [    0.138675] CPU5: using LPI pending table @0x00000000f2030000
    [    0.138701] CPU5: update cpu_capacity 1024
    [    0.138704] CPU5: Booted secondary processor [410fd082]
    [    0.138792] Brought up 6 CPUs
    [    0.139476] SMP: Total of 6 processors activated.
    [    0.139508] CPU features: detected feature: GIC system register CPU interface
    [    0.139543] CPU features: detected feature: 32-bit EL0 Support
    [    0.139579] CPU: All CPU(s) started at EL2
    [    0.139649] alternatives: patching kernel code
    [    0.141137] devtmpfs: initialized
    [    0.157938] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
    [    0.157997] futex hash table entries: 2048 (order: 5, 131072 bytes)
    [    0.158495] xor: measuring software checksum speed
    [    0.197553]    8regs     :  2855.000 MB/sec
    [    0.237619]    8regs_prefetch:  2561.000 MB/sec
    [    0.277684]    32regs    :  3191.000 MB/sec
    [    0.317749]    32regs_prefetch:  2840.000 MB/sec
    [    0.317769] xor: using function: 32regs (3191.000 MB/sec)
    [    0.317804] pinctrl core: initialized pinctrl subsystem
    [    0.318056] regulator-dummy: no parameters
    [    0.319454] Failed to find legacy iommu devices
    [    0.319883] NET: Registered protocol family 16
    [    0.331502] cpuidle: using governor ladder
    [    0.343524] cpuidle: using governor menu
    [    0.343560] Registered FIQ tty driver
    [    0.343962] vdso: 2 pages (1 code @ ffffff8008cb6000, 1 data @ ffffff8009264000)
    [    0.344020] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
    [    0.344565] DMA: preallocated 1024 KiB pool for atomic allocations
    [    0.360661] gpiochip_add_data: registered GPIOs 0 to 31 on device: gpio0
    [    0.360738] gpiochip_add_data: registered GPIOs 32 to 63 on device: gpio1
    [    0.360812] gpiochip_add_data: registered GPIOs 64 to 95 on device: gpio2
    [    0.360885] gpiochip_add_data: registered GPIOs 96 to 127 on device: gpio3
    [    0.360959] gpiochip_add_data: registered GPIOs 128 to 159 on device: gpio4
    [    0.454109] raid6: int64x1  gen()   474 MB/s
    [    0.522126] raid6: int64x1  xor()   417 MB/s
    [    0.590227] raid6: int64x2  gen()   655 MB/s
    [    0.658321] raid6: int64x2  xor()   593 MB/s
    [    0.726444] raid6: int64x4  gen()   917 MB/s
    [    0.794524] raid6: int64x4  xor()   671 MB/s
    [    0.862651] raid6: int64x8  gen()   751 MB/s
    [    0.930763] raid6: int64x8  xor()   622 MB/s
    [    0.998869] raid6: neonx1   gen()   995 MB/s
    [    1.066995] raid6: neonx1   xor()   670 MB/s
    [    1.135084] raid6: neonx2   gen()  1323 MB/s
    [    1.203201] raid6: neonx2   xor()   996 MB/s
    [    1.271297] raid6: neonx4   gen()  1760 MB/s
    [    1.339411] raid6: neonx4   xor()  1182 MB/s
    [    1.407535] raid6: neonx8   gen()  1694 MB/s
    [    1.475640] raid6: neonx8   xor()  1258 MB/s
    [    1.475659] raid6: using algorithm neonx4 gen() 1760 MB/s
    [    1.475678] raid6: .... xor() 1182 MB/s, rmw enabled
    [    1.475697] raid6: using intx1 recovery algorithm
    [    1.476696] of_get_named_gpiod_flags: parsed 'rockchip,power-ctrl' property of node '/rockchip-suspend[0]' - status (0)
    [    1.476736] of_get_named_gpiod_flags: parsed 'rockchip,power-ctrl' property of node '/rockchip-suspend[1]' - status (0)
    [    1.477029] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/dc-12v[0]'
    [    1.477052] dc_12v: 12000 mV 
    [    1.477230] reg-fixed-voltage dc-12v: dc_12v supplying 12000000uV
    [    1.477403] of_get_named_gpiod_flags: parsed 'gpio' property of node '/vcc3v3-pcie-regulator[0]' - status (0)
    [    1.477451] reg-fixed-voltage vcc3v3-pcie-regulator: Looking up vin-supply from device tree
    [    1.477494] vcc3v3_pcie: supplied by dc_12v
    [    1.477522] dc_12v: could not add device link regulator.2 err -2
    [    1.477564] vcc3v3_pcie: 3300 mV 
    [    1.477720] reg-fixed-voltage vcc3v3-pcie-regulator: vcc3v3_pcie supplying 3300000uV
    [    1.477774] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vcc1v8-s0[0]'
    [    1.477790] vcc1v8_s0: 1800 mV 
    [    1.477946] reg-fixed-voltage vcc1v8-s0: vcc1v8_s0 supplying 1800000uV
    [    1.477997] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vcc-sys[0]'
    [    1.478014] reg-fixed-voltage vcc-sys: Looking up vin-supply from device tree
    [    1.478049] vcc_sys: supplied by dc_12v
    [    1.478071] dc_12v: could not add device link regulator.4 err -2
    [    1.478099] vcc_sys: 5000 mV 
    [    1.478240] reg-fixed-voltage vcc-sys: vcc_sys supplying 5000000uV
    [    1.478289] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vcc-phy-regulator[0]'
    [    1.478304] vcc_phy: no parameters
    [    1.478460] reg-fixed-voltage vcc-phy-regulator: vcc_phy supplying 0uV
    [    1.478510] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vcc3v3-sys[0]'
    [    1.478531] reg-fixed-voltage vcc3v3-sys: Looking up vin-supply from device tree
    [    1.478569] vcc3v3_sys: supplied by vcc_sys
    [    1.478591] vcc_sys: could not add device link regulator.6 err -2
    [    1.478618] vcc3v3_sys: 3300 mV 
    [    1.478767] reg-fixed-voltage vcc3v3-sys: vcc3v3_sys supplying 3300000uV
    [    1.478907] of_get_named_gpiod_flags: parsed 'gpio' property of node '/vcc5v0-host-regulator[0]' - status (0)
    [    1.478947] vcc5v0_host: no parameters
    [    1.479111] reg-fixed-voltage vcc5v0-host-regulator: vcc5v0_host supplying 0uV
    [    1.479747] iommu: Adding device ff650000.vpu_service to group 0
    [    1.479848] iommu: Adding device ff660000.rkvdec to group 1
    [    1.479944] iommu: Adding device ff670000.iep to group 2
    [    1.480071] iommu: Adding device ff8f0000.vop to group 3
    [    1.480166] platform ff8f0000.vop: iommu /iommu@ff8f3f00 not found
    [    1.480186] iommu: Removing device ff8f0000.vop from group 3
    [    1.480251] iommu: Adding device ff900000.vop to group 3
    [    1.480772] rk_iommu ff650800.iommu: can't get sclk
    [    1.481077] rk_iommu ff660480.iommu: can't get sclk
    [    1.481191] rk_iommu ff670800.iommu: can't get aclk
    [    1.481214] rk_iommu ff670800.iommu: can't get hclk
    [    1.481235] rk_iommu ff670800.iommu: can't get sclk
    [    1.481437] rk_iommu ff903f00.iommu: can't get sclk
    [    1.481819] SCSI subsystem initialized
    [    1.482000] libata version 3.00 loaded.
    [    1.482178] usbcore: registered new interface driver usbfs
    [    1.482234] usbcore: registered new interface driver hub
    [    1.482332] usbcore: registered new device driver usb
    [    1.482448] media: Linux media interface: v0.10
    [    1.482501] Linux video capture interface: v2.00
    [    1.482618] pps_core: LinuxPPS API ver. 1 registered
    [    1.482638] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
    [    1.482681] PTP clock support registered
    [    1.483194] rockchip ion: success to create - cma-heap
    [    1.483223] rockchip ion: success to create - system-heap
    [    1.484433] Advanced Linux Sound Architecture Driver Initialized.
    [    1.484998] Bluetooth: Core ver 2.21
    [    1.485039] NET: Registered protocol family 31
    [    1.485059] Bluetooth: HCI device and connection manager initialized
    [    1.485084] Bluetooth: HCI socket layer initialized
    [    1.485107] Bluetooth: L2CAP socket layer initialized
    [    1.485147] Bluetooth: SCO socket layer initialized
    [    1.485540] NetLabel: Initializing
    [    1.485560] NetLabel:  domain hash size = 128
    [    1.485578] NetLabel:  protocols = UNLABELED CIPSOv4
    [    1.485627] NetLabel:  unlabeled traffic allowed by default
    [    1.486488] clocksource: Switched to clocksource arch_sys_counter
    [    1.553360] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
    [    1.553631] NET: Registered protocol family 2
    [    1.554108] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
    [    1.554396] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes)
    [    1.555256] TCP: Hash tables configured (established 32768 bind 32768)
    [    1.555393] UDP hash table entries: 2048 (order: 5, 196608 bytes)
    [    1.555562] UDP-Lite hash table entries: 2048 (order: 5, 196608 bytes)
    [    1.556009] NET: Registered protocol family 1
    [    1.556388] RPC: Registered named UNIX socket transport module.
    [    1.556411] RPC: Registered udp transport module.
    [    1.556430] RPC: Registered tcp transport module.
    [    1.556449] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [    1.556683] PCI: CLS 0 bytes, default 64
    [    1.557294] Trying to unpack rootfs image as initramfs...
    [    1.871086] Freeing initrd memory: 6440K
    [    1.871771] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
    [    1.871888] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
    [    1.873184] kvm [1]: 8-bit VMID
    [    1.873205] kvm [1]: Hyp mode initialized successfully
    [    1.873343] kvm [1]: interrupt-controller@fff20000 IRQ10
    [    1.873571] kvm [1]: timer IRQ12
    [    1.876845] audit: initializing netlink subsys (disabled)
    [    1.876904] audit: type=2000 audit(1.792:1): initialized
    [    1.877678] HugeTLB registered 2 MB page size, pre-allocated 0 pages
    [    1.885192] VFS: Disk quotas dquot_6.6.0
    [    1.885365] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    [    1.886858] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    [    1.888061] NFS: Registering the id_resolver key type
    [    1.888106] Key type id_resolver registered
    [    1.888125] Key type id_legacy registered
    [    1.888160] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
    [    1.888849] fuse init (API version 7.23)
    [    1.889601] JFS: nTxBlock = 8192, nTxLock = 65536
    [    1.895859] SGI XFS with ACLs, security attributes, realtime, no debug enabled
    [    1.898282] Key type big_key registered
    [    1.898369] 
                   TEE Core Framework initialization (ver 1:0.1)
    [    1.898414] TEE armv7 Driver initialization
    [    1.898944] tz_tee_probe: name="armv7sec", id=0, pdev_name="armv7sec.0"
    [    1.898970] TEE core: Alloc the misc device "opteearmtz00" (id=0)
    [    1.899171] TEE Core: Register the misc device "opteearmtz00" (id=0,minor=61)
    [    1.903361] NET: Registered protocol family 38
    [    1.903411] Key type asymmetric registered
    [    1.903437] Asymmetric key parser 'x509' registered
    [    1.903628] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
    [    1.903808] io scheduler noop registered
    [    1.903832] io scheduler deadline registered (default)
    [    1.903882] io scheduler cfq registered
    [    1.904885] phy phy-ff770000.syscon:usb2-phy@e460.0: Looking up phy-supply from device tree
    [    1.904989] vcc5v0_host: could not add device link phy-ff770000.syscon:usb2-phy@e460.0 err -2
    [    1.905311] phy phy-ff770000.syscon:usb2-phy@e460.1: Looking up phy-supply from device tree
    [    1.905322] phy phy-ff770000.syscon:usb2-phy@e460.1: Looking up phy-supply property in node /syscon@ff770000/usb2-phy@e460/otg-port failed
    [    1.905546] phy phy-ff770000.syscon:usb2-phy@e460.1: Looking up vbus-supply from device tree
    [    1.905557] phy phy-ff770000.syscon:usb2-phy@e460.1: Looking up vbus-supply property in node /syscon@ff770000/usb2-phy@e460/otg-port failed
    [    1.905570] phy phy-ff770000.syscon:usb2-phy@e460.1: Failed to get VBUS supply regulator
    [    1.907429] phy phy-ff770000.syscon:phy@f780.2: Looking up phy-supply from device tree
    [    1.907440] phy phy-ff770000.syscon:phy@f780.2: Looking up phy-supply property in node /syscon@ff770000/phy@f780 failed
    [    1.908291] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_tcpc0-supply from device tree
    [    1.908304] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_tcpc0-supply property in node /power-management@ff310000/power-controller failed
    [    1.908633] phy phy-ff800000.phy.3: Looking up phy-supply from device tree
    [    1.908643] phy phy-ff800000.phy.3: Looking up phy-supply property in node /phy@ff800000/dp-port failed
    [    1.908744] phy phy-ff800000.phy.4: Looking up phy-supply from device tree
    [    1.908753] phy phy-ff800000.phy.4: Looking up phy-supply property in node /phy@ff800000/usb3-port failed
    [    1.908851] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_tcpc1-supply from device tree
    [    1.908862] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_tcpc1-supply property in node /power-management@ff310000/power-controller failed
    [    1.909145] phy phy-pcie-phy.5: Looking up phy-supply from device tree
    [    1.909155] phy phy-pcie-phy.5: Looking up phy-supply property in node /pcie-phy failed
    [    1.910922] rockchip-pcie f8000000.pcie: GPIO lookup for consumer ep
    [    1.910932] rockchip-pcie f8000000.pcie: using device tree for GPIO lookup
    [    1.910961] of_get_named_gpiod_flags: parsed 'ep-gpios' property of node '/pcie@f8000000[0]' - status (0)
    [    1.911209] rockchip-pcie f8000000.pcie: Looking up vpcie3v3-supply from device tree
    [    1.911302] rockchip-pcie f8000000.pcie: Looking up vpcie1v8-supply from device tree
    [    1.911312] rockchip-pcie f8000000.pcie: Looking up vpcie1v8-supply property in node /pcie@f8000000 failed
    [    1.911326] rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found
    [    1.911356] rockchip-pcie f8000000.pcie: Looking up vpcie0v9-supply from device tree
    [    1.911365] rockchip-pcie f8000000.pcie: Looking up vpcie0v9-supply property in node /pcie@f8000000 failed
    [    1.911377] rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found
    [    1.911400] rockchip-pcie f8000000.pcie: bus-scan-delay-ms in device tree is 1000 ms
    [    1.911434] rockchip-pcie f8000000.pcie: missing "memory-region" property
    [    1.911472] PCI host bridge /pcie@f8000000 ranges:
    [    1.911506]   MEM 0xfa000000..0xfbdfffff -> 0xfa000000
    [    1.911530]    IO 0xfbe00000..0xfbefffff -> 0xfbe00000
    [    1.958509] rockchip-pcie f8000000.pcie: invalid power supply
    [    1.982703] rockchip-pcie f8000000.pcie: wait 1000 ms (from device tree) before bus scan
    [    2.986792] rockchip-pcie f8000000.pcie: PCI host bridge to bus 0000:00
    [    2.986837] pci_bus 0000:00: root bus resource [bus 00-1f]
    [    2.986874] pci_bus 0000:00: root bus resource [mem 0xfa000000-0xfbdfffff]
    [    2.986914] pci_bus 0000:00: root bus resource [io  0x0000-0xfffff] (bus address [0xfbe00000-0xfbefffff])
    [    2.987004] pci 0000:00:00.0: [1d87:0100] type 01 class 0x060400
    [    2.987119] pci 0000:00:00.0: supports D1
    [    2.987130] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
    [    2.987512] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
    [    2.987701] pci_bus 0000:01: busn_res: can not insert [bus 01-ff] under [bus 00-1f] (conflicts with (null) [bus 00-1f])
    [    2.987769] pci 0000:01:00.0: [1b4b:9230] type 00 class 0x010601
    [    2.987892] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00008000 invalid
    [    2.987930] pci 0000:01:00.0: reg 0x10: [io  size 0x0008]
    [    2.987973] pci 0000:01:00.0: reg 0x14: initial BAR value 0x00008040 invalid
    [    2.988008] pci 0000:01:00.0: reg 0x14: [io  size 0x0004]
    [    2.988051] pci 0000:01:00.0: reg 0x18: initial BAR value 0x00008100 invalid
    [    2.988087] pci 0000:01:00.0: reg 0x18: [io  size 0x0008]
    [    2.988129] pci 0000:01:00.0: reg 0x1c: initial BAR value 0x00008140 invalid
    [    2.988165] pci 0000:01:00.0: reg 0x1c: [io  size 0x0004]
    [    2.988208] pci 0000:01:00.0: reg 0x20: [io  0x800000-0x80001f]
    [    2.988251] pci 0000:01:00.0: reg 0x24: [mem 0x00900000-0x009007ff]
    [    2.988294] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0003ffff pref]
    [    2.988447] pci 0000:01:00.0: PME# supported from D3hot
    [    2.994562] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
    [    2.994608] pci 0000:00:00.0: BAR 8: assigned [mem 0xfa000000-0xfa0fffff]
    [    2.994654] pci 0000:01:00.0: BAR 6: assigned [mem 0xfa000000-0xfa03ffff pref]
    [    2.994721] pci 0000:01:00.0: BAR 5: assigned [mem 0xfa040000-0xfa0407ff]
    [    2.994768] pci 0000:01:00.0: BAR 4: no space for [io  size 0x0020]
    [    2.994804] pci 0000:01:00.0: BAR 4: failed to assign [io  size 0x0020]
    [    2.994840] pci 0000:01:00.0: BAR 0: no space for [io  size 0x0008]
    [    2.994875] pci 0000:01:00.0: BAR 0: failed to assign [io  size 0x0008]
    [    2.994911] pci 0000:01:00.0: BAR 2: no space for [io  size 0x0008]
    [    2.994947] pci 0000:01:00.0: BAR 2: failed to assign [io  size 0x0008]
    [    2.994983] pci 0000:01:00.0: BAR 1: no space for [io  size 0x0004]
    [    2.995018] pci 0000:01:00.0: BAR 1: failed to assign [io  size 0x0004]
    [    2.995054] pci 0000:01:00.0: BAR 3: no space for [io  size 0x0004]
    [    2.995089] pci 0000:01:00.0: BAR 3: failed to assign [io  size 0x0004]
    [    2.995126] pci 0000:00:00.0: PCI bridge to [bus 01]
    [    2.995164] pci 0000:00:00.0:   bridge window [mem 0xfa000000-0xfa0fffff]
    [    2.995273] pcieport 0000:00:00.0: enabling device (0000 -> 0002)
    [    2.995469] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt
    [    2.995505] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
    [    2.995544] pcie_pme 0000:00:00.0:pcie01: service driver pcie_pme loaded
    [    2.996578] iep: failed to find iep power down clock source.
    [    2.997222] IEP Power ON
    [    2.997462] IEP Power OFF
    [    2.997522] IEP Driver loaded succesfully
    [    2.997798] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_iep-supply from device tree
    [    2.997815] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_iep-supply property in node /power-management@ff310000/power-controller failed
    

  • [    2.997913] Module initialized.
    [    2.998360] rk-vcodec ff650000.vpu_service: Looking up vcodec-supply from device tree
    [    2.998374] rk-vcodec ff650000.vpu_service: Looking up vcodec-supply property in node /vpu_service@ff650000 failed
    [    2.998391] rk-vcodec ff650000.vpu_service: no regulator for vcodec
    [    2.998773] rk-vcodec ff650000.vpu_service: probe device
    [    2.999035] rk-vcodec ff650000.vpu_service: drm allocator with mmu enabled
    [    2.999583] rk-vcodec ff650000.vpu_service: could not find power_model node
    [    2.999608] rk-vcodec ff650000.vpu_service: init success
    [    2.999843] rk-vcodec ff660000.rkvdec: Looking up vcodec-supply from device tree
    [    2.999854] rk-vcodec ff660000.rkvdec: Looking up vcodec-supply property in node /rkvdec@ff660000 failed
    [    2.999870] rk-vcodec ff660000.rkvdec: no regulator for vcodec
    [    3.000311] rk-vcodec ff660000.rkvdec: probe device
    [    3.000519] rk-vcodec ff660000.rkvdec: drm allocator with mmu enabled
    [    3.000904] rk-vcodec ff660000.rkvdec: could not find power_model node
    [    3.000927] rk-vcodec ff660000.rkvdec: init success
    [    3.002385] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
    [    3.002422] dma-pl330 ff6d0000.dma-controller: 	DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
    [    3.003968] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
    [    3.004005] dma-pl330 ff6e0000.dma-controller: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
    [    3.004432] pwm-regulator vdd-log: GPIO lookup for consumer enable
    [    3.004440] pwm-regulator vdd-log: using device tree for GPIO lookup
    [    3.004450] of_get_named_gpiod_flags: can't parse 'enable-gpios' property of node '/vdd-log[0]'
    [    3.004459] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of node '/vdd-log[0]'
    [    3.004467] pwm-regulator vdd-log: using lookup tables for GPIO lookup
    [    3.004475] pwm-regulator vdd-log: lookup for GPIO enable failed
    [    3.004504] pwm-regulator vdd-log: Looking up pwm-supply from device tree
    [    3.004587] pwm-regulator: supplied by vcc_sys
    [    3.004611] vcc_sys: could not add device link regulator.8 err -2
    [    3.004687] vdd_log: 800 <--> 1400 mV at 896 mV 
    [    3.005321] Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled
    [    3.005947] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 36, base_baud = 1500000) is a 16550A
    [    3.006464] ff1a0000.serial: ttyS2 at MMIO 0xff1a0000 (irq = 37, base_baud = 1500000) is a 16550A
    [    3.156836] console [ttyS2] enabled
    [    3.158244] [drm] Initialized drm 1.1.0 20060810
    [    3.163095] [drm] Rockchip DRM driver version: v1.0.1
    [    3.164090] usbcore: registered new interface driver udl
    [    3.166162] Unable to detect cache hierarchy for CPU 0
    [    3.167461] brd: module loaded
    [    3.173040] loop: module loaded
    [    3.173380] lkdtm: No crash points registered, enable through debugfs
    [    3.174404] ahci 0000:01:00.0: version 3.0
    [    3.174470] ahci 0000:01:00.0: controller can do FBS, turning on CAP_FBS
    [    4.182516] ahci 0000:01:00.0: controller reset failed (0x80000001)
    [    4.183160] ahci: probe of 0000:01:00.0 failed with error -5
    [    4.185407] rockchip-spi ff1d0000.spi: no high_speed pinctrl state
    [    4.186709] m25p80 spi32766.0: gd25q128 (16384 Kbytes)
    [    4.187216] 3 ofpart partitions found on MTD device spi32766.0
    [    4.187756] Creating 3 MTD partitions on "spi32766.0":
    [    4.188238] 0x000000000000-0x0000003f8000 : "loader"
    [    4.190064] 0x0000003f8000-0x000000400000 : "env"
    [    4.191758] 0x0000007c0000-0x000000800000 : "vendor"
    [    4.196012] rk_gmac-dwmac fe300000.ethernet: Looking up phy-supply from device tree
    [    4.196132] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
    [    4.196787] rk_gmac-dwmac fe300000.ethernet: TX delay(0x28).
    [    4.197314] rk_gmac-dwmac fe300000.ethernet: RX delay(0x20).
    [    4.197861] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
    [    4.198718] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed
    [    4.199358] rk_gmac-dwmac fe300000.ethernet: clock input from PHY
    [    4.204930] rk_gmac-dwmac fe300000.ethernet: init for RGMII
    [    4.205616] stmmac - user ID: 0x10, Synopsys ID: 0x35
    [    4.206086]  Ring mode enabled
    [    4.206379]  DMA HW capability register supported
    [    4.206798]  Normal descriptors
    [    4.207135]  RX Checksum Offload Engine supported (type 2)
    [    4.207641]  TX Checksum insertion supported
    [    4.208041]  Enable RX Mitigation via HW Watchdog Timer
    [    4.208667] of_get_named_gpiod_flags: parsed 'snps,reset-gpio' property of node '/ethernet@fe300000[0]' - status (0)
    [    4.311209] libphy: stmmac: probed
    [    4.311541] eth%d: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active
    [    4.312134] eth%d: PHY ID 001cc916 at 1 IRQ POLL (stmmac-0:01)
    [    4.314860] Rockchip WiFi SYS interface (V1.00) ... 
    [    4.315448] usbcore: registered new interface driver cdc_ether
    [    4.316033] usbcore: registered new interface driver rndis_host
    [    4.318579] rockchip-dwc3 usb0: failed to get drvdata dwc3
    [    4.319222] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_usb3-supply from device tree
    [    4.319239] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_usb3-supply property in node /power-management@ff310000/power-controller failed
    [    4.324017] rockchip-dwc3 usb1: fail to get drvdata hcd
    [    4.326284] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [    4.326944] ehci-pci: EHCI PCI platform driver
    [    4.327446] ehci-platform: EHCI generic platform driver
    [    4.332049] ehci-platform fe3c0000.usb: EHCI Host Controller
    [    4.332831] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 1
    [    4.333707] ehci-platform fe3c0000.usb: irq 30, io mem 0xfe3c0000
    [    4.342521] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
    [    4.343322] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
    [    4.343948] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [    4.344628] usb usb1: Product: EHCI Host Controller
    [    4.345084] usb usb1: Manufacturer: Linux 4.4.202-1237-rockchip-ayufan-gfd4492386213 ehci_hcd
    [    4.345877] usb usb1: SerialNumber: fe3c0000.usb
    [    4.346977] hub 1-0:1.0: USB hub found
    [    4.347365] hub 1-0:1.0: 1 port detected
    [    4.348577] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    [    4.349165] ohci-platform: OHCI generic platform driver
    [    4.350381] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
    [    4.351286] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 2
    [    4.352136] ohci-platform fe3e0000.usb: irq 31, io mem 0xfe3e0000
    [    4.410720] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
    [    4.411347] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [    4.412027] usb usb2: Product: Generic Platform OHCI controller
    [    4.412575] usb usb2: Manufacturer: Linux 4.4.202-1237-rockchip-ayufan-gfd4492386213 ohci_hcd
    [    4.413366] usb usb2: SerialNumber: fe3e0000.usb
    [    4.414409] hub 2-0:1.0: USB hub found
    [    4.414817] hub 2-0:1.0: 1 port detected
    [    4.417915] usbcore: registered new interface driver iforce
    [    4.418607] usbcore: registered new interface driver xpad
    [    4.419565] usbcore: registered new interface driver usbtouchscreen
    [    4.420552] .. rk pwm remotectl v1.1 init
    [    4.421397] input: ff420030.pwm as /devices/platform/ff420030.pwm/input/input0
    [    4.423523] i2c /dev entries driver
    [    4.425057] fan53555-regulator 0-0040: GPIO lookup for consumer vsel
    [    4.425069] fan53555-regulator 0-0040: using device tree for GPIO lookup
    [    4.425111] of_get_named_gpiod_flags: parsed 'vsel-gpios' property of node '/i2c@ff3c0000/syr827@40[0]' - status (0)
    [    4.425537] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected!
    [    4.426187] fan53555-regulator 0-0040: Looking up vin-supply from device tree
    [    4.426268] fan53555-reg: supplied by vcc_sys
    [    4.426719] vcc_sys: could not add device link regulator.9 err -2
    [    4.428191] vdd_cpu_b: 712 <--> 1500 mV at 1000 mV 
    [    4.428928] fan53555-regulator 0-0041: GPIO lookup for consumer vsel
    [    4.428939] fan53555-regulator 0-0041: using device tree for GPIO lookup
    [    4.428978] of_get_named_gpiod_flags: parsed 'vsel-gpios' property of node '/i2c@ff3c0000/syr828@41[0]' - status (0)
    [    4.429360] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected!
    [    4.430003] fan53555-regulator 0-0041: Looking up vin-supply from device tree
    [    4.430064] fan53555-reg: supplied by vcc_sys
    [    4.430504] vcc_sys: could not add device link regulator.10 err -2
    [    4.432230] vdd_gpu: 712 <--> 1500 mV at 1000 mV 
    [    4.433361] rk808 0-001b: Pmic Chip id: 0x0
    [    4.437361] rk808 0-001b: GPIO lookup for consumer dvs
    [    4.437373] rk808 0-001b: using device tree for GPIO lookup
    [    4.437387] of_get_named_gpiod_flags: can't parse 'dvs-gpios' property of node '/i2c@ff3c0000/pmic@1b[0]'
    [    4.437399] of_get_named_gpiod_flags: can't parse 'dvs-gpio' property of node '/i2c@ff3c0000/pmic@1b[0]'
    [    4.437409] rk808 0-001b: using lookup tables for GPIO lookup
    [    4.437420] rk808 0-001b: lookup for GPIO dvs failed
    [    4.437432] rk808-regulator rk808-regulator: there is no dvs0 gpio
    [    4.438004] rk808 0-001b: GPIO lookup for consumer dvs
    [    4.438014] rk808 0-001b: using device tree for GPIO lookup
    [    4.438025] of_get_named_gpiod_flags: can't parse 'dvs-gpios' property of node '/i2c@ff3c0000/pmic@1b[1]'
    [    4.438037] of_get_named_gpiod_flags: can't parse 'dvs-gpio' property of node '/i2c@ff3c0000/pmic@1b[1]'
    [    4.438047] rk808 0-001b: using lookup tables for GPIO lookup
    [    4.438057] rk808 0-001b: lookup for GPIO dvs failed
    [    4.438067] rk808-regulator rk808-regulator: there is no dvs1 gpio
    [    4.438725] rk808 0-001b: Looking up vcc1-supply from device tree
    [    4.438829] DCDC_REG1: supplied by vcc_sys
    [    4.439221] vcc_sys: could not add device link regulator.11 err -2
    [    4.439721] vdd_center: 750 <--> 1350 mV at 900 mV 
    [    4.440085] rk808 0-001b: Looking up vcc2-supply from device tree
    [    4.440155] DCDC_REG2: supplied by vcc_sys
    [    4.440547] vcc_sys: could not add device link regulator.12 err -2
    [    4.440877] vdd_cpu_l: 750 <--> 1350 mV at 900 mV 
    [    4.441181] rk808 0-001b: Looking up vcc3-supply from device tree
    [    4.441236] DCDC_REG3: supplied by vcc_sys
    [    4.441627] vcc_sys: could not add device link regulator.13 err -2
    [    4.441700] vcc_ddr: at 5000 mV 
    [    4.441978] rk808 0-001b: Looking up vcc4-supply from device tree
    [    4.442030] DCDC_REG4: supplied by vcc_sys
    [    4.442422] vcc_sys: could not add device link regulator.14 err -2
    [    4.442672] vcc_1v8: 1800 mV 
    [    4.442990] rk808 0-001b: Looking up vcc6-supply from device tree
    [    4.443042] LDO_REG1: supplied by vcc_sys
    [    4.443426] vcc_sys: could not add device link regulator.15 err -2
    [    4.444284] vcc1v8_dvp: 1800 mV 
    [    4.444628] rk808 0-001b: Looking up vcc6-supply from device tree
    [    4.444681] LDO_REG2: supplied by vcc_sys
    [    4.445064] vcc_sys: could not add device link regulator.16 err -2
    [    4.445769] vcc3v0_touch: 3000 mV 
    [    4.446114] rk808 0-001b: Looking up vcc7-supply from device tree
    [    4.446167] LDO_REG3: supplied by vcc_sys
    [    4.446633] vcc_sys: could not add device link regulator.17 err -2
    [    4.447350] vcc1v8_pmu: 1800 mV 
    [    4.447710] rk808 0-001b: Looking up vcc9-supply from device tree
    [    4.447766] LDO_REG4: supplied by vcc_sys
    [    4.448150] vcc_sys: could not add device link regulator.18 err -2
    [    4.448863] vcc_sd: 1800 <--> 3300 mV at 3300 mV 
    [    4.449218] rk808 0-001b: Looking up vcc9-supply from device tree
    [    4.449270] LDO_REG5: supplied by vcc_sys
    [    4.449660] vcc_sys: could not add device link regulator.19 err -2
    [    4.450372] vcca3v0_codec: 3000 mV 
    [    4.450758] rk808 0-001b: Looking up vcc10-supply from device tree
    [    4.450813] LDO_REG6: supplied by vcc_sys
    [    4.451197] vcc_sys: could not add device link regulator.20 err -2
    [    4.451909] vcc_1v5: 1500 mV 
    [    4.452241] rk808 0-001b: Looking up vcc7-supply from device tree
    [    4.452293] LDO_REG7: supplied by vcc_sys
    [    4.452678] vcc_sys: could not add device link regulator.21 err -2
    [    4.453419] vcca1v8_codec: 1800 mV 
    [    4.453752] rk808 0-001b: Looking up vcc11-supply from device tree
    [    4.453805] LDO_REG8: supplied by vcc_sys
    [    4.454188] vcc_sys: could not add device link regulator.22 err -2
    [    4.454909] vcc_3v0: 3000 mV 
    [    4.455266] rk808 0-001b: Looking up vcc8-supply from device tree
    [    4.455320] SWITCH_REG1: supplied by vcc3v3_sys
    [    4.455750] vcc3v3_sys: could not add device link regulator.23 err -2
    [    4.455800] vcc3v3_s3: at 3300 mV 
    [    4.456126] rk808 0-001b: Looking up vcc12-supply from device tree
    [    4.456178] SWITCH_REG2: supplied by vcc3v3_sys
    [    4.456607] vcc3v3_sys: could not add device link regulator.24 err -2
    [    4.456772] vcc3v3_s0: at 3300 mV 
    [    4.460620] rk808-rtc rk808-rtc: rtc core: registered rk808-rtc as rtc0
    [    4.461716] rk3x-i2c ff3c0000.i2c: Initialized RK3xxx I2C bus at ffffff80096de000
    [    4.463405] rk3x-i2c ff110000.i2c: Initialized RK3xxx I2C bus at ffffff80096f2000
    [    4.465243] fusb302 4-0022: GPIO lookup for consumer int-n
    [    4.465256] fusb302 4-0022: using device tree for GPIO lookup
    [    4.465298] of_get_named_gpiod_flags: parsed 'int-n-gpios' property of node '/i2c@ff3d0000/fusb30x@22[0]' - status (0)
    [    4.465335] fusb302 4-0022: GPIO lookup for consumer vbus-5v
    [    4.465346] fusb302 4-0022: using device tree for GPIO lookup
    [    4.465380] of_get_named_gpiod_flags: parsed 'vbus-5v-gpios' property of node '/i2c@ff3d0000/fusb30x@22[0]' - status (0)
    [    4.465411] fusb302 4-0022: GPIO lookup for consumer vbus-other
    [    4.465422] fusb302 4-0022: using device tree for GPIO lookup
    [    4.465433] of_get_named_gpiod_flags: can't parse 'vbus-other-gpios' property of node '/i2c@ff3d0000/fusb30x@22[0]'
    [    4.465445] of_get_named_gpiod_flags: can't parse 'vbus-other-gpio' property of node '/i2c@ff3d0000/fusb30x@22[0]'
    [    4.465455] fusb302 4-0022: using lookup tables for GPIO lookup
    [    4.465466] fusb302 4-0022: lookup for GPIO vbus-other failed
    [    4.465477] fusb302 4-0022: GPIO lookup for consumer discharge
    [    4.465487] fusb302 4-0022: using device tree for GPIO lookup
    [    4.465498] of_get_named_gpiod_flags: can't parse 'discharge-gpios' property of node '/i2c@ff3d0000/fusb30x@22[0]'
    [    4.465509] of_get_named_gpiod_flags: can't parse 'discharge-gpio' property of node '/i2c@ff3d0000/fusb30x@22[0]'
    [    4.465519] fusb302 4-0022: using lookup tables for GPIO lookup
    [    4.465529] fusb302 4-0022: lookup for GPIO discharge failed
    [    4.465771] fusb302 4-0022: Can't get property of role, set role to default DRP
    [    4.474983] fusb302 4-0022: port 0 probe success with role ROLE_MODE_DRP, try_role ROLE_MODE_NONE
    [    4.475848] rk3x-i2c ff3d0000.i2c: Initialized RK3xxx I2C bus at ffffff80096f4000
    [    4.477264] rk3x-i2c ff3e0000.i2c: Initialized RK3xxx I2C bus at ffffff80096f6000
    [    4.479640] IR NEC protocol handler initialized
    [    4.480071] IR RC5(x/sz) protocol handler initialized
    [    4.480544] IR RC6 protocol handler initialized
    [    4.480971] IR JVC protocol handler initialized
    [    4.481398] IR Sony protocol handler initialized
    [    4.481834] IR SANYO protocol handler initialized
    [    4.482277] IR Sharp protocol handler initialized
    [    4.482757] IR MCE Keyboard/mouse protocol handler initialized
    [    4.483301] IR XMP protocol handler initialized
    [    4.484976] usbcore: registered new interface driver uvcvideo
    [    4.485506] USB Video Class driver (1.1.1)
    [    4.486712] rockchip-iodomain ff320000.syscon:io-domains: Looking up pmu1830-supply from device tree
    [    4.487075] rockchip-iodomain ff770000.syscon:io-domains: Looking up bt656-supply from device tree
    [    4.487155] rockchip-iodomain ff770000.syscon:io-domains: Looking up audio-supply from device tree
    [    4.487229] rockchip-iodomain ff770000.syscon:io-domains: Looking up sdmmc-supply from device tree
    [    4.487312] rockchip-iodomain ff770000.syscon:io-domains: Looking up gpio1830-supply from device tree
    [    4.490665] rk_tsadcv2_temp_to_code: Invalid conversion table: code=1023, temperature=2147483647
    [    4.491737] rockchip-thermal ff260000.tsadc: tsadc is probed successfully!
    [    4.494047] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
    [    4.494871] Bluetooth: Virtual HCI driver ver 1.5
    [    4.495403] Bluetooth: HCI UART driver ver 2.3
    [    4.495812] Bluetooth: HCI UART protocol H4 registered
    [    4.496279] Bluetooth: HCI UART protocol LL registered
    [    4.496743] Bluetooth: HCI UART protocol ATH3K registered
    [    4.497295] usbcore: registered new interface driver bfusb
    [    4.497844] usbcore: registered new interface driver btusb
    [    4.498933] cpu cpu0: leakage=16
    [    4.499258] cpu cpu0: Looking up cpu-supply from device tree
    [    4.500219] cpu cpu0: Failed to get pvtm
    [    4.500878] cpu cpu4: leakage=27
    [    4.501196] cpu cpu4: Looking up cpu-supply from device tree
    [    4.501919] cpu cpu4: Failed to get pvtm
    [    4.502605] cpu cpu0: Looking up cpu-supply from device tree
    [    4.502892] cpu cpu0: Looking up cpu-supply from device tree
    [    4.503559] cpu cpu0: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0
    [    4.504839] cpu cpu4: Looking up cpu-supply from device tree
    [    4.505561] cpu cpu4: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0
    [    4.508237] sdhci: Secure Digital Host Controller Interface driver
    [    4.508794] sdhci: Copyright(c) Pierre Ossman
    [    4.509196] Synopsys Designware Multimedia Card Interface Driver
    [    4.510719] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode.
    [    4.511408] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
    [    4.512028] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
    [    4.512589] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo
    [    4.513485] dwmmc_rockchip fe310000.dwmmc: 'clock-freq-min-max' property was deprecated.
    [    4.514221] dwmmc_rockchip fe310000.dwmmc: Looking up vmmc-supply from device tree
    [    4.514232] dwmmc_rockchip fe310000.dwmmc: Looking up vmmc-supply property in node /dwmmc@fe310000 failed
    [    4.514264] dwmmc_rockchip fe310000.dwmmc: Looking up vqmmc-supply from device tree
    [    4.514273] dwmmc_rockchip fe310000.dwmmc: Looking up vqmmc-supply property in node /dwmmc@fe310000 failed
    [    4.514294] dwmmc_rockchip fe310000.dwmmc: No vmmc regulator found
    [    4.514877] dwmmc_rockchip fe310000.dwmmc: No vqmmc regulator found
    [    4.515534] dwmmc_rockchip fe310000.dwmmc: GPIO lookup for consumer wp
    [    4.515542] dwmmc_rockchip fe310000.dwmmc: using device tree for GPIO lookup
    [    4.515553] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/dwmmc@fe310000[0]'
    [    4.515562] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/dwmmc@fe310000[0]'
    [    4.515570] dwmmc_rockchip fe310000.dwmmc: using lookup tables for GPIO lookup
    [    4.515578] dwmmc_rockchip fe310000.dwmmc: lookup for GPIO wp failed
    [    4.515784] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_sdioaudio-supply from device tree
    [    4.515795] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_sdioaudio-supply property in node /power-management@ff310000/power-controller failed
    [    4.516400] dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mode.
    [    4.517077] dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller.
    [    4.517696] dwmmc_rockchip fe320000.dwmmc: Version ID is 270a
    [    4.518248] dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 26,32 bit host data width,256 deep fifo
    [    4.519181] dwmmc_rockchip fe320000.dwmmc: 'clock-freq-min-max' property was deprecated.
    [    4.519918] dwmmc_rockchip fe320000.dwmmc: Looking up vmmc-supply from device tree
    [    4.519927] dwmmc_rockchip fe320000.dwmmc: Looking up vmmc-supply property in node /dwmmc@fe320000 failed
    [    4.519951] dwmmc_rockchip fe320000.dwmmc: Looking up vqmmc-supply from device tree
    [    4.520023] dwmmc_rockchip fe320000.dwmmc: No vmmc regulator found
    [    4.520591] dwmmc_rockchip fe320000.dwmmc: GPIO lookup for consumer cd
    [    4.520598] dwmmc_rockchip fe320000.dwmmc: using device tree for GPIO lookup
    [    4.520607] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/dwmmc@fe320000[0]'
    [    4.520616] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/dwmmc@fe320000[0]'
    [    4.520623] dwmmc_rockchip fe320000.dwmmc: using lookup tables for GPIO lookup
    [    4.520631] dwmmc_rockchip fe320000.dwmmc: lookup for GPIO cd failed
    [    4.520640] dwmmc_rockchip fe320000.dwmmc: GPIO lookup for consumer wp
    [    4.520647] dwmmc_rockchip fe320000.dwmmc: using device tree for GPIO lookup
    [    4.520655] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/dwmmc@fe320000[0]'
    [    4.520663] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/dwmmc@fe320000[0]'
    [    4.520669] dwmmc_rockchip fe320000.dwmmc: using lookup tables for GPIO lookup
    [    4.520677] dwmmc_rockchip fe320000.dwmmc: lookup for GPIO wp failed
    [    4.520835] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3300000 done
    [    4.521521] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3300000 done
    [    4.534540] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
    [    4.551745] dwmmc_rockchip fe320000.dwmmc: 1 slots initialized
    [    4.554899] sdhci-pltfm: SDHCI platform and OF driver helper
    [    4.558868] sdhci-arasan fe330000.sdhci: GPIO lookup for consumer wp
    [    4.558881] sdhci-arasan fe330000.sdhci: using device tree for GPIO lookup
    [    4.558894] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/sdhci@fe330000[0]'
    [    4.558907] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/sdhci@fe330000[0]'
    [    4.558917] sdhci-arasan fe330000.sdhci: using lookup tables for GPIO lookup
    [    4.558929] sdhci-arasan fe330000.sdhci: lookup for GPIO wp failed
    [    4.560061] sdhci-arasan fe330000.sdhci: Looking up vmmc-supply from device tree
    [    4.560076] sdhci-arasan fe330000.sdhci: Looking up vmmc-supply property in node /sdhci@fe330000 failed
    [    4.560121] sdhci-arasan fe330000.sdhci: Looking up vqmmc-supply from device tree
    [    4.560134] sdhci-arasan fe330000.sdhci: Looking up vqmmc-supply property in node /sdhci@fe330000 failed
    [    4.560156] sdhci-arasan fe330000.sdhci: No vmmc regulator found
    [    4.560714] sdhci-arasan fe330000.sdhci: No vqmmc regulator found
    [    4.594670] mmc1: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA
    [    4.596579] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/work-led[0]' - status (0)
    [    4.597846] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/standby-led[0]' - status (0)
    [    4.598176] hidraw: raw HID events driver (C) Jiri Kosina
    [    4.603851] usbcore: registered new interface driver usbhid
    [    4.604376] usbhid: USB HID core driver
    [    4.606828] rockchip-dmc dmc: unable to get devfreq-event device : dfi
    [    4.608744] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3300000 done
    [    4.609670] vcc_sd: ramp_delay not set
    [    4.609688] rockchip-iodomain ff770000.syscon:io-domains: Setting to 1800000 done
    [    4.612711] usbcore: registered new interface driver snd-usb-audio
    [    4.614891] of_get_named_gpiod_flags: can't parse 'spk-con-gpio' property of node '/i2c@ff110000/es8316@11[0]'
    [    4.614907] es8316 1-0011: Can not read property spk_ctl_gpio
    [    4.615486] of_get_named_gpiod_flags: parsed 'hp-det-gpio' property of node '/i2c@ff110000/es8316@11[0]' - status (0)
    [    4.624833] u32 classifier
    [    4.625126] Netfilter messages via NETLINK v0.30.
    [    4.625625] ip_set: protocol 6
    [    4.626135] Initializing XFRM netlink socket
    [    4.627225] NET: Registered protocol family 10
    [    4.628639] NET: Registered protocol family 17
    [    4.629074] NET: Registered protocol family 15
    [    4.629516] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
    

  • [    4.630711] Bridge firewalling registered
    [    4.631333] Bluetooth: RFCOMM socket layer initialized
    [    4.631831] Bluetooth: RFCOMM ver 1.11
    [    4.632193] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
    [    4.632739] Bluetooth: HIDP socket layer initialized
    [    4.633273] 8021q: 802.1Q VLAN Support v1.8
    [    4.633685] [WLAN_RFKILL]: Enter rfkill_wlan_init
    [    4.634644] [WLAN_RFKILL]: Enter rfkill_wlan_probe
    [    4.635168] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6354
    [    4.635791] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
    [    4.636436] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
    [    4.637123] of_get_named_gpiod_flags: can't parse 'WIFI,poweren_gpio' property of node '/wireless-wlan[0]'
    [    4.637132] of_get_named_gpiod_flags: can't parse 'WIFI,vbat_gpio' property of node '/wireless-wlan[0]'
    [    4.637141] of_get_named_gpiod_flags: can't parse 'WIFI,reset_gpio' property of node '/wireless-wlan[0]'
    [    4.637202] of_get_named_gpiod_flags: parsed 'WIFI,host_wake_irq' property of node '/wireless-wlan[0]' - status (0)
    [    4.637209] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,host_wake_irq = 3, flags = 0.
    [    4.637330] mmc_host mmc0: Bus speed (slot 0) = 150000000Hz (slot req 150000000Hz, actual 150000000HZ div = 0)
    [    4.638960] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
    [    4.639635] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
    [    4.640117] [WLAN_RFKILL]: Exit rfkill_wlan_probe
    [    4.640638] [BT_RFKILL]: Enter rfkill_rk_init
    [    4.641685] of_get_named_gpiod_flags: parsed 'uart_rts_gpios' property of node '/wireless-bluetooth[0]' - status (0)
    [    4.641694] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 83.
    [    4.642445] of_get_named_gpiod_flags: can't parse 'BT,power_gpio' property of node '/wireless-bluetooth[0]'
    [    4.642474] of_get_named_gpiod_flags: parsed 'BT,reset_gpio' property of node '/wireless-bluetooth[0]' - status (0)
    [    4.642523] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 9.
    [    4.643284] of_get_named_gpiod_flags: parsed 'BT,wake_gpio' property of node '/wireless-bluetooth[0]' - status (0)
    [    4.643291] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 91.
    [    4.644039] of_get_named_gpiod_flags: parsed 'BT,wake_host_irq' property of node '/wireless-bluetooth[0]' - status (0)
    [    4.644046] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 4.
    [    4.649156] [BT_RFKILL]: Request irq for bt wakeup host
    [    4.649724] [BT_RFKILL]: ** disable irq
    [    4.650264] [BT_RFKILL]: bt_default device registered.
    [    4.650917] Key type dns_resolver registered
    [    4.652294] Registered cp15_barrier emulation handler
    [    4.652895] Registered setend emulation handler
    [    4.655746] registered taskstats version 1
    [    4.658830] Btrfs loaded, integrity-checker=on
    [    4.659396] BTRFS: selftest: Running btrfs free space cache tests
    [    4.659973] BTRFS: selftest: Running extent only tests
    [    4.660464] BTRFS: selftest: Running bitmap only tests
    [    4.660953] BTRFS: selftest: Running bitmap and extent tests
    [    4.661490] BTRFS: selftest: Running space stealing from bitmap to extent
    [    4.663322] BTRFS: selftest: Free space cache tests finished
    [    4.663840] BTRFS: selftest: Running extent buffer operation tests
    [    4.664371] BTRFS: selftest: Running btrfs_split_item tests
    [    4.664961] BTRFS: selftest: Running find delalloc tests
    [    4.885776] BTRFS: selftest: Running btrfs_get_extent tests
    [    4.886453] BTRFS: selftest: Running hole first btrfs_get_extent test
    [    4.887133] BTRFS: selftest: Running outstanding_extents tests
    [    4.887690] BTRFS: selftest: Running qgroup tests
    [    4.888110] BTRFS: selftest: Qgroup basic add
    [    4.888539] BTRFS: selftest: Qgroup multiple refs test
    [    4.905877] dwmmc_rockchip fe320000.dwmmc: Successfully tuned phase to 264
    [    4.906677] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
    [    4.908843] mmcblk0: mmc0:aaaa SL64G 59.5 GiB 
    [    4.921033]  mmcblk0: p1 p2 p3 p4 p5 p6 p7
    [    4.938763] Key type encrypted registered
    [    4.940192] rga2 ff680000.rga: rga ion client create success!
    [    4.940872] rga: Driver loaded successfully ver:3.02
    [    4.941473] rga2: Module initialized.
    [    4.941881] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_rga-supply from device tree
    [    4.941891] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_rga-supply property in node /power-management@ff310000/power-controller failed
    [    4.942671] phy phy-ff770000.syscon:usb2-phy@e450.6: Looking up phy-supply from device tree
    [    4.942752] vcc5v0_host: could not add device link phy-ff770000.syscon:usb2-phy@e450.6 err -2
    [    4.943461] phy phy-ff770000.syscon:usb2-phy@e450.7: Looking up phy-supply from device tree
    [    4.943470] phy phy-ff770000.syscon:usb2-phy@e450.7: Looking up phy-supply property in node /syscon@ff770000/usb2-phy@e450/otg-port failed
    [    4.944152] phy phy-ff770000.syscon:usb2-phy@e450.7: Looking up vbus-supply from device tree
    [    4.944161] phy phy-ff770000.syscon:usb2-phy@e450.7: Looking up vbus-supply property in node /syscon@ff770000/usb2-phy@e450/otg-port failed
    [    4.944177] phy phy-ff770000.syscon:usb2-phy@e450.7: Failed to get VBUS supply regulator
    [    4.945963] phy phy-ff7c0000.phy.8: Looking up phy-supply from device tree
    [    4.945971] phy phy-ff7c0000.phy.8: Looking up phy-supply property in node /phy@ff7c0000/dp-port failed
    [    4.946062] phy phy-ff7c0000.phy.9: Looking up phy-supply from device tree
    [    4.946068] phy phy-ff7c0000.phy.9: Looking up phy-supply property in node /phy@ff7c0000/usb3-port failed
    [    4.946540] rockchip-drm display-subsystem: devfreq is not set
    [    4.947307] rockchip-vop ff900000.vop: missing rockchip,grf property
    [    4.948067] rockchip-drm display-subsystem: bound ff900000.vop (ops 0xffffff8008d86950)
    [    4.948812] rockchip-vop ff8f0000.vop: missing rockchip,grf property
    [    4.949512] rockchip-drm display-subsystem: bound ff8f0000.vop (ops 0xffffff8008d86950)
    [    4.951020] i2c i2c-9: of_i2c: modalias failure on /hdmi@ff940000/ports
    [    4.951735] dwhdmi-rockchip ff940000.hdmi: registered DesignWare HDMI I2C bus driver
    [    4.952862] dwhdmi-rockchip ff940000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
    [    4.958247] rockchip-drm display-subsystem: bound ff940000.hdmi (ops 0xffffff8008d7afa8)
    [    4.960616] i2c i2c-10: of_i2c: modalias failure on /dp@fec00000/ports
    [    4.962187] cdn-dp fec00000.dp: Direct firmware load for rockchip/dptx.bin failed with error -2
    [    4.963249] rockchip-drm display-subsystem: bound fec00000.dp (ops 0xffffff8008d7bf80)
    [    4.964046] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
    [    4.964685] [drm] No driver support for vblank timestamp query.
    [    4.965510] rockchip-drm display-subsystem: failed to parse display resources
    [    4.966298] rockchip-drm display-subsystem: No connectors reported connected with modes
    [    4.967228] [drm] Cannot find any crtc or sizes - going 1024x768
    [    4.998595] Console: switching to colour frame buffer device 128x48
    [    5.013037] rockchip-drm display-subsystem: fb0:  frame buffer device
    [    5.034854] rockchip-typec-phy ff7c0000.phy: Needed 1 loops to turn on
    [    5.035854] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
    [    5.036875] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 3
    [    5.037882] xhci-hcd xhci-hcd.9.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x06030010
    [    5.038942] xhci-hcd xhci-hcd.9.auto: irq 232, io mem 0xfe800000
    [    5.039894] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
    [    5.040651] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [    5.041450] usb usb3: Product: xHCI Host Controller
    [    5.041995] usb usb3: Manufacturer: Linux 4.4.202-1237-rockchip-ayufan-gfd4492386213 xhci-hcd
    [    5.042997] usb usb3: SerialNumber: xhci-hcd.9.auto
    [    5.044302] hub 3-0:1.0: USB hub found
    [    5.044759] hub 3-0:1.0: 1 port detected
    [    5.045530] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
    [    5.046442] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 4
    [    5.047375] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
    [    5.048374] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
    [    5.049129] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [    5.049928] usb usb4: Product: xHCI Host Controller
    [    5.050472] usb usb4: Manufacturer: Linux 4.4.202-1237-rockchip-ayufan-gfd4492386213 xhci-hcd
    [    5.051470] usb usb4: SerialNumber: xhci-hcd.9.auto
    [    5.052762] hub 4-0:1.0: USB hub found
    [    5.053212] hub 4-0:1.0: 1 port detected
    [    5.060962] xhci-hcd xhci-hcd.9.auto: remove, state 1
    [    5.066371] usb usb4: USB disconnect, device number 1
    [    5.088365] xhci-hcd xhci-hcd.9.auto: Host not halted after 16000 microseconds.
    [    5.093816] xhci-hcd xhci-hcd.9.auto: Host controller not halted, aborting reset.
    [    5.099300] xhci-hcd xhci-hcd.9.auto: USB bus 4 deregistered
    [    5.104957] xhci-hcd xhci-hcd.9.auto: remove, state 1
    [    5.110070] usb usb3: USB disconnect, device number 1
    [    5.116050] xhci-hcd xhci-hcd.9.auto: USB bus 3 deregistered
    [    5.125549] xhci-hcd xhci-hcd.10.auto: xHCI Host Controller
    [    5.130357] xhci-hcd xhci-hcd.10.auto: new USB bus registered, assigned bus number 3
    [    5.135013] xhci-hcd xhci-hcd.10.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x06030010
    [    5.139644] xhci-hcd xhci-hcd.10.auto: irq 233, io mem 0xfe900000
    [    5.144152] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
    [    5.148527] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [    5.152882] usb usb3: Product: xHCI Host Controller
    [    5.156980] usb usb3: Manufacturer: Linux 4.4.202-1237-rockchip-ayufan-gfd4492386213 xhci-hcd
    [    5.161482] usb usb3: SerialNumber: xhci-hcd.10.auto
    [    5.166933] hub 3-0:1.0: USB hub found
    [    5.173706] hub 3-0:1.0: 1 port detected
    [    5.180931] xhci-hcd xhci-hcd.10.auto: xHCI Host Controller
    [    5.188022] xhci-hcd xhci-hcd.10.auto: new USB bus registered, assigned bus number 4
    [    5.192511] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
    [    5.196497] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
    [    5.200261] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [    5.204047] usb usb4: Product: xHCI Host Controller
    [    5.207603] usb usb4: Manufacturer: Linux 4.4.202-1237-rockchip-ayufan-gfd4492386213 xhci-hcd
    [    5.211541] usb usb4: SerialNumber: xhci-hcd.10.auto
    [    5.215579] hub 4-0:1.0: USB hub found
    [    5.219095] hub 4-0:1.0: 1 port detected
    [    5.226630] ehci-platform fe380000.usb: EHCI Host Controller
    [    5.230416] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 5
    [    5.234359] ehci-platform fe380000.usb: irq 28, io mem 0xfe380000
    [    5.246679] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
    [    5.250535] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
    [    5.254189] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [    5.257870] usb usb5: Product: EHCI Host Controller
    [    5.261332] usb usb5: Manufacturer: Linux 4.4.202-1237-rockchip-ayufan-gfd4492386213 ehci_hcd
    [    5.265229] usb usb5: SerialNumber: fe380000.usb
    [    5.269300] hub 5-0:1.0: USB hub found
    [    5.272335] hub 5-0:1.0: 1 port detected
    [    5.275866] ohci-platform fe3a0000.usb: Generic Platform OHCI controller
    [    5.279154] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 6
    [    5.282429] ohci-platform fe3a0000.usb: irq 29, io mem 0xfe3a0000
    [    5.343132] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
    [    5.355856] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [    5.368473] usb usb6: Product: Generic Platform OHCI controller
    [    5.381095] usb usb6: Manufacturer: Linux 4.4.202-1237-rockchip-ayufan-gfd4492386213 ohci_hcd
    [    5.394255] usb usb6: SerialNumber: fe3a0000.usb
    [    5.408268] hub 6-0:1.0: USB hub found
    [    5.413602] hub 6-0:1.0: 1 port detected
    [    5.420466] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode.
    [    5.426178] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
    [    5.431771] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
    [    5.437274] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo
    [    5.443239] dwmmc_rockchip fe310000.dwmmc: 'clock-freq-min-max' property was deprecated.
    [    5.449038] dwmmc_rockchip fe310000.dwmmc: Looking up vmmc-supply from device tree
    [    5.449051] dwmmc_rockchip fe310000.dwmmc: Looking up vmmc-supply property in node /dwmmc@fe310000 failed
    [    5.449106] dwmmc_rockchip fe310000.dwmmc: Looking up vqmmc-supply from device tree
    [    5.449117] dwmmc_rockchip fe310000.dwmmc: Looking up vqmmc-supply property in node /dwmmc@fe310000 failed
    [    5.449135] dwmmc_rockchip fe310000.dwmmc: No vmmc regulator found
    [    5.454755] dwmmc_rockchip fe310000.dwmmc: No vqmmc regulator found
    [    5.460347] dwmmc_rockchip fe310000.dwmmc: GPIO lookup for consumer wp
    [    5.460357] dwmmc_rockchip fe310000.dwmmc: using device tree for GPIO lookup
    [    5.460368] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/dwmmc@fe310000[0]'
    [    5.460379] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/dwmmc@fe310000[0]'
    [    5.460387] dwmmc_rockchip fe310000.dwmmc: using lookup tables for GPIO lookup
    [    5.460397] dwmmc_rockchip fe310000.dwmmc: lookup for GPIO wp failed
    [    5.460665] platform sdio-pwrseq: GPIO lookup for consumer reset
    [    5.460672] platform sdio-pwrseq: using device tree for GPIO lookup
    [    5.460697] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/sdio-pwrseq[0]' - status (0)
    [    5.460742] dwmmc_rockchip fe310000.dwmmc: allocated mmc-pwrseq
    [    5.478587] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
    [    5.498958] dwmmc_rockchip fe310000.dwmmc: 1 slots initialized
    [    5.516569] rockchip-dmc dmc: Looking up center-supply from device tree
    [    5.517197] rockchip-dmc dmc: Failed to get leakage
    [    5.530311] rockchip-dmc dmc: Looking up center-supply from device tree
    [    5.530401] vdd_center: could not add device link dmc err -17
    [    5.530430] vdd_center: Failed to create debugfs directory
    [    5.533125] rockchip-dmc dmc: Failed to get pvtm
    [    5.540551] rockchip-dmc dmc: failed to get vop pn to msch rl
    [    5.546244] rockchip-dmc dmc: could not find power_model node
    [    5.552286] of_get_named_gpiod_flags: parsed 'simple-audio-card,hp-det-gpio' property of node '/headphones-sound[0]' - status (0)
    [    5.552297] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/headphones-sound[0]'
    [    5.554582] mmc_host mmc2: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0)
    [    5.602906] mmc_host mmc2: Bus speed (slot 0) = 200000Hz (slot req 200000Hz, actual 200000HZ div = 0)
    [    5.695304] asoc-simple-card headphones-sound: ASoC: DAPM unknown pin Headphones
    [    5.700967] gpio-8 (hp det): gpiod_request: status -16
    [    5.702808] asoc-simple-card headphones-sound: ES8316 HiFi <-> ff890000.i2s mapping ok
    [    5.708749] es8316 1-0011: ASoC: Failed to create Left Hp mixer debugfs file
    [    5.714348] es8316 1-0011: ASoC: Failed to create Right Hp mixer debugfs file
    [    5.719897] es8316 1-0011: ASoC: Failed to create HPCP L debugfs file
    [    5.725327] es8316 1-0011: ASoC: Failed to create HPCP R debugfs file
    [    5.730708] es8316 1-0011: ASoC: Failed to create HPVOL L debugfs file
    [    5.735651] es8316 1-0011: ASoC: Failed to create HPVOL R debugfs file
    [    5.742835] input: rk-es8316-hp-sound Headphones as /devices/platform/headphones-sound/sound/card0/input1
    [    5.750192] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/spdif-sound[0]'
    [    5.750202] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/spdif-sound[0]'
    [    5.750780] asoc-simple-card spdif-sound: dit-hifi <-> ff870000.spdif mapping ok
    [    5.759098] rk-hdmi-dp-sound hdmi-sound: control 3:0:0:ELD:0 is already present
    [    5.763841] hdmi-audio-codec hdmi-audio-codec.8.auto: ASoC: Failed to add ELD: -16
    [    5.769100] rk-hdmi-dp-sound hdmi-sound: multicodec <-> ff8a0000.i2s mapping ok
    [    5.773971] hdmi-audio-codec hdmi-audio-codec.8.auto: ASoC: Failed to create Playback debugfs file
    [    5.781389] input: rk-hdmi-dp-sound /hdmi@ff940000 Jack as /devices/platform/hdmi-sound/sound/card2/input2
    [    5.786846] input: rk-hdmi-dp-sound /dp@fec00000 Jack as /devices/platform/hdmi-sound/sound/card2/input3
    [    5.794693] of_get_named_gpiod_flags: parsed 'gpios' property of node '/gpio-keys/power[0]' - status (0)
    [    5.794748] gpio-5 (Power): gpiod_set_debounce: missing set() or set_debounce() operations
    [    5.794979] input: gpio-keys as /devices/platform/gpio-keys/input/input4
    [    5.799462] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_vopl-supply from device tree
    [    5.799473] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_vopl-supply property in node /power-management@ff310000/power-controller failed
    [    5.799542] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_isp1-supply from device tree
    [    5.799550] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_isp1-supply property in node /power-management@ff310000/power-controller failed
    [    5.799586] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_isp0-supply from device tree
    [    5.799594] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_isp0-supply property in node /power-management@ff310000/power-controller failed
    [    5.799651] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_edp-supply from device tree
    [    5.799659] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_edp-supply property in node /power-management@ff310000/power-controller failed
    [    5.799693] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_gpu-supply from device tree
    [    5.799702] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_gpu-supply property in node /power-management@ff310000/power-controller failed
    [    5.801779] rk808-rtc rk808-rtc: setting system clock to 2013-01-18 08:50:13 UTC (1358499013)
    [    5.806375] of_cfs_init
    [    5.810281] of_cfs_init: OK
    [    5.833404] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_vopb-supply from device tree
    [    5.833430] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_vopb-supply property in node /power-management@ff310000/power-controller failed
    [    5.833556] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_vo-supply from device tree
    [    5.833564] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_vo-supply property in node /power-management@ff310000/power-controller failed
    [    5.833616] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_vdu-supply from device tree
    [    5.833623] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_vdu-supply property in node /power-management@ff310000/power-controller failed
    [    5.833670] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_vcodec-supply from device tree
    [    5.833677] rockchip-pm-domain ff310000.power-management:power-controller: Looking up pd_vcodec-supply property in node /power-management@ff310000/power-controller failed
    [    5.834710] ALSA device list:
    [    5.838414]   #0: rk-es8316-hp-sound
    [    5.842088]   #1: rk-spdif-sound
    [    5.845688]   #2: rk-hdmi-dp-sound
    [    5.850128] Freeing unused kernel memory: 1216K
    [    5.966780] cdn-dp fec00000.dp: Direct firmware load for rockchip/dptx.bin failed with error -2
    [    6.393838] md: linear personality registered for level -1
    [    6.416929] md: multipath personality registered for level -4
    [    6.428600] md: raid0 personality registered for level 0
    [    6.451032] md: raid1 personality registered for level 1
    [    6.473718] async_tx: api initialized (async)
    [    6.486830] md: raid6 personality registered for level 6
    [    6.493489] md: raid5 personality registered for level 5
    [    6.497313] md: raid4 personality registered for level 4
    [    6.528661] md: raid10 personality registered for level 10
    [    7.006732] iep dpi mode inactivity
    [    7.072698] EXT4-fs (mmcblk0p7): mounted filesystem with writeback data mode. Opts: (null)
    [    7.600471] systemd[1]: System time before build time, advancing clock.
    [    7.668965] systemd[1]: Inserted module 'autofs4'
    [    7.709079] ip_tables: (C) 2000-2006 Netfilter Core Team
    [    7.732127] cgroup: cgroup2: unknown option "nsdelegate"
    [    7.776875] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
    [    7.805905] systemd[1]: Detected architecture arm64.
    [    7.848141] systemd[1]: Set hostname to <cloud>.
    [    7.994733] cdn-dp fec00000.dp: Direct firmware load for rockchip/dptx.bin failed with error -2
    [    8.370109] systemd[1]: File /lib/systemd/system/systemd-journald.service:12 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
    [    8.390463] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
    [    8.749409] systemd[1]: /lib/systemd/system/rpc-statd.service:13: PIDFile= references path below legacy directory /var/run/, updating /var/run/rpc.statd.pid \xe2\x86\x92 /run/rpc.statd.pid; please update the unit file accordingly.
    [    8.817743] systemd[1]: /lib/systemd/system/fail2ban.service:12: PIDFile= references path below legacy directory /var/run/, updating /var/run/fail2ban/fail2ban.pid \xe2\x86\x92 /run/fail2ban/fail2ban.pid; please update the unit file accordingly.