Skip to content
linux-nerds.org

linux-nerds.org
  1. Übersicht
  2. Pine64
  3. ROCKPro64
  4. ROCKPro64 - USB3 Probleme

ROCKPro64 - USB3 Probleme

ROCKPro64
  • FrankMF

    Nehmen wir einen uralten USB2-Stick, Größe 8GB und flashen Kamil's letztes Image drauf. Ab in den USB3-Port und starten.

    USB2-Stick am USB3-Port

    System

    rock64@rockpro64:~$ uname -a
Linux rockpro64 4.4.132-1075-rockchip-ayufan-ga83beded8524 #1 SMP Thu Jul 26 08:22:22 UTC 2018 aarch64 aarch64 aarch64 GNU/Linux

    lsusb

    rock64@rockpro64:~$ lsusb
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 002: ID 090c:1000 Silicon Motion, Inc. - Taiwan (formerly Feiya Technology Corp.) Flash Drive
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

    fdisk

     Disk /dev/sda: 7.5 GiB, 8022654976 bytes, 15669248 sectors
 Units: sectors of 1 * 512 = 512 bytes
 Sector size (logical/physical): 512 bytes / 512 bytes
 I/O size (minimum/optimal): 512 bytes / 512 bytes
 Disklabel type: gpt
 Disk identifier: 2C9A4A22-7AA8-4A1B-815E-0C3E2E7065E6
 
 Device      Start      End  Sectors  Size Type
 /dev/sda1      64     8063     8000  3.9M Linux filesystem
 /dev/sda2    8064     8191      128   64K Linux filesystem
 /dev/sda3    8192    16383     8192    4M Linux filesystem
 /dev/sda4   16384    24575     8192    4M Linux filesystem
 /dev/sda5   24576    32767     8192    4M Linux filesystem
 /dev/sda6   32768   262143   229376  112M Microsoft basic data
 /dev/sda7  262144 15669214 15407071  7.4G Linux filesystem

    dmesg

    rock64@rockpro64:~$ sudo dmesg | grep -i usb
[    0.506700] usbcore: registered new interface driver usbfs
[    0.506756] usbcore: registered new interface driver hub
[    0.506852] usbcore: registered new device driver usb
[    0.909861] phy phy-ff770000.syscon:usb2-phy@e460.0: Looking up phy-supply from device tree
[    0.909874] phy phy-ff770000.syscon:usb2-phy@e460.0: Looking up phy-supply property in node /syscon@ff770000/usb2-phy@e460/otg-port failed
[    0.910150] phy phy-ff770000.syscon:usb2-phy@e460.0: Looking up vbus-supply from device tree
[    0.910161] phy phy-ff770000.syscon:usb2-phy@e460.0: Looking up vbus-supply property in node /syscon@ff770000/usb2-phy@e460/otg-port failed
[    0.910174] phy phy-ff770000.syscon:usb2-phy@e460.0: Failed to get VBUS supply regulator
[    0.910358] phy phy-ff770000.syscon:usb2-phy@e460.1: Looking up phy-supply from device tree
[    0.910440] vcc5v0_host: could not add device link phy-ff770000.syscon:usb2-phy@e460.1 err -2
[    0.912857] phy phy-ff800000.phy.4: Looking up phy-supply property in node /phy@ff800000/usb3-port failed
[    1.044647] usbcore: registered new interface driver udl
[    1.151977] usbcore: registered new interface driver cdc_ether
[    1.152585] usbcore: registered new interface driver rndis_host
[    1.155022] rockchip-dwc3 usb@fe800000: failed to get drvdata dwc3
[    1.161158] rockchip-dwc3 usb@fe900000: fail to get drvdata hcd
[    1.163433] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.169174] ehci-platform fe3c0000.usb: EHCI Host Controller
[    1.169931] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 1
[    1.170823] ehci-platform fe3c0000.usb: irq 29, io mem 0xfe3c0000
[    1.177217] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
[    1.178021] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.178666] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.179363] usb usb1: Product: EHCI Host Controller
[    1.179823] usb usb1: Manufacturer: Linux 4.4.132-1075-rockchip-ayufan-ga83beded8524 ehci_hcd
[    1.180631] usb usb1: SerialNumber: fe3c0000.usb
[    1.181678] hub 1-0:1.0: USB hub found
[    1.183295] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.185080] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
[    1.185923] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 2
[    1.186791] ohci-platform fe3e0000.usb: irq 30, io mem 0xfe3e0000
[    1.242415] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    1.243045] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.243742] usb usb2: Product: Generic Platform OHCI controller
[    1.244307] usb usb2: Manufacturer: Linux 4.4.132-1075-rockchip-ayufan-ga83beded8524 ohci_hcd
[    1.245104] usb usb2: SerialNumber: fe3e0000.usb
[    1.246158] hub 2-0:1.0: USB hub found
[    1.249659] usbcore: registered new interface driver iforce
[    1.250247] usbcore: registered new interface driver xpad
[    1.251035] usbcore: registered new interface driver usbtouchscreen
[    1.294313] fusb302 4-0022: GPIO lookup for consumer int-n
[    1.294325] fusb302 4-0022: using device tree for GPIO lookup
[    1.294366] of_get_named_gpiod_flags: parsed 'int-n-gpios' property of node '/i2c@ff3d0000/fusb30x@22[0]' - status (0)
[    1.294400] fusb302 4-0022: GPIO lookup for consumer vbus-5v
[    1.294410] fusb302 4-0022: using device tree for GPIO lookup
[    1.294442] of_get_named_gpiod_flags: parsed 'vbus-5v-gpios' property of node '/i2c@ff3d0000/fusb30x@22[0]' - status (0)
[    1.294473] fusb302 4-0022: GPIO lookup for consumer vbus-other
[    1.294482] fusb302 4-0022: using device tree for GPIO lookup
[    1.294494] of_get_named_gpiod_flags: can't parse 'vbus-other-gpios' property of node '/i2c@ff3d0000/fusb30x@22[0]'
[    1.294505] of_get_named_gpiod_flags: can't parse 'vbus-other-gpio' property of node '/i2c@ff3d0000/fusb30x@22[0]'
[    1.294515] fusb302 4-0022: using lookup tables for GPIO lookup
[    1.294525] fusb302 4-0022: lookup for GPIO vbus-other failed
[    1.294536] fusb302 4-0022: GPIO lookup for consumer discharge
[    1.294546] fusb302 4-0022: using device tree for GPIO lookup
[    1.294556] of_get_named_gpiod_flags: can't parse 'discharge-gpios' property of node '/i2c@ff3d0000/fusb30x@22[0]'
[    1.294567] of_get_named_gpiod_flags: can't parse 'discharge-gpio' property of node '/i2c@ff3d0000/fusb30x@22[0]'
[    1.294576] fusb302 4-0022: using lookup tables for GPIO lookup
[    1.294586] fusb302 4-0022: lookup for GPIO discharge failed
[    1.294794] fusb302 4-0022: Can't get property of role, set role to default DRP
[    1.304027] fusb302 4-0022: port 0 probe success with role ROLE_MODE_DRP, try_role ROLE_MODE_NONE
[    1.311598] usbcore: registered new interface driver uvcvideo
[    1.312130] USB Video Class driver (1.1.1)
[    1.323011] usbcore: registered new interface driver bfusb
[    1.323622] usbcore: registered new interface driver btusb
[    1.402019] usbcore: registered new interface driver usbhid
[    1.402547] usbhid: USB HID core driver
[    1.406726] usbcore: registered new interface driver snd-usb-audio
[    1.635272] phy phy-ff770000.syscon:usb2-phy@e450.5: Looking up phy-supply from device tree
[    1.635280] phy phy-ff770000.syscon:usb2-phy@e450.5: Looking up phy-supply property in node /syscon@ff770000/usb2-phy@e450/otg-port failed
[    1.635486] phy phy-ff770000.syscon:usb2-phy@e450.5: Looking up vbus-supply from device tree
[    1.635492] phy phy-ff770000.syscon:usb2-phy@e450.5: Looking up vbus-supply property in node /syscon@ff770000/usb2-phy@e450/otg-port failed
[    1.635501] phy phy-ff770000.syscon:usb2-phy@e450.5: Failed to get VBUS supply regulator
[    1.636465] phy phy-ff770000.syscon:usb2-phy@e450.6: Looking up phy-supply from device tree
[    1.636532] vcc5v0_host: could not add device link phy-ff770000.syscon:usb2-phy@e450.6 err -2
[    1.637072] phy phy-ff7c0000.phy.8: Looking up phy-supply property in node /phy@ff7c0000/usb3-port failed
[    2.002312] xhci-hcd xhci-hcd.5.auto: new USB bus registered, assigned bus number 3
[    2.005009] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    2.005732] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.006494] usb usb3: Product: xHCI Host Controller
[    2.007009] usb usb3: Manufacturer: Linux 4.4.132-1075-rockchip-ayufan-ga83beded8524 xhci-hcd
[    2.007904] usb usb3: SerialNumber: xhci-hcd.5.auto
[    2.008827] hub 3-0:1.0: USB hub found
[    2.010665] xhci-hcd xhci-hcd.5.auto: new USB bus registered, assigned bus number 4
[    2.011522] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.012453] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[    2.013164] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.013932] usb usb4: Product: xHCI Host Controller
[    2.014454] usb usb4: Manufacturer: Linux 4.4.132-1075-rockchip-ayufan-ga83beded8524 xhci-hcd
[    2.015351] usb usb4: SerialNumber: xhci-hcd.5.auto
[    2.016257] hub 4-0:1.0: USB hub found
[    2.018942] usb usb4: USB disconnect, device number 1
[    2.044906] xhci-hcd xhci-hcd.5.auto: USB bus 4 deregistered
[    2.046163] usb usb3: USB disconnect, device number 1
[    2.047960] xhci-hcd xhci-hcd.5.auto: USB bus 3 deregistered
[    2.056668] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 3
[    2.059352] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    2.060063] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.060827] usb usb3: Product: xHCI Host Controller
[    2.061348] usb usb3: Manufacturer: Linux 4.4.132-1075-rockchip-ayufan-ga83beded8524 xhci-hcd
[    2.062244] usb usb3: SerialNumber: xhci-hcd.6.auto
[    2.063232] hub 3-0:1.0: USB hub found
[    2.076328] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 4
[    2.086994] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.097798] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[    2.108306] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.114105] usb usb4: Product: xHCI Host Controller
[    2.119391] usb usb4: Manufacturer: Linux 4.4.132-1075-rockchip-ayufan-ga83beded8524 xhci-hcd
[    2.125089] usb usb4: SerialNumber: xhci-hcd.6.auto
[    2.131514] hub 4-0:1.0: USB hub found
[    2.144513] ehci-platform fe380000.usb: EHCI Host Controller
[    2.149510] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 5
[    2.154292] ehci-platform fe380000.usb: irq 27, io mem 0xfe380000
[    2.164358] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
[    2.168907] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[    2.173322] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.177741] usb usb5: Product: EHCI Host Controller
[    2.181911] usb usb5: Manufacturer: Linux 4.4.132-1075-rockchip-ayufan-ga83beded8524 ehci_hcd
[    2.186427] usb usb5: SerialNumber: fe380000.usb
[    2.191426] hub 5-0:1.0: USB hub found
[    2.199780] ohci-platform fe3a0000.usb: Generic Platform OHCI controller
[    2.204285] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 6
[    2.208254] ohci-platform fe3a0000.usb: irq 28, io mem 0xfe3a0000
[    2.266912] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[    2.285507] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.303922] usb usb6: Product: Generic Platform OHCI controller
[    2.322261] usb usb6: Manufacturer: Linux 4.4.132-1075-rockchip-ayufan-ga83beded8524 ohci_hcd
[    2.341046] usb usb6: SerialNumber: fe3a0000.usb
[    2.361476] hub 6-0:1.0: USB hub found
[    2.461390] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[    2.667220] usb 3-1: New USB device found, idVendor=090c, idProduct=1000
[    2.667226] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.667230] usb 3-1: Product: USB Flash Disk
[    2.667234] usb 3-1: Manufacturer: General
[    2.667238] usb 3-1: SerialNumber: 042NR6E8C5MLE2GT
[    2.712883] usb 3-1: ep 0x81 - rounding interval to 128 microframes, ep desc says 255 microframes
[    2.719848] usb 3-1: ep 0x2 - rounding interval to 128 microframes, ep desc says 255 microframes
[    3.080440] usb-storage 3-1:1.0: USB Mass Storage device detected
[    3.081243] scsi host0: usb-storage 3-1:1.0
[    3.081460] usbcore: registered new interface driver usb-storage
[    3.082140] usbcore: registered new interface driver uas
[    4.215095] scsi 0:0:0:0: Direct-Access     General  USB Flash Disk   1100 PQ: 0 ANSI: 4

    Das System läuft. Das Logfile -> https://pastebin.com/FimTdZc3

    Nun wollen wir mal schauen, was der andere Stick so auswirft. Den Corsair Voyager GTX eingesteckt und Los!

    USB3-Stick am USB3-Port

    Log

     =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2018.09.20 09:12:03 =~=~=~=~=~=~=~=~=~=~=~=
 DDR Version 1.13 20180801
 In
 Channel 0: LPDDR4,50MHz
 CS = 0
 MR0=0x98
 MR4=0x3
 MR5=0xFF
 MR8=0x8
 MR12=0x4D
 MR14=0x4D
 MR18=0x0
 MR19=0x0
 MR24=0x8
 MR25=0x0
 CS = 1
 MR0=0x18
 MR4=0x3
 MR5=0xFF
 MR8=0x8
 MR12=0x4D
 MR14=0x4D
 MR18=0x0
 MR19=0x0
 MR24=0x8
 MR25=0x0
 Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB
 Channel 1: LPDDR4,50MHz
 CS = 0
 MR0=0x98
 MR4=0x3
 MR5=0xFF
 MR8=0x8
 MR12=0x4D
 MR14=0x4D
 MR18=0x0
 MR19=0x0
 MR24=0x8
 MR25=0x0
 CS = 1
 MR0=0x18
 MR4=0x1
 MR5=0xFF
 MR8=0x8
 MR12=0x4D
 MR14=0x4D
 MR18=0x0
 MR19=0x0
 MR24=0x8
 MR25=0x0
 Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB
 256B stride
 channel 0
 CS = 0
 MR0=0x98
 MR4=0x81
 MR5=0xFF
 MR8=0x8
 MR12=0x72
 MR14=0x72
 MR18=0x0
 MR19=0x0
 MR24=0x8
 MR25=0x0
 CS = 1
 MR0=0x18
 MR4=0x81
 MR5=0xFF
 MR8=0x8
 MR12=0x72
 MR14=0x72
 MR18=0x0
 MR19=0x0
 MR24=0x8
 MR25=0x0
 channel 1
 CS = 0
 MR0=0x98
 MR4=0x3
 MR5=0xFF
 MR8=0x8
 MR12=0x72
 MR14=0x72
 MR18=0x0
 MR19=0x0
 MR24=0x8
 MR25=0x0
 CS = 1
 MR0=0x18
 MR4=0x1
 MR5=0xFF
 MR8=0x8
 MR12=0x72
 MR14=0x72
 MR18=0x0
 MR19=0x0
 MR24=0x8
 MR25=0x0
 channel 0 training pass!
 channel 1 training pass!
 change freq to 400MHz 0,1
 channel 0
 CS = 0
 MR0=0x98
 MR4=0x1
 MR5=0xFF
 MR8=0x8
 MR12=0x72
 MR14=0x72
 MR18=0x0
 MR19=0x0
 MR24=0x8
 MR25=0x0
 CS = 1
 MR0=0x18
 MR4=0x1
 MR5=0xFF
 MR8=0x8
 MR12=0x72
 MR14=0x72
 MR18=0x0
 MR19=0x0
 MR24=0x8
 MR25=0x0
 channel 1
 CS = 0
 MR0=0x98
 MR4=0x81
 MR5=0xFF
 MR8=0x8
 MR12=0x72
 MR14=0x72
 MR18=0x0
 MR19=0x0
 MR24=0x8
 MR25=0x0
 CS = 1
 MR0=0x18
 MR4=0x1
 MR5=0xFF
 MR8=0x8
 MR12=0x72
 MR14=0x72
 MR18=0x0
 MR19=0x0
 MR24=0x8
 MR25=0x0
 channel 0 training pass!
 channel 1 training pass!
 change freq to 800MHz 1,0
 ch 0 ddrconfig = 0x101, ddrsize = 0x2020
 ch 1 ddrconfig = 0x101, ddrsize = 0x2020
 pmugrf_os_reg[2] = 0x3AA1FAA1, stride = 0xD
 OUT
 U-Boot SPL board init
 
 U-Boot SPL 2017.09-rockchip-ayufan-1033-gdf02018479 (Aug 06 2018 - 22:29:15)
 booted from SPI flash
 Trying to boot from SPI
 NOTICE:  BL31: v1.3(debug):65aa5ce
 NOTICE:  BL31: Built : 10:47:37, Jun 19 2018
 NOTICE:  BL31: Rockchip release version: v1.1
 INFO:    GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
 INFO:    Using opteed sec cpu_context!
 INFO:    boot cpu mask: 0
 INFO:    plat_rockchip_pmu_init(1151): pd status 3e
 INFO:    BL31: Initializing runtime services
 WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
 ERROR:   Error initializing runtime service opteed_fast
 INFO:    BL31: Preparing for EL3 exit to normal world
 INFO:    Entry point address = 0x200000
 INFO:    SPSR = 0x3c9
 
 
 U-Boot 2017.09-rockchip-ayufan-1033-gdf02018479 (Aug 06 2018 - 22:29:23 +0000)
 
 Model: Pine64 RockPro64
 DRAM:  3.9 GiB
 DCDC_REG1@vdd_center: ; enabling
 DCDC_REG2@vdd_cpu_l: ; enabling
 DCDC_REG3@vcc_ddr: ; enabling (ret: -38)
 DCDC_REG4@vcc_1v8: set 1800000 uV; enabling
 LDO_REG1@vcc1v8_dvp: set 1800000 uV; enabling
 LDO_REG2@vcc3v0_touch: set 3000000 uV; enabling
 LDO_REG3@vcc1v8_pmu: set 1800000 uV; enabling
 LDO_REG4@vcc_sd: set 3300000 uV; enabling
 LDO_REG5@vcca3v0_codec: set 3000000 uV; enabling
 LDO_REG6@vcc_1v5: set 1500000 uV; enabling
 LDO_REG7@vcca1v8_codec: set 1800000 uV; enabling
 LDO_REG8@vcc_3v0: set 3000000 uV; enabling
 SWITCH_REG1@vcc3v3_s3: ; enabling (ret: -38)
 SWITCH_REG2@vcc3v3_s0: ; enabling (ret: -38)
 vcc1v8-s0@vcc1v8_s0: set 1800000 uV; enabling (ret: -38)
 dc-12v@dc_12v: set 12000000 uV; enabling (ret: -38)
 vcc-sys@vcc_sys: set 5000000 uV; enabling (ret: -38)
 vcc3v3-sys@vcc3v3_sys: set 3300000 uV; enabling (ret: -38)
 vcc-phy-regulator@vcc_phy: ; enabling (ret: -38)
 vdd-log@vdd_log: ; enabling (ret: -38)
 MMC:   sdhci@fe330000: 0, dwmmc@fe320000: 1
 SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
 *** Warning - bad CRC, using default environment
 
 In:    serial@ff1a0000
 Out:   serial@ff1a0000
 Err:   serial@ff1a0000
 Model: Pine64 RockPro64
 Net:   eth0: ethernet@fe300000
 Hit any key to stop autoboot:  0 
 Card did not respond to voltage select!
 mmc_init: -95, time 20
 Card did not respond to voltage select!
 mmc_init: -95, time 9
 starting USB...
 USB0:   USB EHCI 1.00
 USB1:   USB EHCI 1.00
 USB2:   Register 2000140 NbrPorts 2
 Starting the controller
 USB XHCI 1.10
 USB3:   Register 2000140 NbrPorts 2
 Starting the controller
 USB XHCI 1.10
 scanning bus 0 for devices... 1 USB Device(s) found
 scanning bus 1 for devices... 1 USB Device(s) found
 scanning bus 2 for devices... 1 USB Device(s) found
 scanning bus 3 for devices... 1 USB Device(s) found
        scanning usb for storage devices... 0 Storage Device(s) found
 
 Device 0: unknown device
 Speed: 1000, full duplex
 BOOTP broadcast 1
 BOOTP broadcast 2
 BOOTP broadcast 3
 DHCP client bound to address 192.168.3.15 (1007 ms)
 *** Warning: no boot file name; using 'C0A8030F.img'
 Using ethernet@fe300000 device
 TFTP from server 0.0.0.0; our IP address is 192.168.3.15; sending through gateway 192.168.3.1
 Filename 'C0A8030F.img'.
 Load address: 0x800800
 Loading: *T T

    Es ist alles gleich zum anderen Log. Aber beim Scannen vom USB3-Bus wird der Stick nicht erkannt. Hmm???

    Der selbe Stick am USB2-Port.

    USB3-Stick am USB2-Port

    Logfile

    Link Preview Image
    usb3_stick_usb2_port_ok - Pastebin.com

    Pastebin.com is the number one paste tool since 2002. Pastebin is a website where you can store text online for a set period of time.

    favicon

    Pastebin (pastebin.com)

    dmesg

    rock64@rockpro64v_2_1:~$ sudo dmesg | grep -i usb 
[sudo] password for rock64: 
[    1.796818] usbcore: registered new interface driver usbfs
[    1.797086] usbcore: registered new interface driver hub
[    1.797427] usbcore: registered new device driver usb
[    4.830911] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[    4.831796] usbcore: registered new interface driver pegasus
[    4.832477] usbcore: registered new interface driver rtl8150
[    4.833082] usbcore: registered new interface driver r8152
[    4.833652] usbcore: registered new interface driver asix
[    4.834204] usbcore: registered new interface driver ax88179_178a
[    4.834898] usbcore: registered new interface driver cdc_ether
[    4.835490] usbcore: registered new interface driver dm9601
[    4.836060] usbcore: registered new interface driver CoreChips
[    4.836666] usbcore: registered new interface driver smsc75xx
[    4.837264] usbcore: registered new interface driver smsc95xx
[    4.837838] usbcore: registered new interface driver net1080
[    4.838495] usbcore: registered new interface driver plusb
[    4.839063] usbcore: registered new interface driver cdc_subset
[    4.839665] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[    4.840440] usbcore: registered new interface driver cdc_ncm
[    4.862016] OF: graph: no port node found in /syscon@ff770000/usb2-phy@e450/otg-port
[    4.878662] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.882898] ehci-platform fe380000.usb: EHCI Host Controller
[    4.883450] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 1
[    4.886020] ehci-platform fe380000.usb: irq 30, io mem 0xfe380000
[    4.902423] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
[    4.904589] hub 1-0:1.0: USB hub found
[    4.909185] ehci-platform fe3c0000.usb: EHCI Host Controller
[    4.909739] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 2
[    4.912468] ehci-platform fe3c0000.usb: irq 32, io mem 0xfe3c0000
[    4.926391] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
[    4.928201] hub 2-0:1.0: USB hub found
[    4.931723] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.933894] ohci-platform fe3a0000.usb: Generic Platform OHCI controller
[    4.934653] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 3
[    4.937294] ohci-platform fe3a0000.usb: irq 31, io mem 0xfe3a0000
[    4.999723] hub 3-0:1.0: USB hub found
[    5.001606] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
[    5.002237] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 4
[    5.003822] ohci-platform fe3e0000.usb: irq 33, io mem 0xfe3e0000
[    5.067579] hub 4-0:1.0: USB hub found
[    5.072347] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 5
[    5.079373] hub 5-0:1.0: USB hub found
[    5.081263] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 6
[    5.081968] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0  SuperSpeed
[    5.082776] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[    5.084532] hub 6-0:1.0: USB hub found
[    5.086777] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 7
[    5.164548] hub 7-0:1.0: USB hub found
[    5.188617] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 8
[    5.191985] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0  SuperSpeed
[    5.197829] usb usb8: We don't know the algorithms for LPM for this host, disabling LPM.
[    5.227852] hub 8-0:1.0: USB hub found
[    5.271464] usbcore: registered new interface driver usb-storage
[    5.572499] usbcore: registered new interface driver usbhid
[    5.573102] usbhid: USB HID core driver
[    6.610333] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    6.786867] usbcore: registered new interface driver uas

    lsusb

    rock64@rockpro64v_2_1:~$ lsusb
   Bus 008 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
   Bus 007 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
   Bus 006 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
   Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
   Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
   Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
   Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
   Bus 001 Device 002: ID 1b1c:1a0e Corsair 
   Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

    Ich kann hier leider gar nichts erkennen, wo man auf das Problem schließen kann. Aber evt. hat Kamil ja eine Erklärung dafür. 😞

    Im Fediverse -> @FrankM@nrw.social

    1. NanoPi R5S
    2. Quartz64 Model B, 4GB RAM
    3. Quartz64 Model A, 4GB RAM
    4. RockPro64 v2.1
    0