Skip to content

Mainline Kernel 4.17-rc7

Verschoben Archiv
  • Es ist wahrscheinlich bei Euch nicht anders als bei mir, das man einen möglichst aktuellen Kernel benutzen möchte. Hat wahrscheinlich mit den vielen Sicherheitslücken zu tuen, das man sich einfach sicherer fühlt. Außerdem möchte man ja auch immer die neuesten Features ausprobieren. Gut das Kamil an uns denkt 😉

    Aktuell gibt es dort einen 4.17.0-rc6 Zum Zeitpunkt wo ich das hier tippe, gibt es 4.17-rc7 (vom 27.05.2018). Gut, das kann man noch so eben akzeptieren 🙂 Der Mainline-Kernel soll auf dem ROCKPro64 und dem ROCK64 laufen.

    Ich kann das aktuell nicht testen, da ich den ROCKPro64 eingepackt habe, morgen geht es zum Widerstand ziehen (für die Insider) So bald ich den ROCKPro64 wieder in Betrieb habe, werde ich das ausgiebig testen.

    In der Zwischenzeit was zum Lesen -> https://debian-handbook.info/browse/de-DE/stable/sect.kernel-installation.html

  • Ok, ausprobiert.

    rock64@rockpro64:~$ uname -a
    Linux rockpro64 4.17.0-rc6-1014-ayufan-g5183d4fd6b6a #1 SMP PREEMPT Sun Jun 3 20:54:04 UTC 2018 aarch64 aarch64 aarch64 GNU/Linux
    

    Alle .deb Files runterladen.

    Dann ein

    sudo dpkg -i *.deb
    

    Dann den ROCKPro64 neustarten.

    Sollte der neue Kernel nicht booten oder Probleme machen, kann man den letzten Kernel benutzen. Dazu muss man den U-Boot überwachen

    U-Boot 2017.09-gec1524d (Jun 03 2018 - 14:57:16 +0000), Build: jenkins-linux-build-rock-64-249
    
    
    
    Model: Pine64 RockPro64    
    DRAM:  3.9 GiB    
    MMC:   sdhci@fe330000: 0, dwmmc@fe320000: 1    
    Card did not respond to voltage select!    
    mmc_init: -95, time 21
    
    *** Warning - No block device, using default environment
    
    
    In:    serial@ff1a0000    
    Out:   serial@ff1a0000    
    Err:   serial@ff1a0000    
    Model: Pine64 RockPro64    
    Net:   eth0: ethernet@fe300000    
    Hit any key to stop autoboot:  0
    
    Card did not respond to voltage select!    
    mmc_init: -95, time 21    
    switch to partitions #0, OK    
    mmc1 is current device    
    Scanning mmc 1:6...    
    Found /extlinux/extlinux.conf    
    Retrieving file: /extlinux/extlinux.conf    
    reading /extlinux/extlinux.conf    
    688 bytes read in 3 ms (223.6 KiB/s)
    
    select kernel    
    1:	kernel-latest    
    2:	kernel-previous
    
    Enter choice: 2  
    2:	kernel-previous
    

    Bei select kernel eine "2" eingeben und die Taste "RETURN" betätigen, möglichst zügig 😉 Danach wird der Alte Kernel geladen.

    Leider geht hier auch kein PCIe. USB3 ist bei mir auch extrem lahm. USB3 geht nicht! Also warten....

  • Die CPU Kerne scheinen mit fester Frequenz zu laufen.

    rock64@rockpro64:/usr/local/sbin$ sudo ./armbianmonitor -m
    Stop monitoring using [ctrl]-[c]
    Stop monitoring using [ctrl]-[c]
    Time       big.LITTLE   load %cpu %sys %usr %nice %io %irq   CPU  C.St.
    
    19:54:33: 1800/1416MHz  0.54  15%   0%   0%   0%  14%   0% 44.4°C  0/5
    19:54:39: 1800/1416MHz  0.49   0%   0%   0%   0%   0%   0% 45.6°C  0/5
    19:54:44: 1800/1416MHz  0.45   0%   0%   0%   0%   0%   0% 45.6°C  0/5
    19:54:49: 1800/1416MHz  0.42   0%   0%   0%   0%   0%   0% 45.6°C  0/5
    19:54:54: 1800/1416MHz  0.38   0%   0%   0%   0%   0%   0% 45.6°C  0/5
    19:54:59: 1800/1416MHz  0.35   0%   0%   0%   0%   0%   0% 43.9°C  0/5
    19:55:04: 1800/1416MHz  0.32   0%   0%   0%   0%   0%   0% 45.6°C  0/5
    19:55:09: 1800/1416MHz  0.30   0%   0%   0%   0%   0%   0% 45.6°C  0/5
    

    Dadurch auch eine Stromaufnahme von ca. 4,4 Watt.

    Aber freuen wir uns, das es läuft. Und was mir aufgefallen ist, um Längen stabiler als mit 0.6.50 Zur Erinnerung, der lief hier noch einigermaßen stabil, hatte aber beim Booten so seine Macken. Ab und zu wollte der nicht. Den Mainline habe ich jetzt schon einige Male neugestartet, immer erfolgreich.

    Da kommt mir in den Sinn, liegt es an der Regelung der CPU Kerne, das alle Images so fürchterlich unstabil sind?? Ich kann es nicht beantworten. Kamil kann es evt. 😉

    Update

    (12:57:25) ayufan: if you look at used states, any small spike in CPU usage will bump it to max CPU 🙂

    Damit bringt Armbianmonitor die CPU's immer wieder hoch. OK, dann hätten wir das geklärt. Gefällt mir aber auf 4.4. um Längen besser. Ist aber im Moment auch nicht wichtig. Optimierungen werden sowieso noch lange auf sich warten lassen.

  • HDMI Bildschirmausgabe funktioniert.

    Ein Reboot nicht

    sudo shutdown -r now
    
  • 4.17.0-rc6-1017-ayufan released

    Paar Eindrücke

    • kein Kernel-Panic bei gesteckter PCIe NVMe Karte mit SSD
    • USB3 geht aber mit USB2 Geschwindigkeiten
    • LAN Schnittstelle ist immer noch was langsamer als beim 4.4er Kernel

    LAN

    rock64@rockpro64:/mnt$ iperf3 -c 192.168.3.213
    Connecting to host 192.168.3.213, port 5201
    [  4] local 192.168.3.7 port 41270 connected to 192.168.3.213 port 5201
    [ ID] Interval           Transfer     Bandwidth       Retr  Cwnd
    [  4]   0.00-1.00   sec  99.3 MBytes   833 Mbits/sec    3    310 KBytes       
    [  4]   1.00-2.00   sec  97.7 MBytes   820 Mbits/sec    1    322 KBytes       
    [  4]   2.00-3.00   sec  97.7 MBytes   820 Mbits/sec    0    328 KBytes       
    [  4]   3.00-4.00   sec  97.8 MBytes   820 Mbits/sec    0    338 KBytes       
    [  4]   4.00-5.00   sec  97.7 MBytes   820 Mbits/sec    0    345 KBytes       
    [  4]   5.00-6.00   sec  97.8 MBytes   820 Mbits/sec    0    362 KBytes       
    [  4]   6.00-7.00   sec  97.9 MBytes   822 Mbits/sec    0    404 KBytes       
    [  4]   7.00-8.00   sec  97.8 MBytes   820 Mbits/sec    0    404 KBytes       
    [  4]   8.00-9.00   sec  97.7 MBytes   820 Mbits/sec    0    404 KBytes       
    [  4]   9.00-10.00  sec  97.7 MBytes   820 Mbits/sec    0    404 KBytes       
    - - - - - - - - - - - - - - - - - - - - - - - - -
    [ ID] Interval           Transfer     Bandwidth       Retr
    [  4]   0.00-10.00  sec   979 MBytes   821 Mbits/sec    4             sender
    [  4]   0.00-10.00  sec   977 MBytes   820 Mbits/sec                  receiver
    
    iperf Done.
    rock64@rockpro64:/mnt$ iperf3 -s
    -----------------------------------------------------------
    Server listening on 5201
    -----------------------------------------------------------
    Accepted connection from 192.168.3.213, port 36990
    [  5] local 192.168.3.7 port 5201 connected to 192.168.3.213 port 36992
    [ ID] Interval           Transfer     Bandwidth
    [  5]   0.00-1.00   sec   108 MBytes   908 Mbits/sec                  
    [  5]   1.00-2.00   sec   112 MBytes   938 Mbits/sec                  
    [  5]   2.00-3.00   sec   112 MBytes   942 Mbits/sec                  
    [  5]   3.00-4.00   sec   112 MBytes   941 Mbits/sec                  
    [  5]   4.00-5.00   sec   112 MBytes   941 Mbits/sec                  
    [  5]   5.00-6.00   sec   112 MBytes   941 Mbits/sec                  
    [  5]   6.00-7.00   sec   112 MBytes   941 Mbits/sec                  
    [  5]   7.00-8.00   sec   112 MBytes   942 Mbits/sec                  
    [  5]   8.00-9.00   sec   112 MBytes   941 Mbits/sec                  
    [  5]   9.00-10.00  sec   112 MBytes   941 Mbits/sec                  
    [  5]  10.00-10.03  sec  3.58 MBytes   937 Mbits/sec                  
    - - - - - - - - - - - - - - - - - - - - - - - - -
    [ ID] Interval           Transfer     Bandwidth
    [  5]   0.00-10.03  sec  0.00 Bytes  0.00 bits/sec                  sender
    [  5]   0.00-10.03  sec  1.10 GBytes   938 Mbits/sec                  receiver
    -----------------------------------------------------------
    Server listening on 5201
    -----------------------------------------------------------
    

    USB3

    rock64@rockpro64:/mnt$ sudo dd if=/dev/zero of=sd.img bs=1M count=4096 conv=fdatasync
    4096+0 records in
    4096+0 records out
    4294967296 bytes (4.3 GB, 4.0 GiB) copied, 145.552 s, 29.5 MB/s
    

    dmesg

    [ 9397.455487] alloc_contig_range: [f711d, f711e) PFNs busy
    [ 9397.455767] alloc_contig_range: [f7122, f7123) PFNs busy
    [ 9397.456041] alloc_contig_range: [f7123, f7124) PFNs busy
    [ 9397.456308] alloc_contig_range: [f7124, f7125) PFNs busy
    [ 9397.456577] alloc_contig_range: [f7125, f7126) PFNs busy
    [ 9397.456849] alloc_contig_range: [f7126, f7127) PFNs busy
    [ 9397.457119] alloc_contig_range: [f7127, f7128) PFNs busy
    [ 9397.457382] alloc_contig_range: [f7128, f7129) PFNs busy
    [ 9397.458157] alloc_contig_range: [f711d, f711e) PFNs busy
    [ 9397.458429] alloc_contig_range: [f7122, f7123) PFNs busy
    [ 9397.599156] usb 7-1: new high-speed USB device number 2 using xhci-hcd
    [ 9397.827180] scsi host0: uas
    [ 9397.847260] scsi 0:0:0:0: Direct-Access     SanDisk  SDSSDA240G       Z320 PQ: 0 ANSI: 6
    [ 9397.848537] usbcore: registered new interface driver uas
    [ 9397.849422] sd 0:0:0:0: [sda] 468862128 512-byte logical blocks: (240 GB/224 GiB)
    [ 9397.849582] sd 0:0:0:0: [sda] Write Protect is off
    [ 9397.849587] sd 0:0:0:0: [sda] Mode Sense: 2f 00 00 00
    [ 9397.849890] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 9397.853951]  sda: sda1
    [ 9397.856234] sd 0:0:0:0: [sda] Attached SCSI disk
    [ 9430.835974] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
    
  • 4.17.0-rc6-1019-ayufan released

    Was ist mir aufgefallen

    • PCIe arbeitet jetzt mit 5GT/s
    • USB3 geht bei mir nicht mehr, keine Ahnung warum!?!?!?
  • Tja, wenn das Bootproblem nicht wäre, könnte man mit dem Mainline schon leben.

    rock64@rockpro64:/$ uname -a
    Linux rockpro64 4.17.0-rc6-1019-ayufan-gfafc3e1c913f #1 SMP PREEMPT Tue Jun 12 19:06:59 UTC 2018 aarch64 aarch64 aarch64 GNU/Linux
    

    Mal meine Standardinstallation mit nodejs, redis-server und NodeBB drauf gehauen. Das läuft schon richtig rund.

    • Angschlossen sind ein Monitor mittels HDMI - einwandfrei
    • Am USB3-Port ein Keyboard - ok
    • Die NVMe Karte mit SSD ist drin - ok
    • 6 Kerne werden erkannt

    0_1529149482212_hdmi_htop_ergebnis.jpg

    was noch nicht so richtig funktioniert

    • ich kann am USB3 keine HDD/SDD mehr erkennen, drei verschieden Adapter. Keiner geht!
    • Soundkarte nicht gefunden
    • Booten ist Zufall, Reboot geht nicht.

    So weit macht das schon einen sehr guten Eindruck, für diesen frühen Zeitpunkt. Was nervt ist das Bootproblem, das nervt so richtig wenn man testen will und man nie weiß ob das SOC jetzt mal möchte 🙂

    rock64@rockpro64:/$ uptime
     11:41:12 up  5:11,  2 users,  load average: 0.00, 0.00, 0.00
    
  • 4.17.0-rc6-1029-ayufan released

    Seit 1021 funktioniert USB3.

  • [V] ROCKPro64 incl. PCIe SATA-Karte

    Verschoben Archiv
    2
    0 Stimmen
    2 Beiträge
    207 Aufrufe
    FrankMF

    Verkauft!

  • ROCKPro64 - USB3

    ROCKPro64
    1
    0 Stimmen
    1 Beiträge
    263 Aufrufe
    Niemand hat geantwortet
  • Booten von USB3

    Verschoben ROCKPro64
    1
    0 Stimmen
    1 Beiträge
    286 Aufrufe
    Niemand hat geantwortet
  • Der 3. ROCKPro64

    ROCKPro64
    3
    0 Stimmen
    3 Beiträge
    911 Aufrufe
    FrankMF

    Nachdem ich jetzt mein NAS neu gemacht habe, schauen wir mal, was die Chinesen geliefert haben. Bestellt hatte ich

    ROCKPro64 v2.1 2GB RAM Kühlkörper Netzteil 3A USB-Adapter für eMMC-Modul

    Endlich habe ich mal an den USB-Adapter für das eMMC-Modul gedacht 🙂

    0_1540029624802_IMG_20181020_115348_ergebnis.jpg

    Was ist mir aufgefallen? Das Versionsdatum ist neu (siehe oben) Die PCIe NVMe Karte ist neu

    Bei der PCIe NVMe Karte liegt eine Abstandshülse aus Messing und eine winzig kleine Schraube bei. Damit bekomme ich aber nicht die NVMe-SSD befestigt. Ich habe dann gemurkst 😉 Da sollte Pine64 unbedingt nachbessern!

    So sieht das dann zusammengebaut aus.

    0_1540029756582_IMG_20181020_115425_ergebnis.jpg

    0_1540029767082_IMG_20181020_115438_ergebnis.jpg

    Da ich ein paarmal gelesen hatte, das Leute Probleme mit dem PCIe NVMe Adapter hatten, direkt als erstes mal ein Test ob das reibungslos funktioniert.

    Sys rock64@rockpro64:/mnt$ uname -a Linux rockpro64 4.4.132-1075-rockchip-ayufan-ga83beded8524 #1 SMP Thu Jul 26 08:22:22 UTC 2018 aarch64 aarch64 aarch64 GNU/Linux lspci rock64@rockpro64:/mnt$ sudo lspci -vvv [sudo] password for rock64: 00:00.0 PCI bridge: Rockchip Inc. RK3399 PCI Express Root Port Device 0100 (prog-if 00 [Normal decode]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort+ <MAbort+ >SERR+ <PERR+ INTx- Latency: 0 Interrupt: pin A routed to IRQ 238 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00000000-00000fff Memory behind bridge: fa000000-fa0fffff Prefetchable memory behind bridge: 00000000-000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [80] Power Management version 3 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME+ Capabilities: [90] MSI: Enable+ Count=1/1 Maskable+ 64bit+ Address: 00000000fee30040 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [b0] MSI-X: Enable- Count=1 Masked- Vector table: BAR=0 offset=00000000 PBA: BAR=0 offset=00000008 Capabilities: [c0] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0 ExtTag- RBE+ DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L1, Exit Latency L0s <256ns, L1 <8us ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+ LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt+ AutBWInt+ LnkSta: Speed 5GT/s, Width x4, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #0, PowerLimit 0.000W; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Off, PwrInd Off, Power+ Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL+ CmdCplt- PresDet- Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR+, OBFF Via message ARIFwd+ DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [100 v2] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Capabilities: [274 v1] Transaction Processing Hints Interrupt vector mode supported Device specific mode supported Steering table in TPH capability structure Kernel driver in use: pcieport 01:00.0 Non-Volatile memory controller: Samsung Electronics Co Ltd NVMe SSD Controller SM961/PM961 (prog-if 02 [NVM Express]) Subsystem: Samsung Electronics Co Ltd NVMe SSD Controller SM961/PM961 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 237 Region 0: Memory at fa000000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/32 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [70] Express (v2) Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ SlotPowerLimit 0.000W DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 8GT/s, Width x4, ASPM L1, Exit Latency L0s unlimited, L1 <64us ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+ LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk- ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- LnkSta: Speed 5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR+, OBFF Not Supported DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [b0] MSI-X: Enable+ Count=8 Masked- Vector table: BAR=0 offset=00003000 PBA: BAR=0 offset=00002000 Capabilities: [100 v2] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Capabilities: [148 v1] Device Serial Number 00-00-00-00-00-00-00-00 Capabilities: [158 v1] Power Budgeting <?> Capabilities: [168 v1] #19 Capabilities: [188 v1] Latency Tolerance Reporting Max snoop latency: 0ns Max no snoop latency: 0ns Capabilities: [190 v1] L1 PM Substates L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+ PortCommonModeRestoreTime=10us PortTPowerOnTime=10us L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1- T_CommonMode=0us LTR1.2_Threshold=0ns L1SubCtl2: T_PwrOn=10us Kernel driver in use: nvme

    Da sieht alles gut aus. x4 alles Bestens!

    iozone rock64@rockpro64:/mnt$ sudo iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Iozone: Performance Test of File I/O Version $Revision: 3.429 $ Compiled for 64 bit mode. Build: linux Contributors:William Norcott, Don Capps, Isom Crawford, Kirby Collins Al Slater, Scott Rhine, Mike Wisner, Ken Goss Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR, Randy Dunlap, Mark Montague, Dan Million, Gavin Brebner, Jean-Marc Zucconi, Jeff Blomberg, Benny Halevy, Dave Boone, Erik Habbinga, Kris Strecker, Walter Wong, Joshua Root, Fabrice Bacchella, Zhenghua Xue, Qin Li, Darren Sawyer, Vangel Bojaxhi, Ben England, Vikentsi Lapa. Run began: Sat Oct 20 10:08:28 2018 Include fsync in write timing O_DIRECT feature enabled Auto Mode File size set to 102400 kB Record Size 4 kB Record Size 16 kB Record Size 512 kB Record Size 1024 kB Record Size 16384 kB Command line used: iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Output is in kBytes/sec Time Resolution = 0.000001 seconds. Processor cache size set to 1024 kBytes. Processor cache line size set to 32 bytes. File stride size set to 17 * record size. random random bkwd record stride kB reclen write rewrite read reread read write read rewrite read fwrite frewrite fread freread 102400 4 63896 108269 91858 95309 32845 73173 102400 16 123393 236653 273766 275807 118450 199130 102400 512 471775 570571 484612 496942 441345 575817 102400 1024 544229 642558 508895 511834 486506 647765 102400 16384 1044520 1100322 1069825 1092146 1089301 1086757 iozone test complete.

    Das sieht nicht optimal aus, schau ich mir später an. Das hier soll nur ein kurzer Test sein ob das Board rennt 🙂

    Nachdem ich mittlerweile zwei ROCKPro64 im "produktiven" Einsatz habe, war es immer sehr mühsam mal eben was zu testen. Man will die anderen ja nicht immer ausmachen, dran rumhantieren usw. Deswegen jetzt der dritte, der im Moment dann die Rolle des Testkandidaten einnimmt. Ab sofort kann ich wieder nach Lust und Laune, neue Images testen usw.

  • Kernel 4.4.x

    Angeheftet Images
    45
    0 Stimmen
    45 Beiträge
    4k Aufrufe
    FrankMF

    4.4.202-1237-rockchip-ayufan released

    PATCH: kernel 4.4.201-202
  • 960 EVO M.2 vs. 970 PRO M.2

    ROCKPro64
    2
    0 Stimmen
    2 Beiträge
    2k Aufrufe
    FrankMF

    Die 970 steckt jetzt in meinem Haupt-PC. Dort werkelt ein aktuelles Linux Mint Cinnamon 19. Zum Vergleich.

    100M frank@frank-MS-7A34:~$ sudo iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 [sudo] Passwort für frank: Iozone: Performance Test of File I/O Version $Revision: 3.429 $ Compiled for 64 bit mode. Build: linux-AMD64 Contributors:William Norcott, Don Capps, Isom Crawford, Kirby Collins Al Slater, Scott Rhine, Mike Wisner, Ken Goss Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR, Randy Dunlap, Mark Montague, Dan Million, Gavin Brebner, Jean-Marc Zucconi, Jeff Blomberg, Benny Halevy, Dave Boone, Erik Habbinga, Kris Strecker, Walter Wong, Joshua Root, Fabrice Bacchella, Zhenghua Xue, Qin Li, Darren Sawyer, Vangel Bojaxhi, Ben England, Vikentsi Lapa. Run began: Sun Aug 19 16:52:19 2018 Include fsync in write timing O_DIRECT feature enabled Auto Mode File size set to 102400 kB Record Size 4 kB Record Size 16 kB Record Size 512 kB Record Size 1024 kB Record Size 16384 kB Command line used: iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Output is in kBytes/sec Time Resolution = 0.000001 seconds. Processor cache size set to 1024 kBytes. Processor cache line size set to 32 bytes. File stride size set to 17 * record size. random random bkwd record stride kB reclen write rewrite read reread read write read rewrite read fwrite frewrite fread freread 102400 4 92640 121912 131074 139525 45719 116653 102400 16 254286 285267 285539 320370 108049 314486 102400 512 537947 581765 606103 598137 537701 588214 102400 1024 566892 547921 567369 597286 518014 558686 102400 16384 1407884 1642148 1941120 2115608 2006947 1668118 iozone test complete. 1000M frank@frank-MS-7A34:~$ sudo iozone -e -I -a -s 1000M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Iozone: Performance Test of File I/O Version $Revision: 3.429 $ Compiled for 64 bit mode. Build: linux-AMD64 Contributors:William Norcott, Don Capps, Isom Crawford, Kirby Collins Al Slater, Scott Rhine, Mike Wisner, Ken Goss Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR, Randy Dunlap, Mark Montague, Dan Million, Gavin Brebner, Jean-Marc Zucconi, Jeff Blomberg, Benny Halevy, Dave Boone, Erik Habbinga, Kris Strecker, Walter Wong, Joshua Root, Fabrice Bacchella, Zhenghua Xue, Qin Li, Darren Sawyer, Vangel Bojaxhi, Ben England, Vikentsi Lapa. Run began: Sun Aug 19 15:28:38 2018 Include fsync in write timing O_DIRECT feature enabled Auto Mode File size set to 1024000 kB Record Size 4 kB Record Size 16 kB Record Size 512 kB Record Size 1024 kB Record Size 16384 kB Command line used: iozone -e -I -a -s 1000M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Output is in kBytes/sec Time Resolution = 0.000001 seconds. Processor cache size set to 1024 kBytes. Processor cache line size set to 32 bytes. File stride size set to 17 * record size. random random bkwd record stride kB reclen write rewrite read reread read write read rewrite read fwrite frewrite fread freread 1024000 4 95635 121379 108328 108265 45369 123356 1024000 16 239238 314359 245937 241877 105865 297193 1024000 512 596812 620661 442100 382367 351948 613525 1024000 1024 608903 611898 434687 417192 412018 646465 1024000 16384 1898738 2004622 2143647 2188062 2099674 1983240 iozone test complete.

    Da scheint auf dem ROCKPro64 noch ein wenig Luft nach oben.

  • u-boot-flash-spi-rockpro64.img.xz

    Verschoben Tools
    1
    0 Stimmen
    1 Beiträge
    1k Aufrufe
    Niemand hat geantwortet
  • ROCKPro64 Forum

    ROCKPro64
    1
    0 Stimmen
    1 Beiträge
    648 Aufrufe
    Niemand hat geantwortet