linux-nerds.org

Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you have been placed in read-only mode.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

ROCKPro64 - USB-C -> LAN

ROCKPro64

1 Beiträge 1 Kommentatoren 312 Aufrufe

FrankM

schrieb am

Mal einen USB-C to WLan Adapter besorgt und am ROCKPro64 ausprobiert.

Den Adapter eingesteckt, Netzwerkkabel angeschlossen und nachgeschaut ob er erkannt wird.

[63435.162398] usb 8-1: new SuperSpeed USB device number 2 using xhci-hcd
[63435.185715] usb 8-1: New USB device found, idVendor=0bda, idProduct=8153
[63435.185744] usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[63435.185764] usb 8-1: Product: USB 10/100/1000 LAN
[63435.185781] usb 8-1: Manufacturer: Realtek
[63435.185796] usb 8-1: SerialNumber: 00026C
[63435.256051] usbcore: registered new interface driver r8152
[63435.410987] usb 8-1: reset SuperSpeed USB device number 2 using xhci-hcd
[63435.493485] r8152 8-1:1.0 eth1: v1.08.3
[63435.502207] r8152 8-1:1.0 enx00e04c68026f: renamed from eth1

Ok, schön

rock64@rockpro64:~$ ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UNKNOWN group default qlen 1000
    link/ether 62:03:b0:d6:dc:b3 brd ff:ff:ff:ff:ff:ff
    inet 192.168.3.17/24 brd 192.168.3.255 scope global dynamic eth0
       valid_lft 2976sec preferred_lft 2976sec
    inet6 fe80::6003:b0ff:fed6:dcb3/64 scope link 
       valid_lft forever preferred_lft forever
3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state DORMANT group default qlen 1000
    link/ether ac:83:f3:e6:1f:b2 brd ff:ff:ff:ff:ff:ff
4: enx00e04c68026f: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether 00:e0:4c:68:02:6f brd ff:ff:ff:ff:ff:ff

Unten sieht man die Schnittstelle enx00e04c68026f Ok, Schnittstelle ist nicht konfiguriert. Ab ins Verzeichnis /etc/netplan Dort legen wir eine Datei mit dem Namen enx00e04c68026f.yaml an. Inhalt:

network:
  version: 2
  renderer: networkd
  ethernets:
    enx00e04c68026f:
      dhcp4: true

Nix besonderes, einfach per DHCP eine IP-Adresse besorgen. Dann

sudo netplan try

Und schwupps, ist die IP-Adresse da.

rock64@rockpro64:/etc/netplan$ ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UNKNOWN group default qlen 1000
    link/ether 62:03:b0:d6:dc:b3 brd ff:ff:ff:ff:ff:ff
    inet 192.168.3.17/24 brd 192.168.3.255 scope global dynamic eth0
       valid_lft 1912sec preferred_lft 1912sec
    inet6 fe80::6003:b0ff:fed6:dcb3/64 scope link 
       valid_lft forever preferred_lft forever
3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state DORMANT group default qlen 1000
    link/ether ac:83:f3:e6:1f:b2 brd ff:ff:ff:ff:ff:ff
4: enx00e04c68026f: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
    link/ether 00:e0:4c:68:02:6f brd ff:ff:ff:ff:ff:ff
    inet 192.168.3.16/24 brd 192.168.3.255 scope global dynamic enx00e04c68026f
       valid_lft 1959sec preferred_lft 1959sec
    inet6 fe80::2e0:4cff:fe68:26f/64 scope link 
       valid_lft forever preferred_lft forever

iperf3

Kurz die Geschwindigkeit testen, Gegenstelle war mein haupt-PC.

rock64@rockpro64:/etc/netplan$ sudo iperf3 -s
-----------------------------------------------------------
Server listening on 5201
-----------------------------------------------------------
Accepted connection from 192.168.3.213, port 60662
[  5] local 192.168.3.16 port 5201 connected to 192.168.3.213 port 60664
[ ID] Interval           Transfer     Bandwidth
[  5]   0.00-1.00   sec   108 MBytes   909 Mbits/sec                  
[  5]   1.00-2.00   sec   112 MBytes   941 Mbits/sec                  
[  5]   2.00-3.00   sec   112 MBytes   941 Mbits/sec                  
[  5]   3.00-4.00   sec   112 MBytes   941 Mbits/sec                  
[  5]   4.00-5.00   sec   112 MBytes   941 Mbits/sec                  
[  5]   5.00-6.00   sec   112 MBytes   941 Mbits/sec                  
[  5]   6.00-7.00   sec   112 MBytes   941 Mbits/sec                  
[  5]   7.00-8.00   sec   112 MBytes   941 Mbits/sec                  
[  5]   8.00-9.00   sec   112 MBytes   941 Mbits/sec                  
[  5]   9.00-10.00  sec   112 MBytes   942 Mbits/sec                  
[  5]  10.00-10.02  sec  2.09 MBytes   935 Mbits/sec                  
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bandwidth
[  5]   0.00-10.02  sec  0.00 Bytes  0.00 bits/sec                  sender
[  5]   0.00-10.02  sec  1.09 GBytes   938 Mbits/sec                  receiver
-----------------------------------------------------------
Server listening on 5201
-----------------------------------------------------------
Accepted connection from 192.168.3.213, port 60666
[  5] local 192.168.3.16 port 5201 connected to 192.168.3.213 port 60668
[ ID] Interval           Transfer     Bandwidth       Retr  Cwnd
[  5]   0.00-1.00   sec   114 MBytes   952 Mbits/sec    0    892 KBytes       
[  5]   1.00-2.00   sec   112 MBytes   943 Mbits/sec    0    892 KBytes       
[  5]   2.00-3.00   sec   112 MBytes   941 Mbits/sec    0    892 KBytes       
[  5]   3.00-4.00   sec   111 MBytes   936 Mbits/sec    0    892 KBytes       
[  5]   4.00-5.00   sec   112 MBytes   944 Mbits/sec    0    892 KBytes       
[  5]   5.00-6.00   sec   112 MBytes   944 Mbits/sec    0    892 KBytes       
[  5]   6.00-7.00   sec   112 MBytes   941 Mbits/sec    0    892 KBytes       
[  5]   7.00-8.00   sec   111 MBytes   936 Mbits/sec    0    949 KBytes       
[  5]   8.00-9.00   sec   112 MBytes   942 Mbits/sec    0   1.90 MBytes       
[  5]   9.00-10.00  sec   111 MBytes   935 Mbits/sec    0   1.90 MBytes       
[  5]  10.00-10.02  sec  2.50 MBytes  1.26 Gbits/sec    0   1.90 MBytes       
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bandwidth       Retr
[  5]   0.00-10.02  sec  1.10 GBytes   942 Mbits/sec    0             sender
[  5]   0.00-10.02  sec  0.00 Bytes  0.00 bits/sec                  receiver
-----------------------------------------------------------
Server listening on 5201
-----------------------------------------------------------

Fazit

Adapter funktioniert ohne Probleme, mit vollem Tempo

Anmelden zum Antworten

F

Mainline 5.13.x
Beobachtet Ignoriert Geplant Angeheftet Gesperrt Verschoben Images linux rockpro64
1

0 Stimmen

1 Beiträge

210 Aufrufe

Niemand hat geantwortet
F

ROCKPro64 - PCIe SATA-Karte macht immer mal Probleme
Beobachtet Ignoriert Geplant Angeheftet Gesperrt Verschoben ROCKPro64 rockpro64
2

0 Stimmen

2 Beiträge

526 Aufrufe

F

Das ist das Ergebnis des Stresstests [ 2461.489468] ata2.00: exception Emask 0x10 SAct 0xffffffff SErr 0x400000 action 0x6 frozen [ 2461.490206] ata2.00: irq_stat 0x08000000, interface fatal error [ 2461.490732] ata2: SError: { Handshk } [ 2461.491062] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.491532] ata2.00: cmd 61/40:00:f8:a6:64/05:00:84:00:00/40 tag 0 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.492993] ata2.00: status: { DRDY } [ 2461.493327] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.493796] ata2.00: cmd 61/c0:08:38:ac:64/03:00:84:00:00/40 tag 1 ncq dma 491520 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.495181] ata2.00: status: { DRDY } [ 2461.495507] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.496276] ata2.00: cmd 61/c0:10:a0:f5:64/02:00:84:00:00/40 tag 2 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.497697] ata2.00: status: { DRDY } [ 2461.498029] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.498497] ata2.00: cmd 61/40:18:60:f8:64/05:00:84:00:00/40 tag 3 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.499886] ata2.00: status: { DRDY } [ 2461.500213] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.500681] ata2.00: cmd 61/c0:20:a0:fd:64/02:00:84:00:00/40 tag 4 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.502087] ata2.00: status: { DRDY } [ 2461.502416] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.502884] ata2.00: cmd 61/40:28:60:00:65/05:00:84:00:00/40 tag 5 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.505026] ata2.00: status: { DRDY } [ 2461.505378] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.505852] ata2.00: cmd 61/c0:30:a0:05:65/02:00:84:00:00/40 tag 6 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.507244] ata2.00: status: { DRDY } [ 2461.507572] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.508040] ata2.00: cmd 61/40:38:60:08:65/05:00:84:00:00/40 tag 7 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.509472] ata2.00: status: { DRDY } [ 2461.509808] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.510277] ata2.00: cmd 61/a0:40:a0:0d:65/02:00:84:00:00/40 tag 8 ncq dma 344064 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.511667] ata2.00: status: { DRDY } [ 2461.511994] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.512461] ata2.00: cmd 61/40:48:00:20:66/05:00:84:00:00/40 tag 9 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.514503] ata2.00: status: { DRDY } [ 2461.514850] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.515322] ata2.00: cmd 61/40:50:00:28:66/05:00:84:00:00/40 tag 10 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.516721] ata2.00: status: { DRDY } [ 2461.517084] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.517562] ata2.00: cmd 61/c0:58:40:2d:66/02:00:84:00:00/40 tag 11 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.519253] ata2.00: status: { DRDY } [ 2461.519595] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.520066] ata2.00: cmd 61/40:60:f8:9e:64/05:00:84:00:00/40 tag 12 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.521504] ata2.00: status: { DRDY } [ 2461.521840] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.522309] ata2.00: cmd 61/c0:68:38:a4:64/02:00:84:00:00/40 tag 13 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.523706] ata2.00: status: { DRDY } [ 2461.524033] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.524501] ata2.00: cmd 61/40:70:f8:af:64/05:00:84:00:00/40 tag 14 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.525925] ata2.00: status: { DRDY } [ 2461.526256] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.526725] ata2.00: cmd 61/c0:78:38:b5:64/02:00:84:00:00/40 tag 15 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.528122] ata2.00: status: { DRDY } [ 2461.528449] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.528939] ata2.00: cmd 61/40:80:f8:b7:64/05:00:84:00:00/40 tag 16 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.530339] ata2.00: status: { DRDY } [ 2461.530667] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.531136] ata2.00: cmd 61/c0:88:38:bd:64/02:00:84:00:00/40 tag 17 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.532532] ata2.00: status: { DRDY } [ 2461.532880] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.533357] ata2.00: cmd 61/40:90:f8:bf:64/05:00:84:00:00/40 tag 18 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.534754] ata2.00: status: { DRDY } [ 2461.535081] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.535549] ata2.00: cmd 61/c0:98:38:c5:64/02:00:84:00:00/40 tag 19 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.536970] ata2.00: status: { DRDY } [ 2461.537301] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.537769] ata2.00: cmd 61/40:a0:f8:c7:64/05:00:84:00:00/40 tag 20 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.539165] ata2.00: status: { DRDY } [ 2461.539491] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.539960] ata2.00: cmd 61/c0:a8:38:cd:64/02:00:84:00:00/40 tag 21 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.541381] ata2.00: status: { DRDY } [ 2461.541713] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.542182] ata2.00: cmd 61/40:b0:f8:cf:64/05:00:84:00:00/40 tag 22 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.543577] ata2.00: status: { DRDY } [ 2461.543905] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.544374] ata2.00: cmd 61/40:b8:f8:d7:64/05:00:84:00:00/40 tag 23 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.545790] ata2.00: status: { DRDY } [ 2461.546120] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.546589] ata2.00: cmd 61/c0:c0:38:dd:64/02:00:84:00:00/40 tag 24 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.547987] ata2.00: status: { DRDY } [ 2461.548314] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.548782] ata2.00: cmd 61/a8:c8:f8:df:64/05:00:84:00:00/40 tag 25 ncq dma 741376 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.550198] ata2.00: status: { DRDY } [ 2461.550530] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.550999] ata2.00: cmd 61/c0:d0:a0:e5:64/02:00:84:00:00/40 tag 26 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.552396] ata2.00: status: { DRDY } [ 2461.552723] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.553208] ata2.00: cmd 61/40:d8:60:e8:64/05:00:84:00:00/40 tag 27 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.554607] ata2.00: status: { DRDY } [ 2461.554935] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.555404] ata2.00: cmd 61/c0:e0:a0:ed:64/02:00:84:00:00/40 tag 28 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.556800] ata2.00: status: { DRDY } [ 2461.557145] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.557617] ata2.00: cmd 61/40:e8:60:f0:64/05:00:84:00:00/40 tag 29 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.559012] ata2.00: status: { DRDY } [ 2461.559340] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.559807] ata2.00: cmd 61/c0:f0:38:d5:64/02:00:84:00:00/40 tag 30 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.561221] ata2.00: status: { DRDY } [ 2461.561552] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.562021] ata2.00: cmd 61/c0:f8:40:25:66/02:00:84:00:00/40 tag 31 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.563416] ata2.00: status: { DRDY } [ 2461.563752] ata2: hard resetting link [ 2471.561504] ata2: softreset failed (1st FIS failed) [ 2471.561959] ata2: hard resetting link [ 2481.560785] ata2: softreset failed (1st FIS failed) [ 2481.561238] ata2: hard resetting link [ 2516.561654] ata2: softreset failed (1st FIS failed) [ 2516.562109] ata2: limiting SATA link speed to 3.0 Gbps [ 2516.562113] ata2: hard resetting link [ 2521.561261] ata2: softreset failed (1st FIS failed) [ 2521.561715] ata2: reset failed, giving up [ 2521.562074] ata2.00: disabled [ 2521.562575] ata2: EH complete [ 2521.562677] sd 1:0:0:0: [sdb] tag#18 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.562686] sd 1:0:0:0: [sdb] tag#18 CDB: opcode=0x35 35 00 00 00 00 00 00 00 00 00 [ 2521.562701] print_req_error: I/O error, dev sdb, sector 0 [ 2521.562791] sd 1:0:0:0: [sdb] tag#20 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.562802] sd 1:0:0:0: [sdb] tag#19 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.562873] sd 1:0:0:0: [sdb] tag#19 CDB: opcode=0x2a 2a 00 84 66 25 40 00 02 c0 00 [ 2521.562888] print_req_error: I/O error, dev sdb, sector 2221286720 [ 2521.563107] sd 1:0:0:0: [sdb] tag#21 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.563126] sd 1:0:0:0: [sdb] tag#21 CDB: opcode=0x2a 2a 00 84 64 f0 60 00 05 40 00 [ 2521.563138] print_req_error: I/O error, dev sdb, sector 2221207648 [ 2521.563422] sd 1:0:0:0: [sdb] tag#22 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.563772] sd 1:0:0:0: [sdb] tag#20 CDB: opcode=0x2a 2a 00 84 64 d5 38 00 02 c0 00 [ 2521.564326] print_req_error: I/O error, dev sdb, sector 2221200696 [ 2521.564337] sd 1:0:0:0: [sdb] tag#22 CDB: opcode=0x2a 2a 00 84 64 ed a0 00 02 c0 00 [ 2521.564896] print_req_error: I/O error, dev sdb, sector 2221206944 [ 2521.565088] sd 1:0:0:0: [sdb] tag#26 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.565469] sd 1:0:0:0: [sdb] tag#26 CDB: opcode=0x2a 2a 00 84 64 dd 38 00 02 c0 00 [ 2521.565483] print_req_error: I/O error, dev sdb, sector 2221202744 [ 2521.565610] sd 1:0:0:0: [sdb] tag#23 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.566056] sd 1:0:0:0: [sdb] tag#23 CDB: opcode=0x2a 2a 00 84 64 e8 60 00 05 40 00 [ 2521.566069] print_req_error: I/O error, dev sdb, sector 2221205600 [ 2521.566183] sd 1:0:0:0: [sdb] tag#29 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.566641] sd 1:0:0:0: [sdb] tag#29 CDB: opcode=0x2a 2a 00 84 64 cd 38 00 02 c0 00 [ 2521.566654] print_req_error: I/O error, dev sdb, sector 2221198648 [ 2521.566954] sd 1:0:0:0: [sdb] tag#24 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.567224] sd 1:0:0:0: [sdb] tag#24 CDB: opcode=0x2a 2a 00 84 64 e5 a0 00 02 c0 00 [ 2521.567237] print_req_error: I/O error, dev sdb, sector 2221204896 [ 2521.567459] sd 1:0:0:0: [sdb] tag#30 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.567809] sd 1:0:0:0: [sdb] tag#30 CDB: opcode=0x2a 2a 00 84 64 c7 f8 00 05 40 00 [ 2521.567821] print_req_error: I/O error, dev sdb, sector 2221197304 [ 2521.584903] md: super_written gets error=10 [ 2521.585306] md/raid1:md0: Disk failure on dm-1, disabling device. md/raid1:md0: Operation continuing on 1 devices. [ 2526.581450] scsi_io_completion_action: 41779 callbacks suppressed [ 2526.581461] sd 1:0:0:0: [sdb] tag#27 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.581467] sd 1:0:0:0: [sdb] tag#27 CDB: opcode=0x2a 2a 00 84 66 7d 50 00 00 01 00 [ 2526.581469] print_req_error: 41780 callbacks suppressed [ 2526.581471] print_req_error: I/O error, dev sdb, sector 2221309264 [ 2526.582524] sd 1:0:0:0: [sdb] tag#28 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.582530] sd 1:0:0:0: [sdb] tag#28 CDB: opcode=0x2a 2a 00 84 66 7d 51 00 00 01 00 [ 2526.582534] print_req_error: I/O error, dev sdb, sector 2221309265 [ 2526.583366] sd 1:0:0:0: [sdb] tag#29 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.583370] sd 1:0:0:0: [sdb] tag#29 CDB: opcode=0x2a 2a 00 84 66 7d 52 00 00 01 00 [ 2526.583373] print_req_error: I/O error, dev sdb, sector 2221309266 [ 2526.584113] sd 1:0:0:0: [sdb] tag#30 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.584117] sd 1:0:0:0: [sdb] tag#30 CDB: opcode=0x2a 2a 00 84 66 7d 53 00 00 01 00 [ 2526.584119] print_req_error: I/O error, dev sdb, sector 2221309267 [ 2526.584960] sd 1:0:0:0: [sdb] tag#0 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.584968] sd 1:0:0:0: [sdb] tag#0 CDB: opcode=0x2a 2a 00 84 66 7d 54 00 00 01 00 [ 2526.584971] print_req_error: I/O error, dev sdb, sector 2221309268 [ 2526.585765] sd 1:0:0:0: [sdb] tag#1 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.585769] sd 1:0:0:0: [sdb] tag#1 CDB: opcode=0x2a 2a 00 84 66 7d 55 00 00 01 00 [ 2526.585772] print_req_error: I/O error, dev sdb, sector 2221309269 [ 2526.586461] sd 1:0:0:0: [sdb] tag#2 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.586465] sd 1:0:0:0: [sdb] tag#2 CDB: opcode=0x2a 2a 00 84 66 7d 56 00 00 01 00 [ 2526.586468] print_req_error: I/O error, dev sdb, sector 2221309270 [ 2526.587144] sd 1:0:0:0: [sdb] tag#3 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.587148] sd 1:0:0:0: [sdb] tag#3 CDB: opcode=0x2a 2a 00 84 66 7d 57 00 00 01 00 [ 2526.587150] print_req_error: I/O error, dev sdb, sector 2221309271 [ 2526.587734] sd 1:0:0:0: [sdb] tag#4 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.587737] sd 1:0:0:0: [sdb] tag#4 CDB: opcode=0x2a 2a 00 84 66 7d 58 00 00 01 00 [ 2526.587739] print_req_error: I/O error, dev sdb, sector 2221309272 [ 2526.588320] sd 1:0:0:0: [sdb] tag#5 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.588323] sd 1:0:0:0: [sdb] tag#5 CDB: opcode=0x2a 2a 00 84 66 7d 59 00 00 01 00 [ 2526.588325] print_req_error: I/O error, dev sdb, sector 2221309273 Und, wieder eine Platte im Raid1 verloren rock64@rockpro64v_2_1:~$ cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid1 dm-1[2](F) dm-0[1] 1953379392 blocks super 1.2 [2/1] [_U] bitmap: 5/15 pages [20KB], 65536KB chunk unused devices: <none> Leider habe ich nicht die Kenntnisse um zu erkennen, woran das liegt.
F

ROCKPro64 - Armbian armbian-config
Beobachtet Ignoriert Geplant Angeheftet Gesperrt Verschoben Armbian armbian rockpro64
1

3

0 Stimmen

1 Beiträge

774 Aufrufe

Niemand hat geantwortet
F

ROCKPro64 - USB3 bootet von SSD!
Beobachtet Ignoriert Geplant Angeheftet Gesperrt Verschoben ROCKPro64 rockpro64
4

0 Stimmen

4 Beiträge

893 Aufrufe

F

Da oben steht viel Bullshit Ich habe mich mal mit dem mechanischen Aufbau einer USB3 Buchse beschäftigt, bzw. dazu recherchiert. Auf dieser Seite ist ein klasse Bild, was das sehr gut verdeutlicht. https://kompendium.infotip.de/usb-3-0.html Abbildung 28. Dort sieht man das die USB3 Kontakte RX/TX und GND ganz hinten sind. Wenn ich den Stecker jetzt komplett einstecke, wird wohl versucht eine USB3 Verbindung aufzubauen, die ja im Moment aus irgendeinem Grund scheitert. Wenn ich den Stecker nun ein Stück raus ziehe, trenne ich die USB3-Verbindung und es kommt eine USB2-Verbindung zustande. So mit ist mir jetzt einiges klarer, aber das Problem ist ungelöst
F

960 EVO M.2 vs. 970 PRO M.2
Beobachtet Ignoriert Geplant Angeheftet Gesperrt Verschoben ROCKPro64 rockpro64
2

0 Stimmen

2 Beiträge

2k Aufrufe

F

Die 970 steckt jetzt in meinem Haupt-PC. Dort werkelt ein aktuelles Linux Mint Cinnamon 19. Zum Vergleich. 100M frank@frank-MS-7A34:~$ sudo iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 [sudo] Passwort für frank: Iozone: Performance Test of File I/O Version $Revision: 3.429 $ Compiled for 64 bit mode. Build: linux-AMD64 Contributors:William Norcott, Don Capps, Isom Crawford, Kirby Collins Al Slater, Scott Rhine, Mike Wisner, Ken Goss Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR, Randy Dunlap, Mark Montague, Dan Million, Gavin Brebner, Jean-Marc Zucconi, Jeff Blomberg, Benny Halevy, Dave Boone, Erik Habbinga, Kris Strecker, Walter Wong, Joshua Root, Fabrice Bacchella, Zhenghua Xue, Qin Li, Darren Sawyer, Vangel Bojaxhi, Ben England, Vikentsi Lapa. Run began: Sun Aug 19 16:52:19 2018 Include fsync in write timing O_DIRECT feature enabled Auto Mode File size set to 102400 kB Record Size 4 kB Record Size 16 kB Record Size 512 kB Record Size 1024 kB Record Size 16384 kB Command line used: iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Output is in kBytes/sec Time Resolution = 0.000001 seconds. Processor cache size set to 1024 kBytes. Processor cache line size set to 32 bytes. File stride size set to 17 * record size. random random bkwd record stride kB reclen write rewrite read reread read write read rewrite read fwrite frewrite fread freread 102400 4 92640 121912 131074 139525 45719 116653 102400 16 254286 285267 285539 320370 108049 314486 102400 512 537947 581765 606103 598137 537701 588214 102400 1024 566892 547921 567369 597286 518014 558686 102400 16384 1407884 1642148 1941120 2115608 2006947 1668118 iozone test complete. 1000M frank@frank-MS-7A34:~$ sudo iozone -e -I -a -s 1000M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Iozone: Performance Test of File I/O Version $Revision: 3.429 $ Compiled for 64 bit mode. Build: linux-AMD64 Contributors:William Norcott, Don Capps, Isom Crawford, Kirby Collins Al Slater, Scott Rhine, Mike Wisner, Ken Goss Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR, Randy Dunlap, Mark Montague, Dan Million, Gavin Brebner, Jean-Marc Zucconi, Jeff Blomberg, Benny Halevy, Dave Boone, Erik Habbinga, Kris Strecker, Walter Wong, Joshua Root, Fabrice Bacchella, Zhenghua Xue, Qin Li, Darren Sawyer, Vangel Bojaxhi, Ben England, Vikentsi Lapa. Run began: Sun Aug 19 15:28:38 2018 Include fsync in write timing O_DIRECT feature enabled Auto Mode File size set to 1024000 kB Record Size 4 kB Record Size 16 kB Record Size 512 kB Record Size 1024 kB Record Size 16384 kB Command line used: iozone -e -I -a -s 1000M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Output is in kBytes/sec Time Resolution = 0.000001 seconds. Processor cache size set to 1024 kBytes. Processor cache line size set to 32 bytes. File stride size set to 17 * record size. random random bkwd record stride kB reclen write rewrite read reread read write read rewrite read fwrite frewrite fread freread 1024000 4 95635 121379 108328 108265 45369 123356 1024000 16 239238 314359 245937 241877 105865 297193 1024000 512 596812 620661 442100 382367 351948 613525 1024000 1024 608903 611898 434687 417192 412018 646465 1024000 16384 1898738 2004622 2143647 2188062 2099674 1983240 iozone test complete. Da scheint auf dem ROCKPro64 noch ein wenig Luft nach oben.
F

Infrarot Empfänger
Beobachtet Ignoriert Geplant Angeheftet Gesperrt Verschoben Hardware hardware rockpro64
1

0 Stimmen

1 Beiträge

809 Aufrufe

Niemand hat geantwortet
F

DTS DTB Files bearbeiten
Beobachtet Ignoriert Geplant Angeheftet Gesperrt Verschoben ROCKPro64 rockpro64
3

0 Stimmen

3 Beiträge

2k Aufrufe

F

Oder, ganz einfach sudo dtedit
F

Serielle Konsole UART2
Beobachtet Ignoriert Geplant Angeheftet Gesperrt Verschoben Hardware hardware rockpro64
8

2

0 Stimmen

8 Beiträge

3k Aufrufe

F

Ich verweise mal auf einen Artikel auf einer Webseite von mir, der Einsteiger Niveau hat. https://frank-mankel.de/wichtig/serielle-konsole Wenn es dann noch Probleme gibt, einfach fragen. Und beachte bitte, das wir hier nicht über PIs schreiben, sondern über ROCKPros. Da könnte es kleine Unterschiede geben. https://www.raspberrypi.org/documentation/configuration/uart.md