| Type | Item | Description |
|---|---|---|
| Processor: | StarFive JH7110 | StarFive JH7110 with RISC-V quad-core CPU with 2 MB L2 cache and a monitor core, supporting RV64GC ISA, working up to 1.5 GHz |
| Imagination GPU | IMG BXE-4-32 MC1 with work frequency up to 600 MHz | |
| Memory: | 2 GB/4 GB/8 GB | LPDDR4 SDRAM, up to 2,800 Mbps |
| Storage: | Onboard TF card slot | The VisionFive 2 can boot from a TF card. |
| Flash | The firmware to store U-Boot and bootloader. | |
| Multimedia: | Video Output | 1 × 2-lane MIPI DSI display port, supporting up to 1080p@30fps |
| 1 × 4-lane MIPI DSI display port, supporting up to 2K@30fps in both single display and dual display modes. | ||
| 1 × HDMI 2.0, supporting up to 4K@30fps or 2K@60fps | ||
| Note: Only one MIPI DSI port can be used for display at a time. | ||
| Camera | 1 × 2-lane MIPI CSI camera port, supporting up to 1080p@30fps | |
| Encoder/Decoder | Video decoder supports up to 4K@60fps and multi-stream for H264/H265; | |
| Video encoder supports up to 1080p@30fps and multi-stream for H265; | ||
| JPEG encoder/decoder | ||
| Audio | 4-pole stereo audio jack | |
| Connectivity: | Ethernet | 2 × RJ45 Gigabit Ethernet ports |
| USB Host | 4 × USB 3.0 ports (multiplexed with a PCIe 2.0 1x lane). | |
| USB Device | 1 × USB device port (by reusing the USB-C port) | |
| M.2 Connector | M.2 M-Key | |
| eMMC Socket | For eMMC modules as OS and data storage | |
| 2-Pin Fan Header | - | |
| Power: | USB-C port | 5 V DC via USB-C with PD, up to 30 W (minimum 3 A) |
| GPIO Power In | 5 V DC via GPIO header (minimum 3 A) | |
| PoE (Power over Ethernet) | PoE function is enabled and requires separate PoE HAT | |
| GPIO: | 40-Pin GPIO Header | 1 × 40-pin GPIO header, supporting various interface options: |
| 3.3 V (on 2 pins) | ||
| 5 V (on 2 pins) | ||
| Ground (on 8 pins) | ||
| GPIO | ||
| CAN bus | ||
| DMIC | ||
| I2C | ||
| I2S | ||
| PWM | ||
| SPI | ||
| UART | ||
| and so on | ||
| Boot Mode: | Boot mode setting pins | You can choose one of the following boot modes: |
| 1-bit QSPI Nor Flash | ||
| SDIO3.0 | ||
| eMMC | ||
| UART | ||
| Button: | Reset button | To reset VisionFive 2, press and hold the Reset button for more than 3 seconds to ensure the reset is successful. |
| Dimensions: | 100 × 74 mm | - |
| Compliance: | RoHS, FCC, CE | - |
| Environment: | Recommended operating temperature | 0-50 ℃ |
| Other: | Debug function | UART TX and UART RX are available through the 40-pin GPIO header. |
Quelle: https://doc-en.rvspace.org/VisionFive2/Quick_Start_Guide/VisionFive_2/specification_pb.html
Schaltdiagramm -> https://doc-en.rvspace.org/VisionFive2/PDF/SCH_RV002_V1.2A_20221216.pdf
