Skip to content

FAN control OMV Auyfan 0.10.12: gitlab-ci-linux-build-184, Kernel 5.6

Linux
  • Hey,

    I will do it in english, hope it is okay. Thanks, for very informative forum.

    My question is, is it possible to control the FAN in the newest OMV Auyfan 0.10.12: gitlab-ci-linux-build-184, Kernel 5.6?
    The install was very easy no problems at all, the only problem is i did try some different commands to reach the fan, but was not able to get it going. Do somebody know how? Thanks.

    Best Regards.
    Soeren

  • Hi Soeren,

    I have this succesfully running.

    Kind Regards
    Martin

  • @mabs sagte in FAN control OMV Auyfan 0.10.12: gitlab-ci-linux-build-184, Kernel 5.6:

    Hi Soeren,

    I have this succesfully running.

    Kind Regards
    Martin

    Thanks, i will try the fan tool again. I'm almost sure i did try without luck, have you edited something in the fan tool conf..?

  • Hi,

    I only played with two parameters.

    I have two rockpro64 boards, currently one has a small fan and the other one has a large fan.

    Therefore I changed PROFILE_NR accordingly.

    Also I have ALWAYS_ON on true on the one with the large fan, but don't see a difference. The fan goes on and off still, maybe I misinterpreted the parameter.

    Also I just noticed now that the CTL settings of the version on github changed slightly, but I think this only improved the detection depending of the kernel settings.

    M

  • @mabs

    With the new OMV kernel 5.6 image from Auyfan, i can't get the FAN to spin - If the fan spins it runs really slow, no sound from the fan.

    With the FAN tool the master installation "failed" and with the release installation it did report "active"..
    I have installed a 92mm FAN inside the NAS case, it runs on Armbian with kernel 5.4.32

    I will open op the case later today to be sure. Thanks.

  • Hi,

    Now i did find the fan, here it goes "nano /sys/devices/platform/pwm-fan/hwmon/hwmon3/pwm1" it is at "0" can be controlled to "255"

    Best Regards.

  • Yes that is basically the way ATS is doing the changing as well I think, as those /sys entries are in the _CTL variables.

    good that you got it working, or are you only half way?

    M

  • @mabs

    The tool works on all image under 5.4 or so for me. But yes i am at the finish line, just wanted the fan to be always on. Just wanted to share, if someone will run in the same problems. Thanks.

  • Helpful Thread!

    But, ATS don't work for me on kernel 5.6 with ayufan release. Only this command works.

    nano /sys/devices/platform/pwm-fan/hwmon/hwmon3/pwm1
    

    Thanks @soerenderfor for the hint.

  • Ok, problem in ATS is this?

    -- FAN Control[ String ]
    	PWM_CTL		= {
    			"/sys/class/hwmon/hwmon0/pwm1",
    			"/sys/devices/platform/pwm-fan/hwmon/hwmon0/pwm1",
    			"/sys/devices/platform/pwm-fan/hwmon/hwmon1/pwm1"
    	},
    
  • @FrankM - did you try fix the ATS tool, if yes. Will it Work?

    Best Regards.

  • Hi,

    since I'm currently change my rockpro64 setup I came across this.

    With the kernel from ayufan you need to set PWM_CTL to

    /sys/devices/platform/pwm-fan/hwmon/hwmon3/pwm1
    

    for my self compiled one I need

    /sys/devices/platform/pwm-fan/hwmon/hwmon0/pwm1
    

    But I got it only working with one entry for PWM_CTL e.g.

    PWM_CTL		= "/sys/devices/platform/pwm-fan/hwmon/hwmon0/pwm1",
    

    after that you need to start ats again

    sudo systemctl stop ats
    sudo systemctl start ats
    

    initially the fan should start immediately for a short period of time.

    In case it is even a different one on your kernel you can find the right one using this command.

    sudo find /sys -name pwm1 | grep hwmon
    

    So far I'm not sure which kernel parameter or modul changes this.

    Martin

  • RISC-V

    VisionFive 2
    1
    0 Stimmen
    1 Beiträge
    63 Aufrufe
    Niemand hat geantwortet
  • Hetzner Cloud - Volumes

    Allgemeine Diskussionen
    1
    0 Stimmen
    1 Beiträge
    893 Aufrufe
    Niemand hat geantwortet
  • NanoPi R2S - OpenWRT

    Verschoben NanoPi R2S
    6
    0 Stimmen
    6 Beiträge
    517 Aufrufe
    FrankMF

    @thrakath1980 Ich wollte noch auf ein Thema zurück kommen. Das Original OpenWRT auf dem R2S ist ja ein Snapshot. Den kann man ohne Probleme aktualisieren. Unten ist dann ein Haken mit "Keep settings...."

    Gerade probiert, ging einwandfrei. Netzwerkeinstellungen und Firewall Settings blieben erhalten.

  • 0 Stimmen
    3 Beiträge
    388 Aufrufe
    FrankMF

    Gestern mal das Ganze mit einem Cinnamon Desktop ausprobiert. Eine verschlüsselte Installation auf eine PCIe NVMe SSD. So weit lief das alles reibungslos. Der Cinnamon Desktop hat dann leider keine 3D Unterstützung. Sieht so aus, als wenn keine vernünftigen Grafiktreiber genutzt würden. Da ich auf diesem Gebiet aber eine Null bin, lassen wir das mal so. Außerdem mag ich sowieso keine Desktops auf diesen kleinen SBC. Da fehlt mir einfach der Dampf 😉

    Gut, was ist mir so aufgefallen?

    Unbedingt die Daten des Daily Images erneuern, keine alten Images nutzen. Ich hatte da jetzt ein paar Mal Schwierigkeiten mit. Da das ja nun keine Arbeit ist, vorher einfach neu runterladen und Image bauen.

    Warum zum Henker bootet eigentlich. außer meiner Samsung T5, nichts vom USB3 oder USB-C Port?? 👿

  • Debian Minimal von Mr.Fixit2001

    Linux
    4
    0 Stimmen
    4 Beiträge
    429 Aufrufe
    FrankMF

    Release 190531 - Updated Debian Minimal Release

    Kernel Updated to 4.4.180 Additional Kernel Fixes U-Boot patched to fix weird issue where only some EMMC modules will not boot
  • Mainline Kernel 4.18.0-rc3

    Linux
    1
    0 Stimmen
    1 Beiträge
    945 Aufrufe
    Niemand hat geantwortet
  • Mainline Kernel 4.20.x

    Verschoben Images
    26
    0 Stimmen
    26 Beiträge
    4k Aufrufe
    FrankMF

    4.20.0-1090-ayufan released

    Änderungen -> https://gitlab.com/ayufan-repos/rock64/linux-mainline-kernel/commits/master

  • Mainline Kernel 4.17-rc7

    Verschoben Archiv
    8
    0 Stimmen
    8 Beiträge
    2k Aufrufe
    FrankMF

    4.17.0-rc6-1029-ayufan released

    Link Preview Image Releases · ayufan-rock64/linux-mainline-kernel

    Linux kernel source tree. Contribute to ayufan-rock64/linux-mainline-kernel development by creating an account on GitHub.

    favicon

    GitHub (github.com)

    Seit 1021 funktioniert USB3.