@frankm Alles Klar!
Wie schon erwähnt, für meine Zwecke rechts! Die Jahre über hat gute Dienste geleistet (PCI-e und HDD) und wird hoffentlich auch noch ein paar Jahre bis zum nächsten Umbau tun!
Vielen Dank!
SATA - Booten jetzt möglich
-
Wie ich gestern schon schrieb, hat Sigmaris seinen u-boot aktualisiert.
https://forum.frank-mankel.org/topic/746/u-bootDas möchte ich dann heute Morgen beim Kaffee mal testen
Auf geht's. Das Image auf die SD-Karte und ab in den ROCKPro64 damit.Bitte beachtet die Anleitung!
Die Ausgabe
U-Boot 2020.01-rc5-01969-g0bfd4738c6 (Jan 03 2020 - 15:46:36 +0000) Model: Pine64 RockPro64 DRAM: 2 GiB PMIC: RK808 MMC: dwmmc@fe320000: 1, sdhci@fe330000: 0 Loading Environment from SPI Flash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment In: serial@ff1a0000 Out: serial@ff1a0000 Err: serial@ff1a0000 Model: Pine64 RockPro64 rockchip_dnl_key_pressed: adc_channel_single_shot fail! Net: eth0: ethernet@fe300000 Hit any key to stop autoboot: 0 Card did not respond to voltage select! switch to partitions #0, OK mmc1 is current device Scanning mmc 1:3... Found U-Boot script /boot.scr 967 bytes read in 5 ms (188.5 KiB/s) ## Executing script at 00500000 SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB 1363484 bytes read in 63 ms (20.6 MiB/s) device 0 offset 0x0, size 0x14ce1c 1220124 bytes written, 143360 bytes skipped in 14.674s, speed 95148 B/s Wrote U-Boot to SPI Flash successfully. U-Boot TPL 2020.01-01987-g335875f1f5 (Feb 01 2020 - 15:02:32) Channel 0: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS=1 Die BW=16 Size=1024MB Channel 1: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS=1 Die BW=16 Size=1024MB 256B stride 256B stride lpddr4_set_rate: change freq to 400000000 mhz 0, 1 lpddr4_set_rate: change freq to 800000000 mhz 1, 0 Trying to boot from BOOTROM Returning to boot ROM... U-Boot SPL 2020.01-01987-g335875f1f5 (Feb 01 2020 - 15:02:32 +0000) Trying to boot from SPI NOTICE: BL31: v2.2(release):v2.2-271-g9a943ba43 NOTICE: BL31: Built : 15:00:49, Feb 1 2020 U-Boot 2020.01-01987-g335875f1f5 (Feb 01 2020 - 15:02:32 +0000) Model: Pine64 RockPro64 DRAM: 2 GiB PMIC: RK808 MMC: dwmmc@fe320000: 1, sdhci@fe330000: 0 Loading Environment from SPI Flash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment In: serial@ff1a0000 Out: serial@ff1a0000 Err: serial@ff1a0000 Model: Pine64 RockPro64 Net: eth0: ethernet@fe300000 Hit any key to stop autoboot: 0 Card did not respond to voltage select! Card did not respond to voltage select! PCIE-0: Link downHier der Schreibvorgang
Found U-Boot script /boot.scr 967 bytes read in 5 ms (188.5 KiB/s) ## Executing script at 00500000 SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB 1363484 bytes read in 63 ms (20.6 MiB/s) device 0 offset 0x0, size 0x14ce1c 1220124 bytes written, 143360 bytes skipped in 14.674s, speed 95148 B/s Wrote U-Boot to SPI Flash successfully.Gut, dann jetzt zum SATA-Test.
SATA-Test
Hardware
- Pine64 Adapter
- SanDisk Ultra SSD 3D 1TB
Stromversorgung erfolgt über ein PC-Netzteil.
Software
Ein jungfräuliches Armbian. Dann starten wir mal, hier die Ausgabe.
Willkommen zu minicom 2.7.1 Optionen: I18n Übersetzt am May 6 2018, 08:02:47. Port /dev/ttyUSB0 Drücken Sie CTRL-A Z für Hilfe zu speziellen Tasten U-Boot TPL 2020.01-01987-g335875f1f5 (Feb 01 2020 - 15:02:32) Channel 0: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS=1 Die BW=16 Size=1024MB Channel 1: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS=1 Die BW=16 Size=1024MB 256B stride 256B stride lpddr4_set_rate: change freq to 400000000 mhz 0, 1 lpddr4_set_rate: change freq to 800000000 mhz 1, 0 Trying to boot from BOOTROM Returning to boot ROM... U-Boot SPL 2020.01-01987-g335875f1f5 (Feb 01 2020 - 15:02:32 +0000) Trying to boot from SPI NOTICE: BL31: v2.2(release):v2.2-271-g9a943ba43 NOTICE: BL31: Built : 15:00:49, Feb 1 2020 U-Boot 2020.01-01987-g335875f1f5 (Feb 01 2020 - 15:02:32 +0000) Model: Pine64 RockPro64 DRAM: 2 GiB PMIC: RK808 MMC: dwmmc@fe320000: 1, sdhci@fe330000: 0 Loading Environment from SPI Flash... SF: Detected gd25q128 with page size 256 B *** Warning - bad CRC, using default environment In: serial@ff1a0000 Out: serial@ff1a0000 Err: serial@ff1a0000 Model: Pine64 RockPro64 Net: eth0: ethernet@fe300000 Hit any key to stop autoboot: 0 Card did not respond to voltage select! Card did not respond to voltage select! PCIE-0: Link up (Bus0) Device 0: unknown device scanning bus for devices... SATA link 0 timeout. Target spinup took 0 ms. AHCI 0001.0200 32 slots 2 ports 6 Gbps 0x3 impl SATA mode flags: 64bit ncq stag led clo pmp pio slum part ccc sxs Device 0: (1:0) Vendor: ATA Prod.: SanDisk SDSSDH3 Rev: 4011 Type: Hard Disk Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) Device 0: (1:0) Vendor: ATA Prod.: SanDisk SDSSDH3 Rev: 4011 Type: Hard Disk Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) ... is now current device Scanning scsi 0:1... Found U-Boot script /boot/boot.scr 2940 bytes read in 10 ms (287.1 KiB/s) ## Executing script at 00500000 Boot script loaded from scsi 0 151 bytes read in 9 ms (15.6 KiB/s) 6928122 bytes read in 120 ms (55.1 MiB/s) 20987912 bytes read in 345 ms (58 MiB/s) 96273 bytes read in 19 ms (4.8 MiB/s) ## Loading init Ramdisk from Legacy Image at 06000000 ... Image Name: uInitrd Image Type: AArch64 Linux RAMDisk Image (gzip compressed) Data Size: 6928058 Bytes = 6.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01f00000 Booting using the fdt blob at 0x1f00000 Loading Ramdisk to 7d861000, end 7defc6ba ... OK ERROR: reserving fdt memory region failed (addr=0 size=0) Loading Device Tree to 000000007d7e1000, end 000000007d860fff ... OK Starting kernel ... Armbian 19.11.7 Buster ttyS2 rockpro64 login:Der interessante Teil
SATA link 0 timeout. Target spinup took 0 ms. AHCI 0001.0200 32 slots 2 ports 6 Gbps 0x3 impl SATA mode flags: 64bit ncq stag led clo pmp pio slum part ccc sxs Device 0: (1:0) Vendor: ATA Prod.: SanDisk SDSSDH3 Rev: 4011 Type: Hard Disk Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) Device 0: (1:0) Vendor: ATA Prod.: SanDisk SDSSDH3 Rev: 4011 Type: Hard Disk Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) ... is now current deviceDie SSD wird am SATA-Adapter erkannt und von dort gebootet. Yeah!
root@rockpro64:~# df -h Filesystem Size Used Avail Use% Mounted on udev 960M 0 960M 0% /dev tmpfs 193M 7.8M 185M 5% /run /dev/sda1 909G 5.2G 894G 1% / tmpfs 963M 0 963M 0% /dev/shm tmpfs 5.0M 4.0K 5.0M 1% /run/lock tmpfs 963M 0 963M 0% /sys/fs/cgroup tmpfs 963M 4.0K 963M 1% /tmp /dev/zram0 49M 1.3M 44M 3% /var/log tmpfs 193M 0 193M 0% /run/user/0Das Armbian dauert beim ersten Start etwas, das Filesystem wird expandiert. Danach kommt das hier
____ _ ____ __ _ _ | _ \ ___ ___| | _| _ \ _ __ ___ / /_ | || | | |_) / _ \ / __| |/ / |_) | '__/ _ \ | '_ \| || |_ | _ < (_) | (__| <| __/| | | (_) | | (_) |__ _| |_| \_\___/ \___|_|\_\_| |_| \___/ \___/ |_| Welcome to Armbian buster with Linux 4.4.208-rockchip64 System load: 0.06 0.34 0.19 Up time: 5 min Memory usage: 5 % of 1925MB IP: 192.168.3.14 CPU temp: 41°C Usage of /: 1% of 909G Last login: Sun Feb 2 07:37:05 2020 from 192.168.3.213Funktioniert
Schnell noch ein Speedtest
root@rockpro64:~# iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Iozone: Performance Test of File I/O Version $Revision: 3.429 $ Compiled for 64 bit mode. Build: linux Contributors:William Norcott, Don Capps, Isom Crawford, Kirby Collins Al Slater, Scott Rhine, Mike Wisner, Ken Goss Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR, Randy Dunlap, Mark Montague, Dan Million, Gavin Brebner, Jean-Marc Zucconi, Jeff Blomberg, Benny Halevy, Dave Boone, Erik Habbinga, Kris Strecker, Walter Wong, Joshua Root, Fabrice Bacchella, Zhenghua Xue, Qin Li, Darren Sawyer, Vangel Bojaxhi, Ben England, Vikentsi Lapa. Run began: Sun Feb 2 07:38:17 2020 Include fsync in write timing O_DIRECT feature enabled Auto Mode File size set to 102400 kB Record Size 4 kB Record Size 16 kB Record Size 512 kB Record Size 1024 kB Record Size 16384 kB Command line used: iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Output is in kBytes/sec Time Resolution = 0.000001 seconds. Processor cache size set to 1024 kBytes. Processor cache line size set to 32 bytes. File stride size set to 17 * record size. random random bkwd record stride kB reclen write rewrite read reread read write read rewrite read fwrite frewrite fread freread 102400 4 37751 45682 53103 54242 29458 45794 102400 16 91193 101342 110226 113039 65179 100783 102400 512 160846 172882 174878 173878 156964 173685 102400 1024 173077 174518 169235 175272 167570 175185 102400 16384 185940 187884 196006 195967 195369 188492 iozone test complete. root@rockpro64:~# dd if=/dev/zero of=sd.img bs=1M count=4096 conv=fdatasync 4096+0 records in 4096+0 records out 4294967296 bytes (4.3 GB, 4.0 GiB) copied, 23.2034 s, 185 MB/sNicht optimal mit dieser SSD, aber das dürfte so in etwa das Maximum sein, was man mit dem Adapter erreichen kann.
Noch schnell getestet, was geht.
- SATA - Ja
- PCIe NVMe - Ja
- USB3 - Nein
- USB2 - Ja
- SD - Ja
- eMMC - ???
eMMC zwar getestet, aber ich bin mir nicht sicher ob meine Karte noch lebt.
Fazit
Schöner u-boot wenn man von PCIe NVMe oder SATA booten möchte. Jetzt noch funktionierendes USB3 und der u-boot ist fertug
Danke @ sigmaris!!
-
-
-
NVMe SSD Speed auf Kernel 5.0 von Kamil
Verschoben ROCKPro64 -
Booten von USB3
Verschoben ROCKPro64 -
-
-
-
[HOWTO] ROCKPro64 - Boot
Verschoben Hardware